Search Documents

By L. A. Haas

In this Bureau of Mines investigation, conditions were determined to form an iron sulfide adherent coating with a metallic golden luster on steel upon anaerobic heat treatment with sulfur. The sulfide formation rate was determined in the temperature range of 105° to 500° C with reaction times up to 68 hours. The optimum temperature and time to form an adhering decorative coating on mild steel was in the range of 105° C for about 70 hours to 285° C for 1 hour. The golden coating consisted of an inner layer of pyrrhotite and an outer layer of pyrite. At temperatures higher than about 300° C, the outer layer thickness decreased owing to the decomposition of pyrite to pyrrhotite.. Small quantities (<0.5 wt-pct) of petroleum oil accelerated the sulfide growth rate. The sulfide coating decreased the corrosion rate of steel in a neutral aqueous medium by a factor of two. The dissolution of pyrite in water was dependent on particle size and surface area with the flat pyrite coatings exhibiting the lowest dissolution rate.

Jan 1, 1974

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result- ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coalbed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beck- ley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation&apos;s mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By R. V. Ramani, C. B. Manula, A. Owili-Eger

The mine ventilation system consists of the fan, the roadways, and the regulatory devices. Sufficient fresh air must reach each working face in the mines to render harmless noxious, toxic, and respirable pollutants and to provide for the breathing of men. This is achieved by the proper selection of fan and regulatory devices. Because a mining system is dynamic, the mine ventilation system must also be dynamic. In short, mine ventilation engineers are frequently called upon to provide answers to the following questions: 1. Given a mine or the projected plan of a mine, what fan must be selected for the quantities specified in the section? At what point in its characteristic must it be operated? Are any speed changes or changes in blade settings warranted? 2. What should be the regulation in a section to insure cer¬tain desired quantity in that section? How does it affect the overall ventilation system? 3. What are the effects of driving a new shaft? Where should it be located? What size fan should be installed in the shaft? How does this affect the overall ventilation sys¬tem? 4. How much quantity increases can be obtained by cleaning up falls and streamlining roadways and by driving addi¬tional parallel airways? These questions are in no way exhaustive, nor are answers easy. Most of the operational and planning problems discussed above are to a cer¬tain extent solved by ventilation engineers using rules of thumb from experience. Both natural conditions and regulatory requirements have changed so drastically recently that use of scientific methods in ventilation planning and of faster methods in evaluating the plans is a must. Fortunately, computers offer the greatest hope for good

Jan 1, 1975

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1956 and 1956 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding table., for 1955 and 1956 follow in consecutive order under the following general sections: (A) General injury experience: Tables I to II: contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury data: Tables 12 to 77: Contain current data on causes of injuries, distribution of injuries by part of body injured, clays of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation&apos;s coal mines. (C) Injury experience, by States: Tables 78 to 87: Contain data on injuries, injury rates, employment, cause of injuries, aid severity rates by States. (D) Major disasters: Table 88: Contains data on major disasters, 1947 -56. A major disaster is defined as a single accident in which, or as the result of which, five or more persons are killed instantly or died at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 89 to 93: Contain data on fatalities and their causes at bituminous-coal and anthracite mines from the earliest records through 1956.

Jan 1, 1960

Remotely monitor overburden response to longwall mining using time domain reflectometry (TDR) and a combination of hardware and software, as part of the U.S. Bureau of Mines (USBM) program to characterize subsidence. Background TDR was developed in the 1960&apos;s as a method to locate, discontinuities in coaxial transmission cables. In this method, voltage pulses sent along a cable are reflected by cable defects. The pulse reflections are used to determine the type and magnitude of the defects. The TDR concept was extended to material property measurement by embedding cables into particular materials and evaluating the cable&apos;s dielectric behavior as material properties were modified. This technique was adapted by the USBM in 1978 for use in monitoring rock movement during underground mining. The same concept is utilized today. A coaxial cable is grouted into a rock mass that is expected to deform. Progressive rock movement causes the cable to deform, as shown in figure 1, and changes to occur in the cable&apos;s electrical properties, which then produce changes in TDR reflection signatures. The technology has advanced to the point where it is now possible to distinguish shear deformation from tensile deformation and to quantify rock mass displacements by analyzing the TDR signatures.

Jan 1, 1995

By Ferron A. Olson

Natural bornite (Cu5FeS4) leached in ferric chloride or in sulfuric or hydrochloric acid solutions with oxygen showed several differences. In ferric chloride 80 of the copper was leached in two stages. The first (30 copper removal) requiring one minute was controlled by mixed kinetics (liquid ferric ion diffusion and chemical surface reaction). The second was controlled by formation of a surface sulfur layer and then diffusion through the sulfur. With oxygen in sulfuric acid reaction was slow and only the first stage was studied. Copper removal had an induction period. The bornite structure disappeared at 12% copper removal (also found with ferric chloride) and covellite formed on the surface with a species inside the particles having an x-ray structure similar to CuFeS2 but with composition Cu3FeS4 (also with ferric chloride). Copper removal was controlled by iron dissolution. Surface iron vacancies filled with Cu+ to give CuS while interior copper dissolution produced Cu3FeS4. Preliminary results with oxygen and hydrochloric acid showed 80% copper removal and sulfur as end products (similar to ferric chloride).

Jan 1, 1982

By Paul W. Jeran

Subsidence over a series of longwall panels undermining sloping terrain in southwestern Pennsylvania was monitored to verify the Bureau of Mines subsidence prediction model for the northern Appalachian coal region. Comparison of the field data to model output shows close agreement. Vertical movements over each panel ceased with the mining of the adjacent panel. Horizontal movements were significantly affected by topographic slope. The distribution of horizontal strains over each panel were similar, with a zone of compression occurring over the center of each panel. The zones of compression were flanked by zones of tension toward the rib. The magnitude of the tensions were affected by the slope. The strains developed at the completion of each panel were not significantly altered by the mining of subsequent panels.

Jan 1, 1988

By Virgil A. Marple

The objective of this contract was to conduct characterization, evaluation and/or calibration studies of instrumentation used for measuring the quantity of respirable dust in mining atmospheres. Initially, this work involved the upgrading and detailed evaluation of the aerosol test chamber and the development of impactors with respirable classification characteristics. These were used as standards in the chamber for measuring the quantity of respirable dust based on either the ACGIH or BMRC respirable dust criteria. A program was then conducted to calibrate several photometers. In addition, the mass sensitivity of the GCA RAM-1 photometer to water droplets in the respirable size range was determined. Three additional studies were also made in this program. First, an experimental study was performed to ascertain the effect of crosswind, cyclone orientation and particle size on particle sampling and penetration through the 10 mm Dorr-Oliver cyclone. Second, a theoretical study was conducted to refine the theory used to predict the particle collection characteristics of impactors. Third, filter samples with known quantities of diesel and coal particles were produced and delivered to the B. of Mines for testing a Raman scattering analysis technique to discriminate diesel particles in the presence of coal dust.

Jan 1, 1984

By Daryl R. Tweeton

This Bureau of Mines publication ill scribes present practices of making injection wells for in situ uranium leaching. Casings, screens, drilling fluids, coring, logging, cementing, and developing are discussed with the objective of aiding those who are starting an in situ leaching operation. Improper choices of materials or techniques can result in wells that are either useless or wells that have an undesirably high resistance to injection. Important factors include careful selection of screen slot size, use of logs for choosing the cementing basket depth, proper cementing techniques, and careful choice, use, and flushing of drilling fluids. The information was obtained through observation of well construction and through discussion with in situ leaching companies, drillers, and suppliers.

Jan 1, 1978

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By Alexander L. Peyton

The Magruder and Chambers copper deposits in the Little River gold district, on the border line of Lincoln and Wilkes Counties, Georgia, have been known for a number of years (fig. 1). The Magruder deposit was first opened as a gold mine but has produced mostly copper and load. Records show that about 50 cars of concentrates were shipped from this property. No record of any production at the Chambers deposit is available. The Bureau of Mines, in its program of investigation of strategic minerals deposits, diamond drilled 10 holes, totaling 3,784 feet, on the two properties between December 3, 1948, and June 23, 1949. Eighty-eight core samples were analyzed, and the analyses and drill-hole data are presented in this report.

Jan 1, 1950

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso-and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, O2, N2, H2, and He; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By Charles D. Wood

"Selected Topics,? in reviewing the control of emissions from diesel engine powered equipment used in underground mining, explores these fields of interest: hydrogen as fuel; lubricating oil as a source of particulates; applicability of stationary source scrubbers; worldwide diesel exhaust scrubbers; instrumentation technology for measurement of N02; control of emissions through application of sensors and microprocessors; use of fuel additives; technology transfer of marine diesel practice; technology required to use 4-stroke, aftercooled, turbocharged, direct injection engines; oxidation and reduction catalysts for diesel engine exhausts. "Selected Topics? makes recommendations for research and provides a bibliography and lists of references.

Jan 1, 1979

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982