Search Documents

By Virginia E. Gleason

In this report, recommendations are made for programs to develop workable techniques to stop or prevent acid mine drainage formation in those underground coal mines where acid production could take place. These recommendations include development of mine closure technology, development of surface water infiltration control procedures, study of the effect of roof collapse on mine water characteristics, evaluation of the long-term effects of flooding underground mines above drainage, investigation of the effectiveness of section sealing in active mines, development of a simple model for predicting mine water quality and quantity, preparation of a manual on mine drainage abatement procedures, and development of a program to disseminate information on mine drainage abatement to the coal industry. These recommendations are based on an in-depth evaluation of information acquired over years of research on acid mine drainage formation, on numerous laboratory and field studies of methods of preventing or minimizing acid mine drainage formation, and on review of the geological, hydrological, and mineralogical factors involved. There are 772 references.

Jan 1, 1978

By Terry R. Neumann

In 1989, the Bureau of Mines conducted a mineral resource investigation of the 52,350-acre Jersey Jack study area, located in the Clearwater Mountains of north-central Idaho. Twenty-eight mines and prospects were examined, and 483 rock, placer, and petrographic samples were collected during the field study. Two properties contain gold resources; mining company data show the Robinson Dike mine contains an estimated 940,000 tons of "drill proven and probable reserves" averaging 0.041 oz/ton gold, and the Bureau of Mines investigation showed the Blacksand placer mine contains an estimated 64,000 cubic yards of identified placer resources averaging $8.13 in gold per cubic yard. Sample analyses from other properties indicate that gold resources are likely to exist; however the low tonnage, narrow, fissure-vein type deposits would require mining by relatively high-cost underground methods and would be subeconomic at a gold price of $400/oz.

Jan 1, 1991

As a result of early experiments in underground mine illumination, the Bureau of Hines recognized the need for additional experience with the underground lighting of coal mines having low seam thicknesses. There was already experience with tile illumination of coal mines having higher coal seams, and this contract with Ocean Energy Inc. (OEI) was undertaken to contribute to the "low coal" experience. For the purpose of this contract, a "low coal? mine is defined as one having less than 45 inches of overall headroom in the working places. As a practical limit, 26 inches was the minimum coal seam thickness to be encountered in this program. In one instance, the maximum coal seam thickness was eight to ten feet, however, this particular work was at the direction of the Technical Project Officer (TPO) by virtue of the unique type of lighting arrangement that was to be evaluated which would be useful for low coal. At the outset of the contract, three major tasks were established. The first two tasks involved the installation of permissible fluorescent lighting equipment at two low coal mines. The intention was to illuminate mining sections in each case consisting of one or more machines. The third task was to illuminate a variety or mining equipment including a longwall. For the purpose of this report, the fol-owing identifies the particular installations associated with each task.

Jan 1, 1976

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I describes an underground bituminous coal mine operation in a 48 inch seam, with an estimated production rate of 1,056,000 tons per year. The system includes four continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. This section illustrates the input data sequence and the various report formats which may be selected for the printing of results. As explained earlier, at the present time, the elements of the Cost Data Library must be read in with the regular data input. Thus, in the input data listing, immediately following the required user input, are cards which contain the inputs of the cost library. Examination of the cost reports indicate the absence of cost values for some categories for which the system would normally be expected to incur costs. This situation has arisen due to the format of the cost data provided in the U. S. Bureau of Mines reports. An example of this is the charge of $20/ton for brattice cloth while no charge is indicated for stoppings. The test report data provided a single figure for ventilation cost without a supplemental breakdown. Thus the cost indicated for brattice cloth is actually the total ventilation cost. These explanations hold true for the data input and output for Test II, Appendix III.

Jan 1, 1975

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By Lloyd A. Morley

The problems associated with the presence of organic materials and of water in explosion-proof enclosures used in high voltage, high capacity applications were examined through a literature search and theoretical reasoning. Information on volatilities is presented. The conclusion is reached that explosive pressures are significantly enhanced by inclusion of these materials.

Jan 1, 1976

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

Severe whipping of shuttle car trailing cables occurs when the car stops suddenly or reverses direction. This causes cable damage, and can seriously injure personnel near the cable. FMC has contracted with the U.S. Bureau of Mines to design, build and demonstrate a reel control system that will significantly reduce or eliminate whipping. II. CONCLUSIONS Results of engineering effort show that the following conditions are primarily responsible for the whipping problem. Causes may exist individually, or in combination.

Jan 1, 1972

By N. Kyriazi, W. Duerr, J. Shubilla, J. G. Kovac, J. Kravitz

A joint effort by the Bureau of Mines and the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, was undertaken to determine how well self-contained self-rescuers, deployed in accordance with Federal Regulations (30 CFK 75.1714), held up in the underground environment. This report presents findings regarding laboratory-tested breathing apparatus from the first year of a 5-yr program as well as other related findings. The SCSR's were tested on human subjects and on a breathing and metabolic simulator. These results indicate that the apparatus, if well-treated, perform as expected except for manufacturing defects or quality control problems, which are identified. However, when the apparatus are carried in and out of the mine every day and stored at the working section, they may suffer abuse that can be extreme. Physical signs of abuse, unless extremely obvious, frequently are not detected by the miners or the mine operators; this poses a danger to a potential user in case of emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1986

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By M. P. Hardy

Copper-Nickel ores in northeastern Minnesota could establish a new industry in a region where underground mining has not been active. This study reviews geotechnical data relevant to the selection and design of underground mines in this region and by numerical structural analysis evaluates the importance of some geotechnical parameters to mine method selection. Because of the rapid development of computer modeling many new techniques have become available for modeling rock mass behavior in recent years. An overview of these methods is presented and their applicability to mine design reviewed. Methods included in this summary were the differential continuum models, such as finite Pint and finite difference, integral continuum models, such as boundary element, displacement discontinuity and boundary integral equation methods, and discontinuum methods such as the distinct block model. The displacement discontinuity method was used to evaluate the influence of geotechnical parameters on some aspects of mine design. Three problems; room stability, pillar stability on a weak inclined contact and sill pillar thickness influence on sill pillar stability, were analyzed to evaluate the relative importance of insitu stress field and joint properties on design. It was concluded that for stability analysis the initial horizontal stress is of most importance in all aspects of design. The position, orientation, persistence and strength of joints is also of primary concern. In a more general sense, however, it was concluded that detailed geotechnical parameters have much less influence on mine method selection than more general factors such as rock quality, initial stress state, orebody shape and economics.

Jan 1, 1978

By Steven J. Page, John A. Organiscak, Thomas Mal

Monitoring the miner respirable quartz dust exposure for compliance with U.S. federal regulations is mandatory to protect the health of coal miners. However, there is no technique available for the direct measurement of the respirable quartz dust concentration in the mining environment. The only means to estimate the respirable quartz dust concentration is to perform an analysis of the respirable dust sample collected, which contains both coal and quartz dust as well as other mineral constituents. For samples collected at coal mines, the U.S. Mine Safety and Health Administration (MSHA) utilizes the P7 method for respirable quartz analysis. The objectives of this work are to 1) evaluate the performance of the P7 method on field samples of low quartz mass loadings, 2) evaluate the magnitude of dust mass spatial variability within an enclosed cab environment, and 3) estimate the subsequent propagation of error in calculating the per. centage of quartz over a broad range of mass and quartz filter loadings at a surface coal mine. These objectives were achieved by obtaining surface coal mine dust samples over a 9-month time period in enclosed cabs of three drills and three bulldozers. By measuring weighing precision and using reasonable estimates for sampler variability, the dust mass spatial variability component was calculated by difference. The results show that 1) the P7 method can be precise and linear with quartz mass loadings as low as approximately 5 µmg of quartz, 2) the dust mass spatial variability, even within an enclosed cab environment, is the dominant factor of variability in propagation of error in estimating the quartz content of the obtained dust samples on a percentage basis, and 3) weighing precision is not a significant factor in error propagation. In addition to the enclosed cab samples, samples from eight surface coal mine drills were collected at various locations exterior to the drill cab. Significant data scatter at these outside locations strongly suggests that the ambient dust mass spatial variability has a significant effect on the propagation of error in estimating quartz content of the dust samples on a percentage basis.

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly '1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By H. John Head, Fred N. Kissell

In This Chapter [Gas reports from around the world Regulations for gassy mines in the United States Differences between metal/nonmetal mines and coal mines Monitoring for methane and taking action Diluting methane with additional ventilation Eliminating ignition sources What experienced mine operators say about methane control and Looking for methane when starting a new mine or expanding an existing mine] This chapter gives guidelines for preventing methane gas explosions during metal and nonmetal mine development and subsequent production operations.3 Emphasis is placed on recognizing the differences between coal mines, where the potential for methane hazards is relatively well understood, and metal/nonmetal mines, where methane may accumulate unexpectedly. Also, interviews with experienced mine operators add much to a complete understanding of what must be done to address methane problems in metal/nonmetal mines. METHANE GAS IN METAL/NONMETAL MINES Gas reports from around the world. The presence of methane gas in metal/nonmetal mines around the world is more common than one might imagine [Edwards and Durucan 1991]. For example: • The former Soviet republics have occurrences of methane and hydrogen in apatite, gold, and diamond ores, where solid or liquid bitumen occurs in the rock. • Scandinavian iron ore deposits include methane and other hydrocarbons in boreholes that intersect pitch and asphalt within the deposits, and methane and nitrogen in boreholes and fissures in arsenic and sulfide ores.

Jan 6, 2006

By Raymond B. Ladoo

"Domestic Situation:The greatly increased use of lithopone as a base for paints, particularly for interior use, has timulated the demand for barytes to such a degree that the supply cannot keep pace with the demand. Lithopone is an artificially prepared compound composed of about 70 per cent barium sulphate and 30 per cent zinc sulphide, precipitated together. Its most important use is in paint, but it is also used in oilcloth, linoleum, rubber goods, shade cloth, etc.Prior to the war large quantities of barytes were imported from Germany, but during the war imports were negligible, domestic production increased very greatly and is still increasing. Ground barytes as used in paints/ formerly regarded as an adulterant, but now it is generally recognized as a valuable paint constituent. Mile domestic sources have expanded rapidly they have not overtaken the demand and there is need for still greater expansion. Stocks are low, little is being sold on the open market, and prices are high. Since barytes is a gangue mineral associated with metallic ores now being mined in the west, it is suggested that more attention be given to its recovery as a by-product.The following tables compiled from reports of the U.S. Geological Survey and the Bureau of Foreign and Domestic Commerce, indicate the growth of domestic consumption."

Jan 1, 1920

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By William L. Rice

This Bureau of Mines Open File Report on nickel is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign nickel properties and deposits has been abstracted for use in this report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 1984

By John J. Sammarco

The U.S. Bureau of Labor Statistics reports that the mining industry has the highest average annual fatality rate (31.9 per 100,000 workers) among all major American industry. To address this, a major research program to reduce hazard exposure of miners with computer-assisted mining equipment was initiated by the U.S. Bureau of Mines.1 One application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the haulage equipment so that it follows the machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors that can survive the hostile mine environment of dust, methane gas, and water, play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations were conducted to establish operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a sensing system. Various technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications but were found unacceptable. However, a near infrared (IR) sensor employing active targets met the requirements. The sensor has a nominal 75° conical field-of-view and a range from 0.1 to 18.0 m. For the single target mode, nominal range accuracy was 4.3% at a distance of 3.56 m. Correction algorithms were generated reducing the error to 0.6%. Airborne dust testing showed less than 0.8% accuracy (worst case) degradation at levels exceeding (by a factor of 7.5) concentrations permitted by Federal law. The sensor can track multiple active targets providing five degrees-of-freedom (DOF) measurements. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. A guidance system for the haulage system to follow the mining machine does not exist commer¬cially. Such a system can reduce fatalities and injuries by current haulage mining equipment, and is a viable alternative to current haulage control.

The coal-bearing areas of Kansas cover approximately 18,800 square miles (23 percent of the state's total area). Coal in Kansas ranges from lignite to high volatile bituminous, located principally in the south-eastern part of the state. Kansas reserves are estimated to be 987,500,000 tons, approximately 0.2 percent of U.S. reserves. Coal beds generally occur in thin seams up to five feet thick. The overburden-to-coal stripping ratios in Kansas are among the highest in the nation, typically 20 to 1, with some ratios up to 35 to 1. The first commercial coal mining operation in Kansas opened in 1865 at Fort Scott in Bourbon County. As in other states, coal production in Kansas increased during the industrial revolution, and then fell as industry converted to alternative fuels. Production peaked in 1916 and 1917, with annual production of 7,250,000 tons. Coal production today is by surface mining methods. The Kansas regulatory program was approved April 14, 1982; the Abandoned Mine Land Program was approved February 1, 1982; and the emergency program authority was approved January 10,1989.

Jan 1, 1992