Search Documents

By B. W. Gandrud

In 1927 Coghill5 showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling, but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe.

Jan 1, 1934

Provide ear protection which allows normal, unaltered hearing at low noise levels, yet protects the wearer from excessive noise. The Approach: A commercial earmuff with integral speakers has been adapted with a special amplifier so that low sound levels are not affected, but higher noise levels automatically reduced. How It Works: The discriminating earmuff developed by the Bureau of Mines has two modes of operation. In the first mode, where input sound levels are less than or equal to 83 decibels, the wearer will perceive noise at its actual level. For inputs in excess of 83 decibels, the second mode of operation begins and the sound perceived by the wearer is progressively attenuated, or reduced, as the input level is increased. A recognizable difference still exists between two adjacent sound levels enabling the wearer to differentiate between them.

Jan 1, 1975

By Ray J. Holmquist

"INTRODUCTION The Copper King or Red River copper mine was examined on December 13, 1942, by the Bureau of Mines at the request of Richard Kelly of Santa Fe, N. Mex. The examination was made to determine whether the expenditure of funds for rehabilitation work necessary to make the workings accessible for examination would be warranted.As a favorable report was made, the workings of the Copper King mine were opened and sampled under the direction of the author. The portal of the Copper King adit was opened first. Considerable rehabilitation was necessary in the first 50 feet of the workings, but the remainder of the drifts and crosscuts were sufficiently open to permit surveying and sampling.An attempt was made to open the Waterbury atilt, which was reported to be about 30 feet east of the Copper King portal, and to crosscut the ore body nearly to its southern border. However, slide rock and mine dumps had completely obscured the portal of this adit, and no opening into it could be found or made.Work on the project was started on September 27 and vas completed on November 6, 1943."

Apr 1, 1947

By A. A. Giardini

This report represents the results of a literature study on boron nitride and related substances. The purpose of the study was to find Information that might be of value for production of a new, hard modification of boron nitride preferably in single crystal form. The report consists of a review of the major developments in boron nitride research, a discussion of the results, tabulations of physical and chemical properties;, conclusions drawn from the study, and a bibliography.

Jan 1, 1953

By Christopher H. Roe

This Bureau of Mines report reviews the various methods of removing the liquid from tailings slurries that contain very fine grained solids. Gravitational settlement, centrifugation, filtration, and thermal drying methods are discussed in detail. Chemical additives, electrokinetic dewatering, and the rotary trommel screen are also mentioned. Lists of dewatering equipment and suppliers are given in the appendixes to assist the planner who must choose the most efficient, economic, and practical method of dewatering very fine grained mill tailings.

Jan 1, 1984

By C. K. Rose

A hydraulic scaling rig was placed in operation at the Bureau of Mines oil-shale mine near Rifle, Colo., in 1953. The rig consists of a self-leveling platform mounted on a hydraulic-powered boom. The boom is mounted on the bed of a diesel truck. The equipment provides a movable work platform from which two men can work in safety and comfort while barring loose rock from the backs and walls of the rooms, pillars, and haulageways. INTRODUCTION As a part of its synthetic liquid fuels program the Bureau of Mines has developed a mine in the richer oil-shale beds of the Green River formation near Rifle, Colo. An important part of the work of the Oil-Shale Mining Branch is investigation of techniques for low-cost mining of oil shale on a commercial basis. It is evident that scaling loose rock from the high backs and walls of the mine represents a portion of the direct mining cost. This paper describes the development of a scaling rig for operation in the upper heading of the mine, which is 39 feet high.

Jan 1, 1954

Coal miners, especially roof bolter and continuous miner operators, work in a hazardous underground environment where they are often exposed to poor roof conditions. Nearly 500 rock fall injuries are reported each year, and 99% of them are caused by rocks falling from between the roof bolts. These loose rocks that injure miners are usually just a few inches thick, but on average weigh 280 pounds. NIOSH has found that most rock fall injuries can be prevented by installing roof screen during the bolting cycle. Roof screen is a sheet made of steel wires in a grid pattern. When screen is bolted up against the mine roof, it provides far more coverage than any common surface control used in the mines today. Because more mine roof is covered, there is less chance that a rock will fall and injure a miner. The facts about roof screen are shown in the new NIOSH video entitled “Make It Safer With Roof Screen.” Using extensive underground footage, the 7-minute video shows how well screen keeps loose rock from falling in difficult roof conditions. Techniques for installing screen from both outside-controlled and walk-thru roof bolting machines are shown. The video also provides safe handling tips, best practices, and information about machine technology that can greatly improve material handling. Throughout the video, a coal mine safety manager and a shift foreman talk about the tremendous difference that roof screen has made at their mines. An instructional booklet supplements the video with additional information. It presents compelling data from mines that have practically eliminated rock fall injuries with a roof screening program. Other sections of the booklet discuss in greater detail roof screen installation, tips for manual screen handling, a material handling system for roof screen, and use of the personal bolter screen, which can be easily handled by one person. Screen specification and custom ordering are described, including the sizes of screen, grid sizes, reinforcing (indicator) wires, edge cut options, and screen strength. A list of additional sources of information is also provided. Nearly every mine eventually encounters poor roof. Screen is one of the most powerful control techniques available. This new video will help make mine managers aware of screen, and it can help them in developing a roof screen installation program. It also serves as an information source and teaching tool for safety managers and trainers. The video can easily be integrated into new miner training programs or annual refresher training.

Mar 1, 2005

Improve the dust-control effectiveness of the Rotoclone1 dry-dust collection systems used on surface coal mine drills.

Jan 1, 1994

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

By Kevin Connor

The mineral industry in Burundi was a minor contributor to the country's gross domestic product (GDP), which was estimated at just $1 billion for 19812. Coffee and tea continued as the Nation's major export commodities. Mineral exports consisted of small tonnages of wolframite, cassiterite, and baetnasite. Burundi's trade balance of payments situation worsened in 1981, with import payments more than double export revenues. Petroleum imports alone equaled 46% of the export revenue total. By year-end, the only indigenous fossil fuel source to have been found in Burundi was peat, which the Government had been attempting to develop to alleviate some of the petroleum import requirements. In June 1981 the Irish Peat Development Authority, Bord na Mona, signed a 4-year contract with the Burundian Government to supply technical staff for the ongoing peat project work there. Funding for the project was provided by the VS. Agency for International Development and the Government of Ireland. The new contract, which was an extension of ongoing peat research there, represented Burundi's increased awareness of the value of its large peat reserves for both energy and agricultural uses. At yearend, Burundi's Ministry of Public Works and Mines was does to selecting a contractor to study the feasibility of developing Burundi's phosphate deposits. The study would determine the potential for establishing fertilizer production facilities based on the country's phosphate reserves at Matongo-Bandaga, The study's specific objectives are to prove mineral reserve tonnage and grade, draw up mining and processing facility designs, estimate capital and production costs, and conduct a regional market and distribution survey. The cost of the study was estimated at slightly over $1 million, and it should take approximately 16 months to complete. The proposed project will mark the Burundian Government's first step in its plan to exploit on a large scale its natural mineral resources for advancing its agriculture-based economy. Burundi was dependent on imports, which are expensive to transport inland from coastal ports, to supply its domestic requirements for fertilizer. It was planned that part of the fertilizer production from the

Jan 1, 1983

By W. W. Adams, T. D. Lawrence

"The National Safety Competition covering the calendar year 1934 was the tenth yearly safety contest conducted by the United States Bureau of Mines. Participating in the competition were 334 mines and quarries in 38 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies ""Sentinels of Safety.""Since these annual contests were begun 10 years ago by the United States Bureau of Mines the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the prevention of accidents has been achieved, as is indicated by an almost constant downward course in toe accident-frequency rates for the contest group as a whole during the past 10 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the decade and a downward trend during the latter part of the period except in 1930 and 1934; in each of those years a disastrous explosion with abnormally heavy loss of life occurred at the property of one of the participating companies.Because of the abnormal nature of the major disaster in a bituminous-coal mine in 1930 and 1934 the accident-severity rates for the bituminous group for those years are not strictly comparable with the rates for other years. The rates for bituminous mines for 1934 in the present report have therefore been computed on two bases; first, to exclude the record of the company that suffered the disastrous explosion and, second, to include the record of this company. The first rate represents the normal experience of the bituminous coal companies unaffected by the disaster and is therefore more indicative of the real trend of the accident rates for this class of mines from year to year. The latter rate shows the actual experience of all bituminous mines in 1934. The report of the competition of 1930 likewise showed the rates for the bituminous group as computed both with and without the disaster that occurred that year.The National Safety Competition is conducted by the United States Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the facts contained in the accident reports which the competing companies furnish to the Bureau to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest."

Jun 1, 1935

By A. E. Wells

A critical study of the wet Thiogen process for extracting sulphur from the smoke of smelters is one of several investigations related to the general smelter-smoke problem that are being conducted under the direction of the Bureau of Mines. Part of the work done in the pyrometallurgical section of the cooperative metallurgical exhibit of the Bureau of Mines at the Panama-Pacific International Exposition during 1915 related to this investigation, and at the expiration of the exposition, the work was continued in the labora- tories of the Bureau of Mines in the Hearst Memorial Mining Building of the University of California, Berkeley, Cal., where a mining experiment station of the bureau has been established under the cooperative agreement with the University of California. Early in the spring of 1915, when plans were being made to co- operate with several metallurgical interests, the Thiogen Co. proposed to the Bureau of Mines that, along with the studies of various pro- posed methods for eliminating sulphur dioxide from smelter smoke, there should be included a study of the wet Thiogen process. In the study as outlined it was proposed to determine whether it would be technically and commercially feasible to use the, process for the recovery of elemental sulphur from the sulphur dioxide in waste smelter gases. Although there had been no large-scale work with the process, either in the laboratory or at a smelter, representatives of the metallur- gical and mining industry had shown considerable interest in the proposed method, and the desire had been expressed that a better knowledge of the possibilities of the process should be obtained. Thus, cooperation with the Thiogen Co. seemed justified by the in- terests of the metallurgical industry, and by the conservation promised by the recovery of a product of market value from what is otherwise a waste, and in some instances a serious nuisance. In accepting the responsibility for directing this investigation, the officials of the Bureau of Mines were necessarily free to conduct the work in the manner they considered necessary to determine the facts. It was also understood that any information obtained was to be made available to all who might be interested and might be printed in a Bureau of Mines report. To cover the cost of laboratory equipment and supplies, and the payment of salaries of assistants, other than Bureau of Mines employees, the Thiogen Co. in May, 1915, deposited with the cooperative metallurgical exhibit fund a sum considered sufficient to warrant starting the laboratory investi- gation. The origin and organization of this fund has been described by Clevenger and the author." In outlining the program for this investigation it was hoped that ultimately a small complete plant would be erected and the investi- gation center around the operation of the plant. However, pre- liminary to the erection of the plant, a laboratory study of the proc- ess was considered necessary, as the technical features of the process could be determined, it was believed, as satisfactorily on a smaller scale as on the scale first proposed. However, it was realized at the time that it would not be possible to determine so satisfactorily or definitely the commercial possibilities of the process on the scale of work adopted as in the larger operating plant. With this fact in mind it was planned that, if the study of the technical features on a laboratory scale gave sufficient promise of the process being commer- cially feasible, an operating unit should, if possible, be constructed later, and that more definite information concerning the commercial prospects should be determined. The investigations were started in June, 1915. In June and July work was confined entirely to small-scale laboratory tests, in which a careful study of the chemical reactions involved was made. In August, tests on a larger scale were started, and these were con- tinued until December, small-scale tests being made at the same time. On December 1, 1915, all work on the Thiogen process was discon- tinued temporarily, as the close of the exposition necessitated moving the laboratories. Work on the Thiogen process was started again in January, 1916, in the laboratories of the new mining experiment sta- tion at Berkeley, Cal., and was continued during the spring of 1916 until a point was reached where it was felt that the essential parts of the process had been carefully covered, and that some definite state- ments concerning the technical features and possibilities of the process, as given in this report, were warranted.

Jan 1, 1917

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

By Victor E. Kral

"SUMMARYFollowing a magnetometer survey on the McCoy iron deposit, a trenching and drilling program was carried out by the Bureau of Mines in August 1944.This deposit is 32.3 miles southwest of Battle Mountain in the McCoy Mining District, Lander County, Nevada, and lies on the east flank of the Fish Creek Mountains at an altitude of 5,400 feet, about 1 1/2 miles south of the gold camp of McCoy.Total production from the deposit has been 400 tons of magnetite, mined by hand and shipped to the west coast for ship's ballast.Bureau drilled two holes to a total depth of 92 feet and excavated 12 feet of trenches. Both holes were drilled in the same ore body and engineered magnetite ore 14 and 11 feet thick. Trenching was used successfully to show the lateral limits of the ore.Magnetite ore bodies were found to occur as replacements of a limestone bed in quartzite. They outcrop near and parallel to the exposure of a diorite entrusting that forms a long westward-trending ridge. Although magnetic outcrops can be traced for 5,000 feet trenching definitely proved the ore bodies to be disconnected to have little or no lateral extent beyond their outcrops. Only two ore bodies more than 10 feet thick were found; one of these is the inaccessible to and the other was drilled by the Bureau."

Jan 1, 1947

By Robert L. Lagace, N. Albert Moussa

The objective of this project was to perform a preliminary study to determine the desirability/practicality of burying the communication cables in underground mines in order to protect then from the effects of fires and explosions We conducted discussions with Government and industry specialists on the physics of mine fires and explosions, mine disaster fighting, rescue, and investigation activities, and on nine operations. In addition we examined published experimental work and selected detailed NSHA accident reports on fires and explosions in underground mines. We found the overall desirability /practicality of cable burial must be regarded at this time as highly questionable, because of its benefit limitations to special sceneries, its practical operational shortcomings, and the availability of alternative cable protection options.

Jan 2, 1982

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By J. Fletcher Smoak

Consumption of abrasive materials in the United States increased 22% in value over that of 1982 to $320 million; of which, 59% was manufactured abrasive, 35% was industrial diamond (natural and synthetic), and 6% was natural abrasive. Production value of natural abrasives, excluding industrial diamond, remained virtually unchanged. Production of crude tripol, a porous siliceous rock, decreased slightly; however, shipments of processed tripoli increased 13% in quantity and 32% in value. Production of garnet, an abundant iron-aluminum silicate, continued to increase primarily because of further increases in production from one plant that had completed an expansion program in late 1981. Production of special silica stone, both crude and finished, decreased in 1983 because of reduced demand for oilstones

Jan 1, 1984

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

To provide a means for rapidly evaluating proposed mine layouts in order to avoid potential hazards while minimizing loss of coal. The Approach: Development of a computer program that will compute many possible mine layouts by changing the mine plan until the arrangement giving minimal hazards with optimum extraction is found. How It Works: The Hazard Evasion Program for Mine Planning, developed by the Bureau's Denver (Colo.) Mining Research Center, tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on the criteria of maximum safety for workers with minimum abandoned coal), limits the number of choices that need to be considered and appraised for applicability to a given mine scheme. The program is applicable for room and pillar or longwall mining, for oil and gas well hazards, and for other hazards that can be described mathematically such as channel sands, potential bad roof areas, faulting, voids, or water pockets.

Jan 1, 1974

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976