Search Documents

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By L. J. Prosser, Robert Anderson

Advance knowledge of roof conditions can lead to improvement in roof control strategies that will reduce roof falls and ultimately will reduce injuries to mine workers. J.H. Fletcher and Company, in cooperation with West Virginia University, has been developing a system to meet these needs by collecting torque, thrust, and rotation speed data during drilling operations. Recent improvements in analysis algorithms to detect anomalies in the roof structure as well as various display enhancements for real time mapping and evaluation of roof structures have been incorporated into current Fletcher Information Display system. The unit has also been housed in an explosion-proof container to allow use in coal mine applications. Recently, the system has undergone extensive field trials in several limestone mines and one coal mine. During these trials, the National Institute for Occupational Safety and Health assisted Fletcher in verifying the accuracy of the roof mapping capability of the system by comparing the display information to bore hole scoping observations and drill corings. It was concluded from this assessment that the intelligent drilling system can complement scoping and core analysis to provide a more complete picture of roof strata and is capable of seeing features or conditions that are not always obvious in these more traditional methods.

By L. Nahai

Overall mineral industry productive activity in Europe increased in 1965, following general upward trends in gross national product and total industrial production4 recorded. The gross national product of non-Communist Europe in market prices in 1965 was estimated at $572 billion and that of Communist Europe at $409 billion. However, the extractive sectors of the mineral industries generally did not fare as well as the processing sectors. In fact, a number of countries recorded lower production levels in this sector in 1965 than in 1964 and most countries had a lower growth rate in extractive industry output than in overall industrial output. Among the non-Communist nations of Europe, a general decline in coal production and lower levels of iron ore output in France, West Germany, and Luxembourg contributed significantly to the smaller growth rates or declines in extractive indexes. Where higher indexes were registered, this generally resulted from the performance of the petroleum and natural gas industry; exceptions were Greece, Norway, and Sweden. The decline recorded for Czechoslovakia was attributable entirely to poorer performance by that nation's coal industry.

Jan 1, 1967

Reduce injury to people or damage to equipment when a scheduled production blast is detonated. Approach The essential elements of an effective blast area security system were identified through case studies of five mining operations where the blast area guarding practices were considered to be superior to those generally found in the industry. These elements were used in making recommendations for improved blast area safeguarding practices. Background The blast area security system is a means by which the mine operator prevents injury to people or damage to equipment when blasting is performed. Analysis of blasting accidents showed that most blasting accidents occur during scheduled blasting and are due to inadequate blast-site security. Factors contributing to the system's breakdown are failure to clear the blast zone, inadequate guarding. and failure of personnel to follow instructions, retreat to a safe location, and/or take adequate cover. Mine personnel, visitors and even trespassers can inadvertently wander into a blasting zone unless proper procedures exist to ensure that all personnel are cleared from the blast zone and kept safely away until after blasting IS completed. Statistics show that the blaster is the miner most frequently injured In these accidents.

Jan 1, 1986

By W. E. Webb, R. H. Church, W. G. Hopkins

The development of systems for location of miners who have become entrapped following a mine disaster has been one of the major research goals in the Bureau of Mines. This study details the preliminary development of such a system. Current technologies for locating trapped miners from the surface are either simple direction, finders or time difference pulse systems that have accuracy Limitations. Developing technologies using full vector field measurements at several receiving points are currently being studied. The necessity of measuring field strength with great accuracy can be a drawback in these systems. A system that operates with continuous wave radio signals, whose phase differences can be measured accurately even in weak signal conditions, greatly improves the location accuracy. A microcomputer would be used, in conjunction with the system, to gather and manipulate the data to automatically pinpoint the location of the trapped miner. Comparison of this system with existing technology indicates a favorable accuracy/complexity ratio for the phase difference of arrival technique.

By J. Roger Loebenstein

Small amounts of arsenic trioxide were shipped in 1988 from remaining stocks at ASARCO Incorporated's closed plant at Tacoma, WA. Imports of arsenic trioxide were at about the same level in 1988 as in the previous year. Legislation and Government Programs The Occupational Safety and Health Administration (OSHA) levied a $1.6 million fine against Asarco for exposing its workers at its East Helena lead smelter in Helena, MT, to unacceptably high levels of lead and arsenic. The bulk of the fine was for violations of a respiratory protection program. The same smelter and its environs has been listed as a Superfund toxic-waste site by the Environmental Protection Agency (EPA). Tests had shown high levels of lead, cadmium, and arsenic in the soil near the smelter. EPA planned to extend the cleanup to areas within the town of East Helena because high levels of arsenic had been found in shallow test wells outside the smelter site. Federal and State health officials have warned residents living in the vicinity of East Helena to avoid eating certain home-grown vegetables because of high concentrations of heavy metals.2

Jan 1, 1990

Develop a lightweight, portable device for use in mines for non-destructive testing of resin grouted roof bolt bond integrity. Approach A unique, intrinsically safe, electronic instrument has been developed that determines the holding quality of a fully grouted roof bolt by testing the integrity of the resin bond to both the bolt and to the surrounding rock. How It Works A measured pulse of energy Is sent Into the bolt by a piezoelectric transducer, and the instrument listens for reflected energy. Where the bolt is properly bonded, the energy passes from the bolt, through the resin, and out into the rock mass. Where proper bending does not exist, a portion of the energy Is reflected back along the bolt. The Instrument measures the reflected energy and compares it to the original pulse. The amount

Jan 1, 1982

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 32,270-hectare Cache Peak study area in 1992; the area had been proposed as wilderness. Bureau personnel examined and sampled prospect workings; 50 rock and placer samples were taken during the investigation. The study area is centered about 25 km southeast of Challis, Idaho, in the Challis National Forest. According to May, 1993, Bureau of Land Management mining claim records there were no current mining claims located inside the study area. Up to 100 claims may have been located in the study area in the past. Gold, silver, copper, lead, zinc: Significant analyses, poor exposure precludes resource estimate. Limestone: More than I billion tonnes may be chemically suitable for a variety of uses, markets too distant to favor mining. Dolomite: More than 1 billion tonnes may be chemically suitable for producing magnesium metal, markets too distant to favor mining. Sand and Gravel: Several million m3, but markets and transportation costs do not favor mining. Chalcedonic nodules: Two localities in the study area may be of interest to hobbyists who cut and polish stone. There is no reported past production from the study area.

Jan 1, 1993

To improve efficiency in producing clarified water from mineral and metallurgical processing streams containing suspended particles. Approach Particles suspended in mineral and metallurgical processing streams are filtered out by granular magnesium oxide (MgO) used as the medium in deep bed filters. How It Works MgO is substituted for the silica sand or garnet sand currently used in conventional deep bed filters. These filters presently consist of a 24- to-48-inch-deep layer of either silica sand or mixed media, consisting of a stratified combination of anthracite coal, silica sand, and garnet sand. As waste water containing fine solids is percolated through the granular bed, the suspended particles become attached to the filter grains. When MgO replaces sand as a filter medium, the overall filter capacity is generally increased 50 to 80 percent, and no equipment modifications are necessary for filter operation. MgO is unique because it has a positive surface charge in water while most suspended materials are negative. The attraction of these negatively charged suspended particles to MgO enhances filtering performance. As is necessary for all good media, MgO is insoluble and nontoxic.

Jan 1, 1983

Develop new technology to encourage domestic processing of automobile catalytic converters for recovering platinum -group metals. Background Automobile catalytic converters are used to convert pollutants in automobile exhaust into water vapor, carbon dioxide, and nitrogen, About 1 million troy ounces of platinum-group metals arc used each year in the. United Slates to manufacture catalytic converters. It has been estimated that about 60 pct of the used catalytic converters arc being collected. Most of these used catalytic converters were not processed in the United States but were exported to Japan or Europe for processing. In 1991, about 250,000 troy ounces of platinum-group metals were recovered from scrap catalytic converters collected in the United States. Each short ton of decanned catalyst may contain 30 troy ounces of platinum-group metals valued at over $15,000. Development of an economic process for the recovery of platinum-group metals that can be operated on a small or large scale may increase, the percentage of catalytic converters collected and encourage domestic processing to recover a platinum-group metal concentrate. This would significantly decrease the dependence of the United States on imports for these critical and strategic metals.

Jan 1, 1992

By E. C. Lane

"INTRODUCTION This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36 3/. The second resort gave the same data for motor gasolines sold during the summer of 1936 4/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-37 5/.This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others."

Dec 1, 1937

By Suzann C. Ambrosio

The mineral industry in Burundi continued to be a minor contributor to the 1980 gross domestic product (GDP) estimated at $293 million in constant 1970 prices.2 Mineral export revenues, primarily from cassiterite, increased by a factor of 15 between 1979-80, reaching approximately $434,000 by yearend 1980. Gold, bastnasite, colombite-tantalite, and wolfremite continued to be exploited on a small scale, using manual and semimechanical methods. Despite a sharp decline in mining activities during 1979, attributed to a lack o? profitability and shortage of construction materials, the mining sector exhibited signs of recovery during 1980. The mineral exploration budget grew 32% over 1979 levels and was equivalent to approximately $42,000 in 1980. In addition, the Burundi Geographical Institute (IGE BU) was created in September 1980 and given responsibilities to collect cartographic, topographic, hydrogeologic, and other geomorphological data., SONIBUROM, the Burundian and Romanian Government joint mineral corporation, conducted mineral deposit inventories during 1979-80 and has been charged with exploiting some of these as yet unspecified resource areas. Another Burundian-Romanian effort, called Mabaya-Butahana, was initiated to search for gold deposits. Meanwhile on the Ruzizi plain, alluvial gold prospecting, with an estimated grade between 0.2 to 1.0 gram per ton, was carried out on a small scale.

Jan 1, 1982

By N. F. Le Jeuns

For a number of years the Bureau of Mines has conducted semi-annual surveys to determine the changes in motor gasoline being sold in the United States. It was pointed out in the previous survey that there was an apparent tendency toward greater uniformity in the character of gasoline marketed in the United States. This practically uniform tendency which continued from April, 1917 to January, 1923, has been interrupted in the, present survey, as shown by an examination of the column marked "Difference," as given in Table 1. The figures in this table were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10% ,(85 samples) having the highest end points and the 10% having the lowest end points mere grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10%" and the ?Minimum 10%? respectively. The same process was used on the other surveys.

Jan 1, 1923

By John B. Shutack

In an effort to improve the performance of the explosive-anchored rock bolt, the Bureau of Mines studied the effect of the detonation velocity of the explosive and type of charge (linear or nonlinear) on the fracturing tendency of the anchor tube. Also, different types of tubing were compared to determine the one most suitable for use as an anchor tube. The Bruceton up-and-down method was applied in tests in which steel shooting blocks having boreholes ranging from 1-3/8 to 2-1/8 inches in diameter were used. Of the four types of tubing evaluated, a welded A-178 tubing that was drawn over a mandrel and renormalized gave the most promising results. The A-179 seamless tubing that is normally used with the explosive bolt was the most inferior. Both types, however, gave significantly better anchorage than the conventional shell when tested in both laboratory and underground experiments. Within the range of velocities studied (5,000 to 7,000 m/sec), the type of explosive showed no significant effect on anchor-tube performance. In general; linear explosive charges provided better anchorage than nonlinear charges.

Jan 1, 1968

By N. A. Eilertsen

This report describes field investigations conducted in 1953 of two occurrences of manganese and a separate magnetic anomaly in the Southern manganese district of Aroostook County, vicinity of Houlton, Maine -the Pierce deposits, in Hammond Plantation Township; the Burnham anomaly, also in Hammond Plantation; and the Nickerson-Farm prospect in Hodgdon Township. The manganese occurs in a thinly laminated sedimentary rock containing manganiferous carbonate interlayered with fine-grained metamorphosed sediment, rich in chlorite or hematite. The surrounding rocks are mostly dark gray-green slates. Samples composited for metallurgical testing from the Pierce deposits and the Nickerson-Farm prospect assayed 9.0 to 12.3 percent of manganese. More than 90 percent of the manganese could be extracted with sulfuric acid, but in most instances 30 to 40 percent of the iron was also extracted. Leaching tests indicated that, after being reduced in a hydrogen stmosphere at 600° C., about 85 percent of the manganese could be selectively extracted by a solution of ammonia-ammonium carbonate with iron extraction of only 14 percent.

Jan 1, 1958

By K. P. Wang

SIGNIFICANT general developments took place in the Far East during 1964, with far-reaching repercussions on the mineral and industrial economies of individual countries and the region as a whole. Japan, during this, "the Year of the Open Door," ushered in the era of industrial maturity, greater independence in economic policy, and expanded technical assistance to less developed countries. Symbolic of its dynamic economic growth is the fact that Japan out-produced the Federal Republic of Germany in steel during 1964 to take over a third-ranking world position. Mainland China, recovering from the "Leap Forward" debacle, made significant gains in industrial output. Mainland Chinese trade with Japan was on the upswing, and discussions were held between the Chinese and the Soviets for possibly resuming Soviet aid in industrial and mineral development. Meanwhile, United States aid to Taiwan was being phased out because of progress achieved. Rapprochement between South Korea and Japan was imminent late in 1964, a factor which may well affect South Korean mineral development. The Indonesian-Malaysian confrontation created economic difficulties in both countries. The war in Viet-Nam seriously disrupted industrial activities, particularly in the south.

Jan 1, 1966

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

By E. J. Babcock

The existence of vast deposits of lignite in the West Central and Western States is well known, although the extent and importance of the deposits have not been appreciated, nor has there been an adequate economic utilization of the deposits. The work of the Bureau of Mines, the United States Geological Survey, and the State geological surveys is disclosing an increasingly large area, underlaid with this kind of coal. Among the States having the largest workable deposits may be mentioned North Dakota, Montana, Wyoming, Colorado, and Texas, and in several other Western States lignite occurs in smaller areas. In North Dakota alone it is estimated that the deposits cover approximately 32,000 square miles, many of them being 10 to 15 feet thick and capable of producing in all several hundred billions of tons of lignite. When one stops to consider what these figures mean as to the immensity of these deposits in the West, it is not strange that people are seeking to ascertain better means for deriving larger benefits from the proper utilization of those great deposits. Consequently, any proposed methods of utilization that are promising are well worthy of careful consideration.

Jan 1, 1915