Search Documents

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

Accurately measure time of detonation and explosive detonation velocity in a blasthole for analysis of explosive performance and delay intervals. Approach A blasthole-monitoring fiber optic probe was developed consisting of filer optic cable to carry the fight and a sensor to detect and convert the light signals into electrical signals. Events can then be recorded on an oscilloscope, tape recorder, digital computer, or start-and-stop timer. This method is simpler to use and more immune to electronic noise than existing resistance techniques. The fiber optic material,, are inexpensive and easy to obtain, and the recording devices, such as storage oscilloscopes, arc available or easy to obtain. The probe provides the mining industry, explosive manufacturers, and those studying blasting, with a practical alternative to complex and expensive coaxial cable reflectometry, resistor strings, or resistance wire methods for determining explosive and detonator performance. How It Works The fiber optic cable is a plastic light guide consisting of sixteen 0.01-inch-diameter optic strands having an overall outside diameter of 0.087 inch. The receiver module incorporates a photodiode to detect the signal and an integrated circuit receiver for signal amplification into one package about 1/2 by 5/8 by 7/8 inch.

Jan 1, 1989

By Walter E. Pittman

This Bureau of Mines study surveys the current state of technology and the various research efforts that have been undertaken to dewater the dilute phosphatic clays generated in the production of phosphate rock. The research described includes early dewatering experiments, fundamental studies of clays and of flocculation, and minor dewatering techniques such as freeze-thaw methods, the ANDCO process, moving screens, sand wick, crust development, and overburden pumping. Some methods that are currently being evaluated are described. They include the Estech sand-clay mix process using the Enviro-Clear thickener, sand-clay sandwiching, dredge mix, dredge process, and the sand-spray process. Developing technology for dewatering phosphatic clays also is described, including the Bureau of Mines rotary trommel method and the Gardinier process.

Jan 1, 1984

Capture airborne coal dust generated by a continuous mining machine to reduce workers? dust exposure and to improve face visibility. Approach Develop a low-profile dust collector system which can be mounted on the boom of a continuous miner. How It Works When coal is mined with a milling head continuous miner, a substantial amount of coal dust (respirable and non-respirable) escapes the dust suppression sprays at the cutter head. This can cause poor visibility around the cutting head and can expose the workers to high levels of respirable dust. A practical means of removing this dust is with a scrubber mounted directly on the mining machine. Under a Bureau of Mines contract, a low-profile, machine-mounted dust collector (MMDC) was developed to avoid adding extra height to the continuous

Jan 1, 1983

By John R. Benham

The Long Swamp RARE II area contains no prospects, claims, or mines. It has a low potential for ore deposits. There are no geothermal, oil, or gas leases in the area. APPRAISAL There are no mining districts in the study area. The nearest is Chewack Mining District, which is 6 mi (9.6 km) north of the area. This district had numerous claims located for tungsten; the principal tungsten ore mineral was wolframite. Wolframite was found here in 1898 by surveyors of the International Boundary Commission. The area was staked in 1908 and developed during 1915 and 1916. Only in 1936 was ore shipped; the 30 ton (27.2 t) shipment proved to be unprofitable for the claimants (Culver, 1945, p. 41).

Jan 1, 1982

By C. B. Manula, R. L. Sanford, R. A. Rivell

The large amount of computer code required for this simulation model dictates that reasonable limitations be placed on some of the input variables. The program permits the following maximum sizes: 1. Ten mine car stations 2. Twenty track intersections 3. Three hundred mine cars 4. Eight motors 5. One hundred profiles 6. Twelve intersections between stations 7. Forty-five profile changes between stations 8. Thirty station pairs (routes) These may be changed by the user providing the particular computer in use has available core storage. Major Array Descriptions This section is a detailed description of four of the major arrays used in the rail haulage simulator for data storage and logical control. Other arrays are used; however, they may be considered sub¬servative to the major ones. These major variables are explained on the following pages. Motor Control Array (XXXDEF). The first 99 locations in this array are arranged according to and are developed by data input. Unit conversions are made at input time which include: 1. Tons to pounds. 2. Rolling resistance in pounds/ton to percent/100. 3. Miles per hour per second (mphps) to feet per min. per minute. 4. Miles per hour to feet per minute. The following information is stored for each motor at the array

Jan 1, 1974

Improve the efficiency of stainless steel pickling (chemically cleaning) operations by providing the industry a quick and convenient method to estimate pickling solution behavior and to estimate recommended ranges of nitric and hydrofluoric acid concentrations for effective pickling of stainless steels. Background Iron, chromium, and nickel in stainless steels react with nitric and hydrofluoric acids during pickling. Ions of these dissolved metals complex or combine with the acid anions. When the total metal concentration reaches about, 50 grams per liter of pickling solution, the solution no longer serves its purpose and is considered spent. Knowledge of cation and anion species in these pickling solutions contributes an insight into pickling chemistry and allows estimates to be made of the most effective ranges of acid concentrations. The Bureau developed a computational model of the complex equilibrium chemistry occurring among iron, chromium, and nickel and the pickling solution. Total concentrations, in grams per liter, of nitrate, fluoride, iron, chromium, and nickel were used as input; output was 17 cation and anion molar concentrations. The model, in the form (if an equilibrium program on a mainframe computer, was used extensively to facilitate Bureau research by determining chemical complexes in numerous stainless steel pickling solutions. However, the program's availability to members of the stainless steel industry, its intended users, was limited because of lack of mainframe compatibility and the difficulty of program maintenance.

Jan 1, 1989

By A. Mayton, A. Brien, W. Porter, O&apos

In 2004, management at Unimin's Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In 1981, the combined value of these commodities accounted for about $11.6 million,2 over 85% of the total value of mineral output. Production of cement, sand and gravel, and quarry products increased substantially above the 1980 level. Mining bated on gold production was decreasing, and employment in the industry was declining. The better grade deposits in the one active mine were worked out, and only another 10 years' production at current rates was estimated to remain. While the high world gold price of 1979-80 led to intensive exploration, there has been little sum.

Jan 1, 1983

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By Suzann C. Ambrosio

Crude petroleum, the only commercially exploited mineral resource in Cameroon, continued to dominate developments in the mineral industry sector. International mining concerns have expressed interest in developing Cameroon's bauxite and iron and steel potentials. Domestically, the mineral industry focused on production of fertilisers for agricultural development, infrastructure construction, and hydrocarbon development, through the nearly self-sufficient production of fertilizer materials, cement, and crude oil. The mineral sector contributed 5.6% to the estimated 1981 gross domestic product (GDP) of $6.5 billion.2 Petroleum exports accounted for approximately 4.5% of the 1981 GDP and exceeded coffee and cocoa exports for the second consecutive year. The trade gap widened during the fiscal year ending on July 80, 1981, owing to a 21% increase in exports and a 25% increase in imports. Offsetting these balance-of-payments difficulties, typical of developing countries' early economic stages, were increases in foreign exchange reserves to $71 trillion by May 1983.

Jan 1, 1983

By S. R. B. Cooke

Certain saturated and unsaturated fatty acids and a variety of resin acids were used as collectors for specular hematite, magnetite, and goethite. Vacuum flotation tests were used with each collector and mineral to delimit the fields of flotation and nonflotation as functions of concentrations of collector and of hydrogen ion. The experimental results of these tests lead to the following conclusions. The respective fatty and resin acids exhibit characteristic fields of flotation and nonflotation for the three iron oxides. The fields are somewhat similar, and specular hematite apparently is the most floatable mineral. The insolubility of some of the organic acids may seriously restrict flotation at low pH, although the saturated fatty acids, caprylic and capric, collect minus-100, plus-150-mesh specular hematite only in acid pulp. The presence of a lower "critical pH" is explained on the basis of the dissociation and hydrolysis of dilute soap solutions.

Jan 1, 1959

To address the safety of programmable electronics-based mining systems before this technology proliferates in the mining industry.

Jan 1, 1999

By Donald P. Tuchman, Robert P. Vinson, Linda J. McWilliams, Steven E. Mischler, Jon C. Volkwein

A personal dust monitor (PDM) was developed to measure respirable coal mine dust mass to provide accurate exposure data at the end of a work shift. Additionally, the new monitor continuously displays near-real-time dust exposure data during the shift. The PDM uses a tapered-element oscillating microbalance to measure the mass of dust deposited on a filter and continually displays the cumulative exposure concentration data. The accuracy and precision of the instrument was determined by comparison to gravimetric filter samplers in the laboratory and in four mines. Laboratory results with different coal types and size distributions showed that there is a 95% confidence that the individual PDM measurements were within ±25% of the reference measurements. Mine test results indicate that data taken with adjacent PDM and reference samplers are indistinguishable. The technology proved durable enough to successfully measure 108 shifts of data out of 115 attempts in the mines. Under these specific test conditions, the PDM demonstrated that it was convenient to wear, robust, provided accurate data, provided timely data that could be used to prevent overexposure, and was easy to use.

Jan 1, 2004

By Zachary J. Fink

A continuous-monitoring system has been developed for analyses of mine gas concentrations associated with spontaneous combustion, mine fires, and explosive and toxic levels. The analysis center, which is linked to sample locations by polyethylene tubes in bundles, has been successfully field tested by the Federal Bureau of Mines for analyzing carbon monoxide and oxygen; a computational scheme has been developed to process the data at the site. This report contains information on the design, purchase, installation, and maintenance of the tube-bundle system. A brief comparison of the tube-bundle system with the underground-analysis system and plans for future research are also included.

Jan 1, 1975

By Russell C. Frith, David C. Oyler, Dolinar Dennis R., Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures. To help determine what factors contribute to such failures, a comprehensive international database of 131 case histories has been compiled. The cases include six failures where major rock falls occurred in front of the shields, and seven even more serious failures involving major overburden weighting. The case studies suggest two types of room failure mechanism. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender or remnant longwall panel narrows. The second is an overburden weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rockwell above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used. Weighting failures were not greatly affected by the density of roof reinforcement. In one of the overburden weighting cases, in a Pittsburgh coal bed mine, stress cell, convergence, bolt load and extensometer data have been used to analyze the failure in detail. Key words: coal mining, ground control, longwall, recovery room.

By Richard W. Lewis

Domestic production of greensand (glauconite) increased 15 percent in quantity and 13 percent in value compared with that of 1964. Since only two firms were in operation, statistics on production and sales for the year are not reported in order to avoid disclosure of individual company confidental data. The average annual production for the 5-year period 1961-65 was 4,306 tons valued at $200,200. The material was marketed for use as a soil conditioner and a water softener. An article of mineralogical interest was published concerning the New Zealand glauconites.2

Jan 1, 1966

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference index with abstracts of all pertinent literature. A particular strawman system design analysis is included for the Helvetia Coal Co. Lucerne #8 mine in the Upper Freeport seam.

Jan 7, 1979

By Thomas V. Falkie, R. Venkataramani

The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. The variables to be measured were based on the postulated character¬istics of the loading function, as described in the previous chapter. One class of variables presumed to influence the loading function are geological variables. Accordingly, the sites for data collection were selected in different bituminous coal seams at dispersed locations in order that variation in geological conditions would exist. Seven mines in central and western Pennsylvania and one mine in northern West Virginia were selected as data collection sites. Five different coal seams were represented by these mines. The remaining classes of variables - geometric, mechanical, and procedural - were measured as they occurred in the mines. A description of the measurements, and the conversion of these measurements to forms which could be-analyzed for effect on the loading function is given. Mining Dimensions At the underground working face, the following dimensions were measured: a. Thickness of coal excavated. b. Thickness of shale excavated. c. Total height excavated. d. Width excavated. e. Depth of penetration of each machine cut. With the exception of the last of these dimensions, all were measured

Jan 1, 1972