Search Documents

The REL of 1 mg/m3 for respirable coal mine dust does not assure a zero risk for the development of occupational respiratory diseases among all miners exposed during a full working lifetime. Consequently, a medical screening and surveillance program that includes initial and periodic chest X-rays and spirometric examinations is important for the early detection of disease and the prevention of "material impairment of health or functional capacity" [30 USC 8 11(a)(6)(A)]. The medical screening and surveillance program is also useful for disease surveillance, which includes the tracking trends, the setting of prevention and intervention priorities, and the assessment of prevention and intervention efforts. NIOSH encourages both underground and surface coal miners to participate in the medical screening and surveillance program.

Jan 1, 1997

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the char-coals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

Provide an instrument for continuous remote monitoring of carbon monoxide concentration in underground mines. Approach A carbon monoxide fixed? point continuous monitor consists of two modules. A line-powered control module is designed to power a remote transducer module; provide continuous readouts, visual and audible alarms, operational checks; and activate fans and equipment shutdown circuits if preset CO concentration levels are exceeded. How It Works The control module must be used in conjunction with a single transducer module. Developed under contract. the control module is a wall-mounted Instrument which contains a readout and alarm capability and power supply

Jan 1, 1981

By J. D. Dixon

The Bureau of Mines investigated the principles of support-rock interaction, based on structural matrix methods which permit mathematical formulation of the problem and computer solution. The principles are given under two main sections: the first discusses the idealization of the tunnel support structural system for matrix analysis; the latter discusses the analysis procedures necessary for carrying out the solution. A general frame matrix computer program and a medium-size computer should be sufficient for carrying out the procedures involved. The example problem consists of a circular tunnel support which is subjected to a uniformly distributed vertical load, Three wall thickness-radius ratios are studied in combination with four support-rock modulus ratios. This problem illustrates the main procedures of the support-rock interaction analysis involved, and examination of the results reveals the influence of the relative rigidities of the support and the rock.

Jan 1, 1971

Reduce costs of surface mine reclamation by improving scaper operating efficiency and reducing tire costs. Approach The Wheel Slip Monitor senses and compares the peripheral speed of a scraper's four tires 10 the true ground speed of the scraper, and alerts the operator if any of the tires exceeds a predetermined amount of slip. This system helps scraper operators reduce wheel slip during the loading cycle, thereby improving the loading efficiency of the scaper and reducing tire wear and damage. How It Works The system consists of five ultrasonic doppler velocity-sensing devices for measuring the speed of each wheel as well as the true ground velocity (see photograph). Each sensor produces an electrical output signal having a frequency proportional to the speed of the tire or terrain. The signals are conveyed through electrical cables to a control box in the operator's cab where they are converted to voltages proportional to individual wheel speeds (see photograph). The signals are further processed to activate a blinking red light, corresponding to any individual wheel which is slipping, and to sound a beeping tone that is audible to the scraper operator. The rate at which the light blinks and the tone beeps is proportional to the degree of slip. Alerted, the operator can take corrective action.

Jan 1, 1985

Table 1.-Aden: Production of mineral commodities [ ]

Jan 1, 1967

By C. A. Komar

Hardness, tensile strength, and impact toughness of dry and brine-saturated sandstone specimens were measured at ambient, cryogenic, and elevated temperatures as a measure of the relative stability of reservoir rocks for subsurface disposal of liquid wastes. Hardness measurements were inconclusive. Tensile strength and impact toughness were significantly higher at -320° F than at ambient temperature, but were relatively unaffected at 700° F. Impact toughness was reduced by subjecting the specimens to three cycles of rapid temperature changes (thermal shock) over a 1,000° F range. Tensile strength of brine-saturated sandstone was less than that of dry sandstone. Based on results of the tests, reservoir sandstone likely would be stable if exposed to extreme temperatures of liquid wastes, although rapid changes in waste temperatures should be avoided.

Jan 1, 1971

By Richard E. Dawes

Physical variables, a principal factor in the economies of mineral production, affect both capital and direct operating costs. By using a revenue-cost system for the framework, the analyses of revenue and cost categories demonstrate the relative importance of groups of physical variables, whether explicitly defined or not, to a lead-zinc mining operation. Physical variables affecting the producer represent about 60 percent of the total system influence as expressed by cost ranking. Other physical variables affect the remaining costs as controlled by the smelter, the transporter, and the landowner. Such resource conservation aspects as mineral losses due to mining method and mineral processing constitute a portion of the total revenue effects of physical variables. The physical variable revenue-cost system presented in this report offers a framework for cost-benefit analysis of mineral related research.

Jan 1, 1969

By James A. Powell

The theory of electromagnetic fields indicates such fields could be used to detect and locate trapped miners. To be useful, the hardware of the system must meet a number of requirements, including small size, intrinsic safety, and rugged construction. Such hardware has been built, and the system has been tested by the Bureau of Mines and its contractors. These tests indicate that the electromagnetic method provides a practical means to locate miners in emergencies.

Jan 1, 1976

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

By Howard E. Parkinson

Since 1969, the Department of Interior, Bureau of Mines, has carried out communications research. Research has been directed toward developing emergency and nonemergency mine communications. This paper gives an overview of the progress made in the last two years. Particular emphasis is given to the overall program, noise and signal measurements, systems studies, guidelines, products, and demonstrations now being carried on in operating mines.

By Gordon L. Kinney

Following a year of great uncertainty, the political situation in Bangladesh improved during 1976. The major problem for Bangladesh remained the high birth rate and crowded conditions. Bangladesh had the highest population density of any agrarian country--over 80 million people in a land area of 144,000 square kilometers, 65% of which is considered arable. The Government, with considerable foreign assistance, was actively encouraging voluntary family planning, and set a growth rate target of 2% per year or less. However, even if the growth rate was reduced to the target level immediately, the population of Bangladesh would nevertheless nearly double within 20 years.

Jan 1, 1980

By D. Harrington

"The fire boss in coal mining and the shift boss in metal mining, though held responsible to a large extent for safety of underground employees and of the mine, are, it seems to me, not always vested with sufficient authority nor given compensation commensurate with their duties. The metal-mine shift boss, although his position as regards his relations between employer and employee, is frequently an unenviable one, has as a rule much more authority than the fire boss and is not expected to perform the menial tasks required of the latter by many coal-mining companies.In most coal-mining States the coal-mine foreman and the fire boss are re¬quired to possess a certificate of competency obtained by passing an examination. The foreman is legally responsible for the safety of the miners, as in most instances the superintendent is not required to pass an examination. Although the foreman is held legally responsible for the safety of the miners, the law does not, in general, compel the superintendent or other higher officials to delegate sufficient authority to the foreman to enable him to put his wishes or judgment into effect; and this condition has tended in many instances towards perpetuation of unsafe conditions.The fire boss is held legally responsible for conditions in his ""beat"", but he is generally given only such authority as the mine foreman sees fit to delegate, frequently very little, Moreover, the fire boss is generally required to cover his ""beat"" within two hours before the entrance of the underground workers. Only too often his territory is so great that in order to reach all the working faces and chalk the required date at the face, he must travel at a rapid walk or even run. When such haste is necessary to cover the required ground, it is manifestly im¬possible for the fire boss to make a careful inspection or examination of the roof, timbering, wiring, gas, etc., at each place, and doubtless in his hurry many unsafe conditions escape his notice."

Sep 1, 1920

By Henry D. Hibbard

The object of this report is to give briefly information of present value relating to the manufacture and uses of the various commercial alloy steels, with the hope of stimulating the demand for such steels and extending their practical use. The report is issued by the Bureau of Mines as a contribution to the increase of efficiency in the preparation and utilization of the mineral resources of the United States. Alloy steels are included in the so-called special steels, but as the latter term is often used in the mills to designate broadly any steels intended for purposes other than those served by the regular product, it has seemed best to use the more specific term of alloy steels in this report. Alloy steels are bringing about a series of revolutions in various in- dustrial fields in which steel plays an important part. Most elements that could be procured in sufficient quantity have been alloyed with iron in various proportions, either alone or in combination with others, in the search for useful alloy steels. Those steels that have gained and maintained for themselves a place in current use are discussed in this report. Some of them have had an ephemeral life of usefulness which would no doubt have been prolonged had not some other more satisfactory steel been developed. Probably the first useful alloy steel was Mushet's self-hardening tungsten tool steel, patented in 1868. Fifteen years later chromium steel, really containing chromium, was struggling for recognition for some purposes, the chief of which was for the manufacture of solid shot for piercing armor. In both of these steels the effect of the alloying element as used was in a way proportional to the amount contained. In 1882 Hadfield made his epoch-making discovery of manganese steel and demonstrated that in iron metallurgy it is not safe to take for granted anything as to the properties of an alloy of iron with other elements, basing one's opinion on past experience and knowledge, and that the effect of an alloying element may not be proportional to its content. The development of useful nickel

Jan 1, 1915

By R. W. Dalzell, Fred N. Kissell, J. L. Banfield, M. G. Zabetakis

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By J. E. Zeilinger

This Bureau of Mines study was conducted to determine the sulfur reduction potential attainable when washing fine-size coal on a spiral concentrator. Crushed samples of Middle Kittanning and Bakerstown bed coals washed on the spiral provided pyritic sulfur reductions of up to 90 percent for the plus 200-mesh material. Pyritic sulfur reductions on the minus 200-mesh material seldom exceeded 30 percent; consequently, this material would require further treatment. The capacity of the spiral was 2 tph per unit when washing l4-mesh by 0 coal. The ability to remove pyrite combined with the higher-than-expected capacity makes the spiral worthy of consideration as a rougher-cleaner in new fine-coal desulfurization circuits.

Jan 1, 1976

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

Reduce the hazards to which mine personnel are exposed by providing safer procedures for removing dragline wire rope terminations. Background The termination points of wire ropes used on draglines consist of a wedge and socket that lock the rope in place through friction. These components must be separated when the wire rope is changed. At present, the cannon method is the most common procedure used to accomplish this. However this method, using a small cannon and primer (detonator) cord to propel a steel projectile that will knock the wedge out of the socket, has the potential of causing injuries to mine personnel and damage to equipment. The Bureau of Mines, has devised safer, and equally efficient methods of removing wire rope terminations. The Bureau began by studying the cannon method, its merits and draw-backs. Safety guidelines were then developed for the cannon method, and two alternative methods-the pendulum ram and hydraulic pusher-were devised and tested. The Cannon Method The steel projectile used to separate the wedge and socket in the cannon method was found to be very effective. However, the method poses the inherent hazards of any explosive de-vice-hazards that could be increased by lax work procedures. There is no strict uniformity in the manufacture of the cannon or in the work procedures used in the mines employing it. Hazards could be reduced, or even eliminated, with adaption of certain manufacturing and work-procedure guidelines, such as 1) making the cannon and projectile de-signs, as well the work procedures used, uniform, 2) ensuring separate loading of the charge and detonator with insertion of the detonator through a separate port, 3) connecting electrical firing circuits only after the charge and projectile are loaded and the cannon is placed in its final firing position, 4) using approved detonating devices, 5) anchoring the cannon before firing and, 6) placing armor netting over the cannon before detonation.

Jan 1, 1986

By Suzann C. Ambrosio

Cameroon's mining industry continued to be dominated by crude petroleum. The value of petroleum output was estimated at $1 billion.2 The 1982 gross domestic product (GOP) was approximately $8.4 billion. During 1981, crude oil export revenues increased in value 30%, comprising approximately 56% of Cameroon's total export earnings. The 1982-87 5-year plan emphasized, hydrocarbon and agricultural development and targeted the exploitation of bauxite and clay deposits. New petroleum legislation was promulgated on November 26, 1982. Public Law No. 82-20 detailed hydrocarbon companies' obligations concerning oil and gas discoveries and exploitation. In general, the Cameroon Government has participated in joint ventures with private companies and has levied a 57.5% petroleum tax plus adjustable royalties. Exploration expenses were paid by concession holding companies, and the Government in the past has reimbursed 50% of expenses under certain conditions.

Jan 1, 1984