Search Documents

By Ronald S. Conti

This U.S. Bureau of Mines (USBM) report describes various fire-fighting resources available to the mining industry and examines the fire preparedness of four western coal mines. Information regarding fire-fighting equipment indicates that an inadequate maintenance program may cause component failure of fire extinguishers, damage to waterhoses is usually a result of improper care, and foam may be a convenient means of conveying water to the fire. Performance data relative to water nozzles (throw distance) and specific practices to improve the state of preparedness in many of these areas are discussed. Studies also indicated that a high-expansion foam plug, will travel down an entry, with a 1% rise in elevation, 207 m (680 ft) before a plywood stopping separating the generator and plug failed. The advance rate of the foam plug decreased when the entry is dry, requiring more foam concentrate and as the foam spread further down the entry. An examination of the mines showed state-of-the-art monitoring systems were common at the minesites. Fire safety was also stressed, including early detection and rapid response of the miners to evacuate the mine. However, the mines placed little emphasis on performance of water nozzles, or personal protective clothing for the underground firefighters.

Jan 1, 1994

By G. S. Scott

Mine fires have occurred since the mining of coal was begun, and they are still occurring. The resulting economic waste may become considerable (219),3 especially if a fire is allowed to assume major proportions or to get beyond control temporarily. It is important, therefore, to act promptly whenever a fire is suspected and to have every action count. To do this effectively, it is necessary to know at the earliest possible moment and thereafter what is happening in a remote or inaccessible area. It is equally important to know before¬hand what may be expected as a result of any proposed combative measure. The logical method of combatting a fire demands the cooperation of both mining engineer and chemist. They should decide the course of action to be taken, drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required for proposed operations, and the probable efficiency with which they could be carried out, and upon the chemist's knowledge of the results to be expected therefrom.

Jan 1, 1944

By BUREAU OF MINES

In July, 1918, the attention of the Secretary of the Interior WItS called to the rapidly increasing cost of producing gold and the declining output of that metal in the United States. Realizing the importance of the gold-mining industry, the Secretary appointed a. committee, consisting of Hennen .Iennings, chairman, J. H. Mackenzie, and Charles Janin, of the Bureau of Mines, and H. D. Me- Caskey and F. L. Ransome, of the United States Geological Survey, to,make a thorough study of the gold-mining situation in the United States. The study was to cover the increased cost of recovery and the decreased output of gold, and to consider the different measures that had been proposed to relieve the industry and stimulate production. This report embodies the results of the investigation and study made by the committee. The report presents statistical data compiled from various sources, showing the production of gold in the United States and other countries, with comparative figures for coal, iron, and other mineral products, and describes the sources and distribution of gold output in the United States. It discusses the relation of gold' production to finance and credit, the causes for the decline in gold output, and measures for the relief of the industry. The Interior Department publishes this report in the belief that the widest publicity possible should be given the findings of the committee in order that attention may be directed to the serious conditions revealed therein, and in the hope that wide discussion of the subject may result in some action being taken that will aid in upholding the gold standard ,and the gold industry.

Oct 30, 1919

By A. R. T. Denues

This investigation was made under a cooperative agreement between the United States Department of the Interior, Bureau of Mines, and the Pittsburgh Testing Laboratory. Funds were supplied by the Chile Exploration Co., whose executive offices are in New York City. The support, cooperation, and services of these agencies made the work possible and are acknowledged gratefully. The writer wishes to express his particular indebtedness to the staff of the Explosives Division of the Bureau of Mines for services and assistance, particularly Dr. Wilbert J. Huff, consulting explosives chemist, J. C. Holtz, J. E. Tiffany, and A. B. Coates; to F. O. Gardner, treasurer of the Pittsburgh Testing Laboratory; to G. B. Holderer, consulting engineer in connection with liquid-oxygen explosives for the Chile Exploration Co.; to the Enos Coal Mining Co. of Oakland City, Ind., particularly to G. H. Utterback of the staff of the mine for providing facilities that made field tests possible; and to full-time assistants J. W. Rothhaar and J. G. P. Weinheimer and to W. S. Hiller, part-time assistant, who were employed under the cooperative agreement.

Jan 1, 1940

By F. E. Diebold

The methodology for describing the geochemistry of elements in a coal seam have been developed. This has been applied to the Rosebud Coal Seam, which is an economically important member of the subbituminous coals of the Fort Union Formation in Eastern Montana. The method development has involved a detailed study of two popular techniques for determining the metal geochemistry of coal, namely, whole coal analyses and coal physical fractionation. The mathematically contrived element associations (whole coal analyses technique) and the element concentration trends in the float and sink fractions (physical fractionation technique) are considered to lead to only qualitative conclusions concerning the chemical associations of the elements in coals. Additionally, the processes taking place with the coal during low temperature ashing in an oxygen plasma are experimentally investigated and shown to be of sufficeint extent that the use of such low temperature ash for deciphering element geochemistry is questionable. The method developed in this study is a chemical fractionation that involves the sequential leaching of coal with water, 0.5 N HC1, 3 N HC1, 2 N HNO3, and 48% HF. These leach solutions are shown to selectively dissolve the predominate inorganic phases, sulfates, Ca and Mg carbonates, Fe sulfides and K alumino-silicates and quartz, respectively. These phases were identified with the use of XRD, SEM, EM and leaches (water and 0.3 N HC1) of whole coal and low temperature ash. The incorporation of the anion-exchange step in the leaching scheme was investigated and was observed to warrant further study of such intensity to be, at the time, unuseable. The use of this sequential leaching technique on several coal samples from the same seam generates element concentration trends that can be quantitatively interpreted with respect to the chemical associations of the minor and trace metals in the coal seam. The properties of the various seams of economic importance in the Fort Union Formation in Eastern Montana are compiled and presented. The subsequent conclusion is that there is not a large variation in the properties of these coal seams and that the variations within the Rosebud are within one order of magnitude. The chemical fractionation technique, investigated in this study, was applied to composite tipple samples of the Rosebud seam. Each composite sample represented 76,800 tons of coal. A minimum of 32% of the Ca and Mg are present as separate water soluble sulfates. An excess of the sulfate ion in the water extracts shows the predominating influence of the ion exchange capacity of the organic compounds in the coal. Based upon the CO content of the coal and the HC1 leachate data, 25 to 30% of the alkaline earth elements exist as separate carbonates and the remainder are associated with the organic compounds. The small fraction of the illite that dissolves in the HC1 and HNO3 leachates accounts for the K and Al. Slight dissolution of the pyrite in the HCl solvent occurs, the small amounts of Li and As do not relate to any known phase and Mn is present as a separate carbonate phase. Fe and a significant amount of the As exist in the pyrite that is dissolved in the HNO. Se is equally partitioned between the pyrite and the organic compound~. Most of the trace elements are found in the HF solutions. Li, V, and Cr were interpreted to be associated with the clay minerals (kaolinite and illite). Ni and Pb appear to be present as separate phases and 50% of the Hg is HF soluble but is not chemically related to any known inorganic phase.

Jan 1, 1983

By A. J. Forney

The hot-gas-recycle process, for the hydrogenation of carbon monoxide, was investigated in a 12-inch-diameter reactor. Initially because the distribution of gas was poor, hotspots developed in the catalyst bed. After the velocity profile of the gas flowing through the bed was studied, the method of packing the catalyst was altered. Because this change improved the distribution of gas, temperature control was excellent. The l2-inch-diameter reactor was operated successfully in the synthesis of gaseous and liquid fuels. When high-Btu gas was synthesized in two stages, parallel-plate assemblies of Raney nickel were almost as active as granular Raney nickel in the second reactor. The pressure drop through the second reactor, however, was reduced 90 percent by the use of these assemblies.

Jan 1, 1962

By Robert W. Geehan

A preliminary examination of the Dayton iron deposit was made in 1941 and 1942 by Paul E. Pesonen and O. H. Metzger, engineers of the Bureau of Nines. Trenching and sampling were recommended, to be followed by core drilling if favorable results were obtained. The Bureau of Mines conducted a project at the property from June to December 1942. The deposit is in sec. 6, T. 17 N., R. 23 E.; sec. 31, T. 18 N., R. 23 E.; sec. 36, T. 18 N., R. 22 E.; and sec. 1, T. 17 N., R. 22 E., M. D. B. & M., about 15 miles west of Lahontan Reservoir in Lyon and Storey Counties, Nev. It lies at an altitude of about 4,500 feet north of the Carson Plains, in the foothill section of mountains that rise to about 7,000 feet to the north of the property. The deposit may be reached by driving 12.5 miles northeast of Dayton over U. S. Highway 50, thence northerly 2.7 miles over a dirt road to the property. The climate is hot and dry in summer, with occasional thunderstorms some of cloudburst variety, and frequent high winds. Winters are usually moderate, with light snowfall and some subfreezing temperature.

Jan 1, 1949

By William N. Hale

This Bureau of Mines report gives a detailed study of water usage in the Montana mineral industries, along with projections for the future. The mineral industry of Montana in 1963 used 36.5 billion gallons of new water, and reused or recirculated an additional 53.5 billion gallons for a total water requirement or usage of 90 billion gallons. The petroleum industry was the major water user, followed by the copper and zinc industries. Many mineral industry operators provide their own water, and new water is withdrawn largely from surface sources. At present, sufficient water is available in rivers, streams, and reservoirs in Montana; however, shortages do exist locally near mineral industry operations using large quantities of water. Some is supplied from sources up to 44 miles distant. New water withdrawn by the State of Montana mineral industry is expected to increase from 36.5 billion gallons in 1963 to 51.1 billion gallons by the year 2000. The total-water requirement is expected to more than double, or reach 182 billion gallons by the year 2000.

Jan 1, 1966

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

By H. C. Fuller

A method was devised and developed by the Bureau of Mines for decomposing manganese sulfate at significantly lower temperature than that required by the conventional procedure of using heat alone. This technique, called the partial reduction method, effected decomposition at 700° to 800° C, as compared to 900° 1,000° C normally required. The process consisted of heating, in the absence of oxygen, a mixture of manganese sulfate and a controlled quantity of a reducing agent. The suitability of commercial-type equipment was tested in laboratory-size models of an externally heated rotary kiln, a r bbled muffle-hearth furnace, and a fluidized-bed reactor. The rabbled-hearth furnace gave the best results with the least operating difficulty produced a gas containing more than 80 percent SC and eliminated 96 percent of the sulfur when coal was used as the reductant. Sintering of the powdery decomposition product produced an agglomerate containing, in percent, 63.6 Mn and 0.4 S.

Jan 1, 1966

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By H. B. Hill

The discovery of the Oklahoma City field and its .rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of .Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38.5° A.P.I. gravity and several months later was completed at a depth of 6,624 feet. The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933

By A. A. Cochran

Methods of preparing small heats of steel containing radioisotopes were developed, and the techniques of stripping film autoradiography were used to detect and study the carbide and sulfide phases in titanium-bearing steels. Metallography had revealed areas of titanium sulfide and ferrite or pearlite adjacent to areas of titanium carbide and ferrite, and unidentified, irregular phases at the boundaries between these two areas. Sulfur 35 was used to deter-mine the extent of the titanium sulfide inclusions, and carbon 14 was used to delineate the titanium carbide phase. Individual radioactive areas were located with a resolution of approximately 10 microns. A general background exposure that was not correlated with microscopically visible phases was observed in the carbon 14 autoradiographs. The evidence from both sulfur 35 autoradiographs and carbon 14 autoradiographs indicated that the unidentified inclusions were sulfides rather than carbides. INTRODUCTION The use of radioisotopes to facilitate the work at the Rolla Metallurgy Research Center was expanded in fiscal year 1959 when the Bureau of Mines authorized the installation of an intermediate-level radioactivity laboratory. Before this time, sealed cobalt 60 sources had been employed for radiography, but no tracer work was done. The primary objective of the first experiments conducted in the new laboratory was to supplement physical metallurgy investigations of selected problems in steel research.

Jan 1, 1962

By Edward F. Redente

Several research projects have been conducted in the western United States to determine the optimum soil replacement thickness for reconstruction of rangeland and cropland. However, the information gained from these studies tends to be site-specific and not broadly applicable. Moreover, the possible interaction between soil thickness and mechanical and fertilizer manipulation of the overburden has not been adequately studied. To meet these information needs, research was initiated at Trapper Mine in northwestern Colorado in 1980 to study vegetation response to soil thicknesses of 15,30,45, and 60 cm and five manipulations that included disking, ripping, and fertilizing. All crops were harvested at peak standing crop and then weighed in the laboratory. Wheat grain yields were highest when soil thickness was 45 cm and the soil and overburden were ripped. Alfalfa yields appeared to be highest when overburden was disked and fertilized and soil was replaced to a thickness of 60 cm. For range vegetation, standing crop biomass was highest when overburden was ripped and soil was replaced to 60 cm thick. However, optimum performance was obtained from the maximum number of species and life forms by disking overburden and replacing 15 cm of soil. The performance of most range plant species has improved over the three years of the study. When the results of this study are compared to the results of other soil thickness studies, we can conclude that selection of management practices should be influenced by local climate, local soil and overburden conditions, type of crop or vegetation to be grown, and specific management goals for that crop or vegetation.

Jan 1, 1984

By K. K. Kelley

The collection and correlation of thermodynamic data concerning substances of metallurgical interest have constituted one of the major activities of the Pacific Experiment Station of the Bureau of Mines, at Berkeley, Calif., for the past several years. Earlier bulletins (32, 33, 34, 36, 36, 37, 38) s in this series are entitled: (1) Contributions to the Data on Theoretical Metallurgy. I. The Entropies of Inorganic Substances; (2) Contributions to the Data on Theoretical Metallurgy. II. High-Temperature Specific-Heat Equations for Inorganic Substances; (3) Contributions to the Data on Theoretical Metallurgy. III. The Free Energies of Vaporization and Vapor Pressures of In¬ organic Substances; (4) Contributions to the Data on Theoretical Metallurgy. IV. Metal Carbonates--Correlations and Applications of Thermodynamic Properties; (5) Contributions to the Data on Theoretical Metallurgy. V. Heats of Fusion of Inorganic Substances; (6) Contributions to the Data on Theoretical Metallurgy. VI. A Revision of the Entropies of Inorganic Substances-1935; and (7) Contributions to the Data on Theoretical Metallurgy. VII. The Thermodynamic Properties of Sulphur and its Inorganic Compounds. The present paper collects and discusses thermodynamic data relating to metal carbides and nitrides, with the view of obtaining usable heat and free energy of formation relationships. Pertinent data on both classes of substances are difficult to obtain experimentally and consequently are extremely rare; it is therefore necessary in many cases, if equations are to be derived, to introduce certain approximations and assumptions. Lack of adequate means of checking results by utilizing data of different types, such as was done frequently in the bulletins dealing with carbonates and sulphates, are readily apparent to anyone who has made even a cursory examination of the available information. Consequently, some of the relationships derived undoubtedly will be found to be inaccurate when more or better data become available. Nevertheless, in view of the importance of some of these substances, it appears worth while to consider the information available at present and to attempt the formulation of as complete a

Jan 1, 1937

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

By Michael J. Beus

This Bureau of Mines report describes field investigations conducted in the Coeur d'Alene mining district of Idaho to obtain data on rock stress and physical properties. The resulting information has been utilized as input to detailed finite-element analyses to establish structural design criteria for deep-vein mine shafts. Measurement techniques include the Council for Scientific and Industrial Research biaxial and triaxial strain cells, the U.S. Geological Survey solid-inclusion probe, and the Colorado School of Mines dilatometer. Physical property testing was conducted in the laboratory on core obtained from each test site. Limited in situ physical property tests were also conducted. Reason-able success was obtained with the CSIR equipment, which was considered the most suitable for stress measurement in the study area. Test sites ranged in depth from 1,200 to 7,700 feet and are described in detail. The stress data were reduced by least-squares linear regression techniques to enable prediction of vertical and horizontal stresses to 7,500 feet. Ratios between the horizontal stresses as utilized for shaft design varied considerably, and a hydrostatic condition is the exception, based on Bureau measurements. Physical properties also varied widely, due to the complex geologic structure. Analyses of the data in terms of the tectonic history of the area show reasonable correlation. Data from previous rock mechanics investigations from the Coeur d'Alene district were also compiled and presented as part of this report to justify any generalizations regarding stress conditions and physical properties of the district as a whole.

Jan 1, 1980

By D. G. Kuehn

Mass spectrographic studies have been conducted on the positive ions and neutral species of glow discharges containing 1.0 pct S02 and 1.0 pct CO in helium. Measurements were conducted for gas pressures from 3.5 to 10.1 torr using both dc and 60-Hz ac excitation. The ion species that were observed included S+, SO+, SO+, 0+, O2+, C+, CO+, and CO2+ with lesser amounts of SO3+, (CO)2+, SCO+, and (SO?CO)+ or CS+2. Interpretation of the functional dependence of the various ionic and neutral species on pressure and applied power showed that CO reacted with the SO formed in the discharges to produce CO2 and sulfur. Deposition of elemental sulfur was observed in the plasma container.

Jan 1, 1973

By William O. Vanderburg

This paper describing the mining practices at the Argonaut mine, Amador County, California, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described are those used in exploiting the low-grade gold ores in the heavy and swelling ground that occurs on the Mother Lode belt. The author acknowledges the assistance of E. A. Stent, vice-president, James L. Fontenrose, cost clerk, Joseph Mohorovich, mine foreman, of the Argonaut mine, and of E. D. Gardner, supervising engineer, United States Bureau of Mines, Southwest Experiment Station, Tucson, Ariz.

Jan 1, 1930