Search Documents

By John P. Coughlin

The Bureau of fines has tested a portable microseismic processor recorder at the Galena Mine, Wallace, ID, both in an environmentally controlled enclosure and, with minimal protection, in a working area of the mine. In both trials the device demonstrated effective and reliable data acquisition capabilities.

Jan 1, 1985

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

The Sago Mine Disaster, on January 2, 2006, placed renewed focus on several different aspects of safety in the underground coal mining industry. One area which received increased attention since Sago and other underground coal mining events is the concept of Safety Culture. This report describes the results of a pilot Safety Culture Assessment implemented at a small Appalachian underground coal mine, hereafter referred to as the Mine. The purposes of this pilot assessment were to (a) evaluate the feasibility and usefulness of a methodology for assessing safety culture that had previously been developed for use within other industries, (b) to initiate an investigation into the understanding and defining of the existing safety culture of the underground coal mining industry, and (c) provide meaningful and useful recommendations for the participating mine for their consideration in their ongoing quest to enhance their existing safety culture. This pilot assessment was conducted in July 2007. The report provides information regarding the presence or absence of safety culture characteristics within the Mine. Observations regarding the characteristics of the Mine?s safety culture that should be sustained are presented. Areas in need of attention and management focus to improve the Mine?s safety culture are presented as well as recommendations for moving forward. Safety culture characteristics that are important for the existence of a positive safety culture have been identified to include: - Safety is a clearly recognized value in the organization. - Accountability for safety in the organization is clear. - Safety is integrated into all activities in the organization. - A safety leadership process exists in the organization. - Safety culture is learning driven in the organization. - A process for establishing a strong and effective Safety Conscious Work Environment (SCWE) is in place. Performance objectives are associated with each of the safety culture characteristics and particular behaviors and attitudes have been identified that can be measured to evaluate these objectives. Using a methodology originally developed with the support of the U.S. Nuclear Regulatory Commission, an assessment of selected organizational behaviors and attitudes was conducted to evaluate the Mine in terms of these safety culture characteristics and their associated performance objectives. The methodology involves obtaining a variety of quantitative and qualitative information, using multiple data-gathering methods. The information collected is largely based upon the perceptions of the individuals in the organization. The evaluation is a ?point in time? snapshot of the Mine, but cultural beliefs and assumptions do not change quickly. The feasibility and usefulness of the methodology was successfully demonstrated during this pilot assessment. All aspects of the methodology including functional analysis, structured interviews with accompanying behavioral scales, work observations, and the paper and pencil

Aug 1, 2007

By Charles A. Steen

Publication of this information circular results from an invitation extended to the Bureau of Mines by the Utex Exploration Co. to visit the company mine, on the Mi Vida claim about 39 miles southeast of Moab, in the Big Indian mining district, San Juan County, Utah. The Bureau is pleased to present this record of the Utex mine -- a property that in the relatively short period of 4 months has become one of the major uranium-ore producers on the Colorado Plateau. The ore deposit was discovered in July 1952 by Charles A. Steen, a geologist-prospector, now chief geologist of the Utex Exploration Co., in tae course of drilling the first diamond-core borehole in the Big Indian district. High-grade ore, 14 feet thick, was penetrated by the borehole. Sinking of a shaft, from which to develop the ore body, was begun in October, and the first shipment of ore left the property December 6, 1952. Ore production, as recorded on ore-settlement sheets received by the company up to July 15, 1953, totaled 16,000 tons averaging, 0.51 percent U305 and 1.25 percent V205. Discovery of the ore body and the large production of ore were achieved without any financial assistance from the Government.

Jan 1, 1953

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By H. L. Gilbert

Zircon sand may be reacted with sodium hydroxide at 600° C. to form sodium zirconate and sodium silicate. Sodium zirconate is water insoluble and so may be washed free of sodium silicate. The sodium zirconate may then be converted to zirconyl chloride by the action of hydrochloric acid and the zirconyl chloride crystals separated by cooling the solution. This approach produces zirconyl chloride of satisfactory purity with less cost than is involved in buying anhydrous zirconium chloride and converting it. A proposed design for a plant is given, INTRODUCTION This work was conducted by the Rare Metals Branch as a part of research on zirconium at the Bureau of Mines Northwest Electrodevelopment Laboratories, Albany, Oreg., under the guidance of S. M. Shelton, Regional Director. The work was supervised by W. W. Stephens, head of the Rare Metals Branch (now with Carborundum Metals Corp.).

Jan 1, 1954

By R. K. Guthrie, H. B. Hill

"INTRODUCTION The Rodessa oil field in Marion and Cass Counties, Tex., Miller County, Ark., and Caddo Parish, La., was discovered in August 1930, when a well drilled to a depth of 5,506 feet in Caddo Parish, close to the surface trace of the Rodessa fault, produced gas in commercial quantities. During the next 5 years 21 gas wells were drilled, and a large reserve of natural gas was developed in the high part of the Rodessa structure underlying the Massive Anhydrite member of the Glen Rose formation.In July 1935 oil was discovered on the flank of the structure when a well drilled to 6,048 feet also in Caddo Parish, was completed as an oil well. The discovery of oil in the Rodessa structure initiated art intensive development program of more than usual interest to geologists, engineers, and operators in the petroleum and natural-gas industry. The complex nature of the different reservoirs, the large volume of ""free"" gas under high pressures and temperatures in the upper part of the reservoirs, and the high gas:oil ratios of some of the wells during the early production of oil presented many problems the solution of which taxed the ingenuity of those responsible for the development and exploitation of the Rodessa field.Early waste of gas and resultant dissipation of reservoir energy led to State intervention, which brought about effective regulation of the quantity of gas blown to the air. Oil production from wells producing more than 2.000 cubic feet of gas per barrel of oil was restricted, and oil allowables generally were based equally upon acreage and upon reservoir pressures. Consequently, oil-production statistics of the field are closely associated with gas:oil ratios and reservoir pressures.The primary object of this report is to present factual and statistical data on well performance in the Rodessa field and to show established trends under certain operating methods and practices in high-pressure gaseous reservoirs, which have been carefully developed and outlined by modern technique and exploited under close engineering supervision.The large size of the Rodessa field, it’s fairly well defined gas caps, and a somewhat definite water table in a part- of the oil- and gas-producing region are of special interest and importance in a study of the fluid and energy relationships in reservoirs. Consequently, the results of much of the authors' work in collecting and compiling date are presented in the form of tables, maps and cross sections to show the relative thicknesses of the different oil-and gas-producing members and their permeability and porosity relationships, and, when possible, the variations in stratigraphy are exhibited in cross sections. Results of a detailed analysis of cores from a number of wells also are presented in tabular and graphic form."

Aug 1, 1943

By Forrest T. Moyer, J. I. DAVIS, JOSEPH H. SCHUSTER, E. K. ELSNER

The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior, is held each year for the purpose of promoting safety in the mineral industries of the United States. Since the program was inaugurated in 1925, twenty-three safety competitions have been held. This publication is a report of the results of the contests held in 1944, 1945, 1946, and 1947. The names of plants that have been awarded "Sentinels of Safety" trophies and Certificates of Achievement in Safety dur- ing these years, together with a summary of their achievements in injury prevention, are listed. Statistical data covering the injury experience of all plants entered in the annual contests also are included in this publi- cation. The injury statistics of these plants, arranged in the six groups of the competition, are the only data on injury severity at mineral operations available to the Bureau of Mines. Interest in the National Safety Competition has increased steadily. The number of participating plants has increased from 210 in 1925, the first year of the competition, to the record number of 494 in 1946. The widening scope of the competition means that a steadily increasing number of the mines and quarries in the United States are participating in a program that will supplement their other activities in promoting safety. Safety competitions have long been recognized as instrumental in stimulating and holding the interest of employees and officials in accident-prevention work. During the years covered by this report, conditions in the mineral industries of the United States were hardly conducive to setting records in accident prevention. During the war years, handicaps were especially severe- loss of skilled employees to the armed forces or to higher-wage war industries, greater production by a smaller force of workers, relatively high rates of labor turn-over, the longer workday in effect through 1944 and 1945, and difficulties in obtaining repairs and replacement for badly worn machinery. Even the immediate postwar period has brought no abatement of the tremendous pressure upon the mineral industries for greater production. Although there was a decrease of 18 in 1947 from the record enrollment in 1946, these oper- ations worked 160,525,025 man-hours, the greatest number of man-hours of exposure to mining hazards in any year of the contest except 1942. Despite the accelerated pace at which the mineral industry worked during the 4 years covered by this report, participants in the National Safety Competition have achieved creditable performances in the promotion of safety. In fact, the injury-severity rate in the enrolled plants in the 1947 contest was 7.315 days for each thousand man-hours worked, the lowest by far in the history of the National Safety Competition. The injury-frequency rate of 42.155 for each million man-hours of exposure to mine hazards in 1947 marks a favorable trend downward from the rate of 50.577 in 1946, which was the

Dec 1, 1949

By Parry. V. F., John B. Goodman

"INTRODUCTION The Denver region coal field, covering an area of approximately 7,640 square miles, extends from the Wyoming State line to the middle of El Paso County, Colo. The coal in this region is subbituminous in rank. Much of it is used as domestic fuel. During the last decade the production of coal in this field has remained fairly constant at an average of 2,600,000 tons per year. This production has come from 50 to 60 mines, 88 to 90 percent of the production being from the section of the field north of Denver.According to the Standard Specifications for Classification of Coal by Bank of the American Society for Testing Materials 4/ the coals in this region are classified in the Subbituminous B and C group. On the as—mined basis, they contain about 22 percent moisture and average 9,600 B.t.u. per pound. They are noncoking and slack to a variable extent when exposed to the weather. This is characteristic of subbituminous coals."

Aug 1, 1939

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By Sarkis G. Ampian

Published optical microscopic and X- ray diffraction characteristics of the following compounds are critically evaluated and compared with Bureau of Mines data : Tricalcium aluminate , calcium monoa luminate , dodecacalcium heptaluminate , dicalcium silicate , tricalcium silicate , and sodium aluminate . A recommended set of definitive optical and X- ray diffraction characteristics is presented . These values are used to identify products of the lime soda sinter process for production of alumina . Polymorphism of gamma- , beta- , and alpha prime - dicalcium silicate is reexamined , and new data are presented on polymorphism of tricalcium silicate and sodium aluminate by high- temperature X- ray diffractometry . Polymorphism is not observed for tricalcium aluminate , calcium monoaluminate , and dodecacalcium heptaluminate . Bureau of Mines data indicating a stoichiometry of 12Ca0.7A10 for the phase 5Ca0.3A1 0₂ are discussed . A critical review of the literature concerning calcium dia luminate and sodium undecaluminate ( 8 -A10 ) is also included .

Jan 1, 1964

By Charles L. Harness

The barite industry has made notable progress since the days when barite was used only as an adulterant in white-lead paints and the only method of mining it was with pick and shovel. The following chronological record may serve to show how this heavy white mineral has grown in importance in the national exonomy and at the same time to indicate development of methods for obtaining it. 1845. - Barite first, mined in Fauquier County, Va., for use as an adulterant in white-lead paints. 1850 (approx.). - French settlers 60 miles southwest of St Louis, Mo., discovered barite; called it "'tiff;' meaning white. It was mined and shipped to St. Louis for use in paint.

Jan 1, 1946

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By ARCH L. FOSTER

The rapid increase in the mmber of automobiles during the last 25 years has resulted in the insistent and growing demand for better roads of more permanent construction. Some form of State license for the operation of automobiles has been in effect almost from the time of the first "self-propelled" vehicle, and some part of the revenue derived from the sale of these licenses has been applied to the maintenance and construction of roads. However, to obtain funds with which to build their present highway systems, the individual States have resorted to the taxation of gasoline. The first State to adopt a gasoline tax was Oregon, the law becoming effective February 25, 1919. By 1928, all of the States except two had levied taxes on gasoline at rates varying from 2 to 5 cents per gallon. New York and Massachusetts passed gasoline tax laws which became effective in 1929. Regulations governing the quality and the methods of handling gasoline and other petroleum products sold in the States have also been adopted by 29 States; many of these laws antedate the adoption of a gasoline tax. The variations in motor fuel speci- fications and methods of test have been pronounced in the several States. The Bureau of Mines, in making certain technical studies of the rasolines marketed throughout the United States, the results of which are reported in its semiannual motor gasoline surveys and other reports, has had occasion to obtain and compile all of the present (April 1, 1931) tax and pection laws of the several States which relate to motor fuel and other petroleum products. To facilitate the use of this material and to obviate the need in most cases of reading the complete text of the laws as published by the States, the pertinent information was arranged in tabular form for cly reference. 3 Although digests of States gasoline tax laws' are available and copies of the complete laws can be obtained from the State agancies in charge of the enforcement of gasoline tax and inspection laws, it is believed that

Jan 1, 1932

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By P. L. Woolf

Seven evaluation tests with blast furnace iron bearing burden materials are described. The effects of pellet strength, fines in the burden, decreasing slag volume, pellet size, eliminating stone with superfluxed sinter, and eliminating stone by prefluxing the pellets were determined. Fluxed pellets and fluxed sinter made with the same ore fines were compared. The tests were conducted under cooperative agreements between the Bureau of Mines and North American steel companies. The objectives were to improve blast furnace practice, expand and develop understanding of the operation and theory, quantify the effects of changes, and explore the limitations of operability. This work was part of an extensive program of blast furnace research in experimental blast furnaces at Bruceton, PA conducted in the years 1958 to 1967.

Jan 1, 1984

By David R. Jessey

This volume contains the detailed mine site reports written by the WAPORA, Inc. and KETRON, Inc. staffs. It is a companion Appendix Volume to Control of Water Pollution from Surface Mining Operations. Copies of this report are maintained on Open File at the U.S. Bureau of Mines Research Center, Spokane, Washington.

Jan 1, 1981

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood-block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 2010

By L. E. Dalverny

This Bureau of Mines report describes the deployment, 5-month operation, and lessons gained from a continuous gas monitoring system using sampling-tube bundles at an underground mine fire in West Virginia. Research information gained indicates the utility of relating certain gas concentration ratios to events during fire development, mine reventilation, and mine recovery. In addition to monitoring the quality of remote fly ash seals, the system provided timely warning of dangerous gas concentrations which developed during surface and underground recovery activities. An evaluation of system components is supplemented by recommendations for improvements.

Jan 1, 1975