Search Documents

By Martin A. Elliott

The Bureau of Mines began its investigation of the use of Diesel engines underground to provide technical information necessary to assist this development in the United States. It was considered desirable to furnish such assistance because successful European developments/ in this. field had indicated that Diesel mine locomotives might be safer than electric trolley locomotives. The Bureau has recognized for some time the importance of eliminating the hazards associated with underground haulage systems using bare trolley wires. For example, each year 30 to 40 fatalities occur as a result of electrocution by contact with bare trolley wires. In 1943 and 1944, 101 men were killed and extensive property damage occurred as a result of mine fires started by falls of roof grounding the bare trolley wires.

Jan 1, 1948

By P. C. Good

The work reported here was undertaken by the Federal Bureau of Mines to investigate new methods of preparing high-purity metal. Tungsten hexachloride was prepared by direct chlorination of scrap tungsten metal and by treating tungstic oxide with carbon and chlorine. The resulting tungsten hexachloride was purified by distillation and reduced win: sodium, magnesium, or hydrogen. The metal prepared by these techniques was at very high purity after arc melting but of variable quality prior to arc meIting. Metal recovery ranged from about 40 to 90 percent of theoretical values, It was found possible to deposit a smooth, dense coating of high-purity tungsten on the inside of a heated tube by vapor-phase reduction of tungsten hexachloride at reduced pressure.

Jan 1, 1961

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966

By L. E. Schultze

Experiments were conducted by the U.S. Bureau of Mines to verify enhancements due to chloride and surfactant additions in the leaching system of chalcopyrite with ferric sulfate and sulfuric acid. A statistical experimental design was used and equipment was designed to eliminate contributions from changes in solution electrochemical potential during the course of the measurements. Results confirmed that chloride additions increased chalcopyrite leaching by as much as 94 pct over the electrochemical potential versus hydrogen electrode range of 630 to 750 mV at pH 1.7 and 50°C. Total iron concentration had no effect over the range of 1 to 5 g/L. The effect of surfactant addition was less well defined. While additions of LA 790 (a polyoxyethylene lauryl ether) resulted in increased copper leaching in several of the tests, the differences were too small to be statistically significant. No interaction effect could be verified.

Jan 1, 2010

By G. L. Oldright

This paper is the second of a series that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. The writers wish to express their appreciation to the management of the International Smelting Company at Tooele. Utah, for their kind cooperation which made possible the assembling of these data.

Jan 1, 1929

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

By M. J. Ankeny

All bituminous-coal mines, by the nature of their product and inherent gassy tendencies, are subject to explosions or mine fires. The evolution from large, hand-loading sections employing numerous men and containing open-type equipment, lights, and nonpermissible explosives to small, concentrated mechanical sections with but few well-supervised men utilizing modern preventive equipment has not altered this premise. Mine catastrophes such as Centralia and New Orient No. 2, as well as recent disasters of less magnitude, have refuted the trend of thinking that modern equipment, will prevent or localize explosions and prevent widespread or loss of life.

Jan 1, 1952

By F. A. Skirvin

Purification techniques were investigated for removing low-level metallic impurities from tungsten hexachloride. These techniques included distillation) fused-salt scrubbing) zone refining) and adsorption. Fractional distillation of tungsten hexachloride was found to be an effective purification method. The impurity levels of molybdenum) iron) nickel) copper) magnesium) and manganese were reduced to provide a tungsten halide sample which contained a total of less than 10 ppm detectable metallic impurities. Purification by fused-salt scrubbing of tungsten hexachloride in a lithium chloride-potassium chloride eutectic produced a hexachloride product which was of approximately the same quality as that obtained by distillation. Zone refining and adsorption did not appear to be as effective as distillation or fused-salt scrubbing.

Jan 1, 1967

By William C. McBee

Specialized sulfur concretes were developed by the Federal Bureau of Mines as a result of research for the beneficial utilization of sulfur in construction materials. Materials were developed for use in acid and salt corrosive environments where portland cement concrete has been found to deteriorate. Because the mineral aggregates also come into contact with the corrosive media, concretes were developed utilizing both limestone and quartz aggregates. The sulfur binder used with both aggregates was modified by reaction with 5 pct dicyclopentadiene to improve product durability. Sulfur quartz aggregate concrete was found to have moderately high strength characteristics (6,000 psi compressive) and was extremely resistant to chemical attack by both acid and salt solutions. Sulfur limestone aggregate concrete exhibited very high strength characteristics (9,000 psi compressive) and was extremely resistant to chemical attack of salt solutions. Both types of concretes maintained their strength and integrity after long-term testing in acid and salt solutions and exhibited considerable resistance to damage by the action of freezing and thawing. Potential uses include leach tanks, electrolytic cells, thickeners, bridge decking, industrial flooring, pipe, and tile.

Jan 1, 1979

By R. R. Lowery

The Bureau of Mines developed hypereutectic aluminum-silicon alloys which 11.7.d better mechanical properties than the unmodified hypereutectic alloy. A commercial aluminum-20 weight-percent silicon LIr alloy was selected as a ary base for improvement. The primary silicon. grains were reduced from ASTM 4-5 to ASTM 8.5 by the use of phosphorus and phosphorus compounds. The remaining eutectic matrix was refined by sodium metal additions of 0.2 weight-percent. Solid solution strengthening of the alpha aluminum was obtained by adding 2 percent copper and 0.5 percent magnesium. Also, 1 percent nickel was added to harden the alloy. Optimum thermal treatment consisted of a solution treatment for 10 hour:, at 480° C with hot water quench, followed by aging for 6 hours at 175° C. The final alloy exhibited a Rockwell B hardness of 75 ±2 in the heat-treated condition. The ultimate tensile strength was 39,5O0 psi with no recordable elongation. The coefficient of linear thermal expansion was 20.4 x 10-6 per °C in the temperature range 20° to 300° C. No wear resistance data were collected.

Jan 1, 1966

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963

By F. A. Rutledge

"The chromite deposits of Red Mountain, 10,miles southeast of Seldovia, Alaska, are in an intrusive of ultramafic rocks. The earliest reference to the deposits was made by U.S. Grant3/; J.B. Mertic, Jr. 4/ made a brief examination in 1917; and A.C. Gill5/ spent 7 weeks studying the ore bodies and geology of the region in 1918. The Federal Geological Survey had a field party in the region from July until September 1940 and the Red Mountain area was mapped and geological data were assembled by P.W. Guild.6/A preliminary investigation of the Kenai chromite deposits was made in July 1941 by R. S. Sanford,7/district engineer of the Bureau of Mines, accompanied by P. W. Guild, assistant geologist of the Geologi¬cal Survey. This was followed by surface sampling and core drilling, which were completed in September 1942 under the direction of John W. Cole,8 associate engineer of the Bureau of Mines. G. O. Gates, associate geologist, and A, B. Unkelsbay, junior geologist, of the Geological Survey, logged cores and interpreted geologic features revealed by Bureau of Mines drilling and trenching.9/J. C. Roehm, associate engineer of the Territorial Department of Mines; examined the Red Mountain area in august 1941.10/Additional exploration of other deposits in. the Red Mountain area was completed during the summer of 194. Work consisted of surface sampling, core drilling, and mapping. G. O. Gates, associate geologist of the Geological Survey, spent 4 days in August investigating results of the Bureau of Mines program.Throughout the exploratory work conducted by the Bureau of Mines the cooperation of Red Mountain Chromite, Inc., and especially of John Blodgett, Jr., and Collis 2, Druley, president and superintendent, respectively, was greatly appreciated. Use of their camp in the Windy River cirque and shops at Kasitsna Bay facilitated the Bureau of Mines program."

Apr 1, 1946

By K. D. Plants, J. H. Holden, L. F. Willmott

Pulverized high- volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure - gasification pilot plant equipped for steampickup feeding . The pilot plant operated satisfactorily at relatively high steam- to - coal ratios , but steam- to - coal ratios could not be reduced much below 0.5 lb / lb without condensation of steam or softening of the coal . Carbon gasified , gas composition , and coal and oxygen requirements were essentially the same as for a pilot plant equipped with a fluidized coal feeder . Average results from the pilot plant equipped for steam- pickup feeding were coal requirement , 37.3 lb/M ( 1,000 ) scf of CO + H₂ produced ; oxygen requirement , 358 scf /M scf CO + H₂ produced ; and carbon gasified , 87.7 percent .

Jan 1, 1964

By W. W. Adams

The safety record established by the coal-mining industry of the United States during 1934, although not as favorable as that for the previous year, was better than the record for any other year during the period 1930-34 for which complete figures covering fatal and nonfatal accidents at the mines are available. The number of accidents was 89.98 per million man-hours of employment compared with 86.74 for the year 1933, the latter being the lowest rate in any of the 5 years referred to. The rate was 105.60 for 1930, the first year covered by available data. Employment increased in 1934; the number of workers represented an increase of 8 percent over the year 1933, man-shifts of labor increased 16 percent, and the number of man-hours of labor increased 7 percent. The total number of man-hours of employment also exceeded the number reported for 1932, and was almost equal to the record for 1931.

Jan 1, 1936

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By John C. Edwards

The Bureau of Mines has developed a time-dependent mathematical model of radiative heating of bulkheads in mines. The model includes both reradiation from the duct (cylindrical) walls and direct radiation from the fire zone. Thermal loss into the wall of the duct and into the bulkhead is included. Both brick and wood bulkheads are considered. It is found that the heating rate of the system scales as the duct length-to-diameter ratio and the flame temperature. In particular, the time required for the irradiated surface of the bulkhead to reach a specified temperature decreases with increasing flame temperature for a fixed length-to-diameter ratio and increases with increasing length-to-diameter ratio for a specified flame temperature. It is also deter-mined that the time, T, for the bulkhead surface temperature to reach a specific value, Tb, for a fixed length-to-diameter ratio less than 4 and for a flame temperature of 1,200 K is approximately linearly dependent on Tb for 500 K < Tb < 700 K, and is nearly exponentially dependent on the length-to-diameter ratio for Tb = 600 and 700 K.

Jan 1, 1979

By Joseph Grumer

Reported fiscal year 1973 studies of fires and explosions seek to develop capabilities during mining operations to detect and quench ignitions of gas in the face area, to detect and quench by means of passive or triggered barriers explosions propagating in rock-dusted coal dust, and to detect incipient fires early enough for easy extinguishment. Research discussed includes minimum air velocities to lift coal or rock dusts, surveys to determine adequacy of rock dusting, chemical agents to quench gas or coal dust explosions and their relative efficacies, spectra radiated by explosions, and nozzle sprays of extinguishants.

Jan 1, 1973

By Chase E. Sutton

The porosity of a sand is usually the measure of its capacity for holding fluid, although porosity is sometimes selective; that is, a small percentage of the actual pore space (voids), particularly in fine-grained sandstones, may be isolated by the cementing material which prevents the entrance of fluids under normal conditions. Obviously, however, porosity determinations are essential to an engineering study of underground conditions of an oil field, and a simple and reliable method of obtaining a reasonably accurate figure for average porosity is desirable. This report describes a method suggested by Ruasell,3 which was used by the writer in the preparation of a report on the Texhoma-Gose pool, Archer County, Tex.4 The conditions in this pool were particularly favorable for obtaining an average porosity figure, in that some 30 to 35 core samples of the pay sand were available for analysis.

Jan 1, 1928

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981