Search Documents

By P. A. Wasson, M. M. Fine

Roasting research involving small , batch experiments was conducted to explore the use of solid reductants for converting nonmagnetic iron ore to a magnetic type . Three typical Minnesota ores were tested with one or more of the following reductants : Lignite , lignite chars , anthracite , bituminous coal , petroleum coke , peat , and pyrite . Reductive roasting was accomplished in a 3- by 4- inch externally heated rotating drum . Ore and reductant were placed in the drum and heated to a desired temperature , which was maintained for a predetermined period . Recoveries of over 90 percent of the iron in magnetic concentrates were achieved at 650 ° C , using lignite , some lignite chars , a high- volatile bituminous coal , peat , and pyrite . Pyrite is a novel reductant , which is superior to carbonaceous materials other than lignite and some chars .

Jan 1, 1963

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By Scott Turner

The monetary metals , gold and silver , have recently been the object of such general interest that the United States Bureau of Mines has received many inquiries regarding them . Though requests for technologic information have been numerous , they have been exceeded in number by those concerned with economic aspects of these metals . The nature of the latter communications indicates that the public is not generally aware that various Bureau publications are available which deal with the economic situation of gold and silver . For this reason , it is deemed advisable to present a brief résumé of the papers which are obtainable from the Bureau or the Superintendent of Documents , together with the text of three articles recently prepared by the Director , reprints of which are not otherwise available . The Bureau of Mines compiles figures showing mine production of gold and silver , by districts and States , and cooperates with the Bureau of the Mint in determining the total annual output in the United States as a whole . 3 It recently established an annual canvass to determine the consumption of silver in the arts and industries of the United States , and published an economic paper covering such use in 1928 and 1929 , followed by an information circular on silver consumption by industry during the 2 years subsequent . A 4-year record is thus provided for those interested in utilization of silver . The Bureau has also published summarizations of all available data upon world production since 1493 of gold and of silver . It has , furthermore , rendered available a compilation of production- data of silver mines of the world , and an analysis of it , showing the proportions of silver and other metals contained in all the ores from which silver is derived . " All of these papers are concerned solely with putting into readily usable form statistical data and other factual material ; they do not offer theories or express opinions upon controversial questions related to these metals . Three other recent papers concerned with gold and silver are presented below in order to put them in shape for distribution by the United States Bureau of Mines . All three of them are by the Director of the Bureau . It should be noted that these papers do not commit

Jul 1, 1933

By T. A. Henrie, J. D. Marchant, E. S. Shedd

Cerium metal was electrowon in a fluoride bath from cerous oxide and tapped from the cell during prolonged operation . Electrolyte constituents were CeF , BaF₂ , and LiF. Twenty- seven pounds of metal of 99.8 percent purity were produced at a rate of 3 pounds per hour and tapped from the cell . Principal impurities were molybdenum , aluminum , oxygen , and carbon . The operating parameters , such as electrode geometry , bath compositions , and oxide feed rate , were investigated . Anode reactions were found to be important factors in cell operation . Stable cerous oxide reacted more uniformly at the anode surface than ceric oxide . Electrowinning was conducted in crucible hearths consisting of both frozen electrolyte and molybdenum metal . Both materials proved satisfactory and did not react with the molten cerium . Stable cerous oxide was prepared by carbothermic reduction and used as a feed material . Cell design proved to be an important factor in continuous cell operation . Complementary to the investigations of electrowinning of cerium , the metal was purified by electrorefining in a chloride electrolyte .

Jan 1, 1964

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954

By C. J. Chindgren

A refractory-lined, garage-type automobile incinerator with a natural gas afterburner for air pollution control was cooperatively constructed and tested by the Bureau of Mines and the Wasatch Metal & Salvage Co. in Salt Lake City, Utah. The incinerator is capable of relatively smokeless burning of 32 to 60 cars per day, dependent on the degree to which the cars are stripped prior to incineration. Preliminary burning campaigns indicate the cost of incineration to be approximately $2.75 per car.

Jan 1, 1970

By Carl L. Bieniewski

U.S. molybdenum production increased fivefold from 18.2 million pounds in 1946 to 90.5 million pounds in 1966, and constituted 87.3 percent of the total free world supply in the 1946-66 period. Mining development in other free world countries in the next few years may reduce the magnitude of the U.S. position, although similar development planned for the United States may counteract some of the relative gains by those countries. In 1966 two-thirds of the reported molybdenum consumption in the United States by end uses was as an alloying element in steel. Molybdenum also has important use as an alloying element in iron and high-temperature alloys. Consumption of molybdenum metal for making fabricated parts has increased in the past few years, especially in the space and nuclear industries. Molybdenum compounds are used mainly for making pigment, catalysts, and lubricants. Based on producer reports of shipments of primary products to domestic customers, U.S. consumption of molybdenum increased from 16.5 million pounds of molybdenum in 1946 to 65.6 million pounds in 1966. U.S. molybdenum reserves are now estimated to be 5.9 billion pounds of recoverable molybdenum, an increase of 2.1 billion pounds above previous estimates. Molybdenum ores account for 71.4 percent of the reserves, copper ores for 22.3 percent and copper-molybdenum, tungsten, and uranium ores for 6.3 percent. Several methods for predicting future demand are illustrated and estimates of demand using these methods were made for 1975. Based on present capacities and announced company plans for future developments, estimates of annual production were made for 1967 through 1975 for the United States, Canada. Chile, Peru, and the free world. These data indicate that molybdenum production in 1975 for the free world is expected to be 246 million pounds with the United States producing 68.2 percent and Canada, Chile, and Peru 30.3 percent.

Jan 1, 1970

By Robert H. Essenhigh

A stirred reactor (SR) combustion system has been developed to gather information on the mechanisms of ignition and flame propagation of coal dust under conditions similar to those found in coal dust explosion flames. The prime scaling variable considered in this study is that of rapid particle heating (between 105 and 106°K/sec) which is accomplished by means of turbulent mixing during combustion. The SR combustors tested in this study have consisted basically of spheres hollowed in the centers of refractory housings. Coal and air mixtures have been injected into the spherical combustion chambers through a single jet, two opposed jets or four opposed jets. The diameters of the jets have ranged from 0.63 to 0.22 cm. The volumes of the combustion chambers have ranged from 1.0 to 0.2 liters. The reactors have been equipped with thermocouples embedded in the combustion chamber wall as well as a thermocouple located in the exhaust gas stream. In the latter versions of the SR, provisions were made for both solid sampling and gas sampling of the reactant stream exiting from the combustion chamber. Experiments have been carried out using pulverized bituminous coal. The coal has been reacted in an SR in mixtures of air and air/nitrogen. These experiments have provided information on the mode of ignition of the coal as well as yielding information on the kinetics of coal pyrolysis through the use of SR theory. Ash tests performed on the reacted samples collected from the SR indicated that the majority of the values of weight loss percentage were between 60 and 70 percent. The percentages of weight loss were relatively unaffected by changes in temperature which varied between 1100 and 1700°K and by changes in residence time which varied between 10 and 20 millisec. Volatile matter tests performed on the samples indicated that the volatile matter left in the char ranged from 3 to 20 percent of the original content. By assuming that all the mass loss was due solely to pyrolysis with no combustion occurring at the particle surface, Q-factors for each test have been calculated. The results of these calculations indicate an average value of Q equal to 1.88. This finding shows that the majority of mass loss can be attributed to pyrolysis. The fact that the extent of reaction varies only slightly over the range of test conditions has been examined in the context of the two component hypothesis of coal constitution. This approach leads to the conclusion that the reaction of the "easily evolved" component VMI is extremely rapid and that the majority of it is removed from the coal in times less than the residence time in the system. This means that the volatile residue remaining in the char can be considered to consist of component II, VMII. If the mass fraction of VMI = 0, then an activation energy of 18.0 kcal is obtained for the pyrolysis reaction. If the mass fraction is assumed to be 0.75, the activation energy increases to 31.2 kcal.

Jan 1, 1978

By J. Sammarco

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to determine if light-emitting diode (LED) cap lamps can improve safety by reducing glare. Glare can impede a miner?s ability to see hazards and to safely perform their work. Another objective is to determine if a person?s age is a factor. This is important because the workforce is aging ? the average miner is now about 43 years old. Three cap lamps were used to evaluate glare: an incandescent cap lamp, a commercially available LED cap lamp and a NIOSH prototype LED cap lamp. Thirty NIOSH personnel from the Pittsburgh Research Laboratory (PRL) served as test subjects. Three age groups were established with ten subjects in each group. Testing was conducted in the Mine Illumination Laboratory (MIL) of NIOSH PRL. The results indicate no statistically significant difference in discomfort glare among the incandescent and LED cap lamps. However, an analysis of variance for disability glare indicates that the LED cap lamps were superior for the older subjects. Disability glare scores for the oldest subject group improved 53.8% when using the NIOSH prototype LED cap lamp compared to the incandescent cap lamp and 36.5% compared to the commercial LED cap lamp. It ap­pears that, given the conditions of this study, LED cap lamps will not increase discomfort glare and can enable significant improvements in disability glare for older workers. It is also evident that not all LEDs are created equal. The disability glare improved the best for older workers when they used the NIOSH prototype LED cap lamp, which has a different spectral power distribution (SPD) (more short wavelength energy) than the commercial LED cap lamp. Therefore, for disability glare, the results suggest that the SPD is an important factor to consider in cap lamp design.

Jan 1, 2009

By G. R. Palmer

The Bureau of mines evaluated the elution of uranyl carbonate from a strong base resin with a mixed carbonate eluant in a fluidized system. The system consisted of a multiple-compartment ion-exchange (MCIX) elution column with a continuous flow of solution, except for short periods when the resin increments were withdrawn. The exchange of uranyl carbonate from the mill-loaded strong base resin with an eluant composed of 1.0 [M] NaaCOs plus 1.0 [M] NH4HCO3 was studied. The effects of solution flow rate, aqueous-to-resin flow ratio, column diameter, compartment height, initial resin concentration, and column length were examined. The experimental data indicate that for the eluant examined, a resin residence time of 240 minutes is necessary to attain 90-percent elution efficiency. Also provided is a technique for sizing an elution MCIX column form pilot plant experimental data.

Jan 1, 1979

By John B. Gayle

The coking time has considerable influence on the throughput of a coke oven, and for this reason a large number of papers dealing with the relationship between coking time and the different operating variables have been published. Although all factors known to influence the coking time have been studied, agreement has not been reached on several questions.2/3 Therefore, it appears worthwhile to evaluate any data that become available during investigations of the carbonizing properties of various coals and coal blends. Because it is expected that reports covering several different phases of this problem will be forthcoming as additional data-become available, the following study of the relationship between coking time and bulk density represents a report of progress on the overall investigation of factors influencing the coking time in slot-type ovens. The practice of including coarse coal in the blend going to the ovens to obtain increased bulk densities is well known. Similar increases have been realized by adding small quantities of oil to the coal mix. Although it would appear that such procedures provide inexpensive methods for increasing the capacity of existing coke-oven installations, Ramsburg and McGurl4/ point out that this increase is possible only if the additional coal can be carbonized in the same coking time as regularly employed without using abnormally high flue temperatures. This statement is in substantial-agreement with the position of Auvil and others5/ and implies that any change in bulk density may be accompanied by a corresponding change in coking time. On the other hand, a recent review of proposed methods for calculating the time required for carbonization6/ includes a number of equations that completely ignore the effects of variations in bulk density.

Jan 1, 1954

By Bruce McDonald

This report contains the findings of a study to perform a task and skill analysis of roof-bolting operations, with respect to the operational training requirements and to prepare detailed recommendations for the operational training system. The extent of the problem was determined by visiting underground coal mines, interviewing training and safety personnel, observing and interviewing roof-bolter operators, and reviewing present training programs and facilities. In conjunction with the mine visits an extensive literature search was conducted with emphasis on training, mine safety, and accidents involving the roof-bolting operation and roof-bolter operators. A number of training programs and training devices were considered resulting in the development of a recommended training program including training devices to be used and establishing training objectives.

Jan 1, 1977

By O. P. Hood

The spontaneous combustion of coal lies at the bottom of the subject of storage. It is useless to store coal that is to be lost by fire from spontaneous combustion. Every engineer is familiar with the phenomena of the self-heating of coal, yet, for all that, spontaneous combustion is relatively rare. If we counted the times a portion of cod was stored where it would be undisturbed for a few weeks, the number of such storage operations in any one year would mount into the millions. Of these, a relatively small number show the phenomena of spontaneous combustion and time risk per ton is very small. It is extremely rare that in the smaller operations involving; only a few tons there is any heating. There is no spontaneous combustion of anthracite, and very rarely does the domestic consumer of bituminous coal find troublesome heating. The main interest in the subject lies in the large piles needed as reserves for public-service utilities, and the industries. Everyone desires to have directions for storage that are perfectly simple and yet will insure against loss. Unfortunately, the problem is too complicated for a simple solution. Many of the factors involved are difficult to determine, as we have no practical means of quantitative measurement. The factors involve chemistry, physics, and engineering, and the man who is

Jan 1, 1939

By W. W. Adams

In mining coal, the Nation's principal mineral fuel, loss of life has been much lower recently than in earlier years when coal mining contributed so heavily to the industrial-accident death toll in the United States. Particularly notable has been the relatively small number of deaths during the past few years compared with the number that occurred 20 or 30 years ago. Reports received by the United States Bureau of Mines, covering all commercially operated mines that were active during all or any part of the calendar year 1935, showed that accidents during that year had resulted in the loss of 1,242 lives. This death toll, although regrettable, represents a material improvement over the industry's experience during most years prior to 1935, and especially over the industry's worst year, 1907, when 3,242 men were killed. Fewer lives were lost in 1933, when 1,064 men were killed at work, than during any year for which complete figures are available.

Jan 1, 1938

By Oliver C. Ralston

Nonmetallic technologic investigations of the U. S. Bureau of Mines are headquartered at experiment stations in three widely separated localities of the United States. During 1936, the Nonmetals Division of the Technologic Branch was formally set up by combining the direction off the work of these three experiment stations under one administration. The New Brunswick (N.J.) station which in the past has been known as the Nonmetallic Minerals Experiment Station, is henceforth to be at College Park, Md., as part of the Eastern Experiment Station, and its principal activities will be related to the nonmetallic resources of the Eastern and New England States.

Jan 1, 1937

By R. V. Higgins, H. C. Miller

"INTRODUCTION The development of methods for determining the total quantity of crude oil that a given pool could be expected to produce in the future and the well-spacing and drilling programs most likely to result in the recovery of the maximum quantity of oil at the minimum cost became problems of acute concern to American oil producers and petroleum engineers during the second decade of the twentieth century, The United States faced what seemed at that time to be a serious shortage of petroleum, and it appeared that the constantly increasing demand for petroleum and its products could not be adequately supplied. Undrilled prospective acreage, which until then had been plentiful, seemed to be getting scarcer, competition was increasing, the margin of profit to the producer was shrinking, and the need for developing constructive policies of conservation appeared paramount. As a result of physical and economic changes then taking place within the petroleum industry prompted by the seemingly uncertain future, accurate knowledge pertaining to the probable future production of oil wells and of oil lands especially was needed and greatly desired. Furthermore, the need for obtaining the maximum quantity of oil from known fields caused technical information - which up to that time had not been deemed essential to the successful and profitable operation of oil lands - to be sought eagerly. The need for technical information, such as methods for determining future reserves of oil and the rate at which the oil could be obtained under a specific program of drilling, was emphasized further with the passage of the Revenue Act of 1918, and oil producers with enough income to place them in the taxable class were compelled, for the first time, to report their taxable income 4/ to the Treasury Department."

Nov 1, 1939

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr,5 Fieldner and Davis,6 and others, 7 has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M.8 standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting she results in those types of fuel which give erroneous results due to mechanical losses.

Jan 1, 1932