Search Documents

By Suresh K. Bhatt

Although overall worker productivity for U.S. underground coal mines is available, productivity by mining method and seam thickness is not. Mining technology has gone through dramatic changes in the past decade, and the industry has experienced a lack of accurate productivity Figures addressing these changes. This information is of great interest in planning for future mining systems as thick and shallow coal seams currently being mined are depleted and exploitation of thinner, deeper, and better quality seams is considered to partially meet the requirements of the 1990 Clean Air Act Amendments. In a cooperative program, the U.S. Bureau of Mines obtained raw mine level production and related data from U.S. Energy Information Administration for 1989 and 1990 and performed the needed statistical analysis. Base criteria, parameters, and salient results of the mine productivity analysis are presented in this report.

Jan 1, 1994

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Kenneth H. Johnston

For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meetings of the Kansas-Oklahoma Waterflood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1960 spring tour of four waterflooding projects in Greenwood County, Kans. (fig. 1). Three of the projects produce oil from the Bartlesville sand, and one produces from the Cattleman sand. The Bartlesville-sand floods have been in operation from 4 to 12 years and have produced about 3,910,000 barrels of waterflood oil from the injection of approximately 64,715,000 barrels of water, a cumulative water-injected to oil-produced ratio of 17 to 1. The Cattleman- sand flood, which has been operating for 3-1/2 years, has produced about 842,000 barrels of waterflood oil from the injection of approximately 9,305,000 barrels of water, a cumulative water-injected to oil-produced ratio of 11 to 1.

Jan 1, 1960

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By A. L. Peyton

Manganese-oxide minerals occur in irregular pockets distributed through the residual clays of the Cartersville district, which lies 45 miles north-west of Atlanta in Bartow County, Ga. The district produces, or has produced, limonite, barite, specular hematite, ochre, ferruginous manganese, manganiferous iron are, as well as manganese. Bureau of Mines engineers have visited the district on three occasions - in December 1939, February 1941, and October 1942. During the visit of February 1941, 80 tons of samples of manganese-bearing clays were taken from seven properties for ore-dressing tests, which were conducted at the Bureau of Mines laboratory at Rolla, Mo. The. October 1942 visit was for the purpose of reappraising the district in the light of knowledge gained from the ore-dressing studies and to prepare a plan for the district's development. Exploratory drilling was begun in March l943 and was continued until June 1945. Nine properties were explored that, roughly follow a line beginning near Cartersville and extend to a point 2 miles northeast of the village of White. The work consisted of bulldozer trenching, rotary bucket churn drilling, sampling, and analytical determinations. The manganese district is 18 miles long with a maximum width of 7 miles at Cartersville, which lies at the center of the district. The work of the Bureau was confined to the northern half of the district between Cartersville and Pine Log. The properties explored comprise but a small portion of the Potential producing area.

Jan 1, 1949

By A. B. Hooker, L. C. IlsLey

Several ignitions or mine pa, which might have led to explosions, and at least ona mine fire attributed to heated leg wires of electric detonators, have occm.rred. at rn1::.es in which outside shot firing is practiced. Photographs taken at one mine ind.la.ted. that the wires became red hot during firing. These results having been --i·-led. to the .Lttention of the electrical section of the Bureau of the Mines, ignitions the tests and to reportd aid in herein preventing were made future to trouble determine of if this possible kind, the cause of The investigation, which 1• considered preliminary, included tests to determine the conditions tha.t cause gas ignitions from heated. leg wires of electric and. of detonators, copper leg possible wires, remedies The tor samples such of heating, wire used. and in the the relative test were behavior the of reg\llar ironDa. Pont iron and copper leg wires (No, 22 A,W,G.) C\1t from Du. Pont electric detonators.

Aug 1, 1922

By J. E. Pahlman

As part of its effort to reduce the need for strategic minerals through conservation and to reduce the capital and energy requirements of mineral processing, the Bureau of Mines has investigated a method for preparing ferrochromium alloys containing less than 2 percent carbon. This method will conserve chromium and should reduce the capital and energy requirements for chromite reduction. Reduced products containing less than 2 wt-pct C and as low as 0.01 wt-pct C were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 torr and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be supe¬rior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates (Fe,Cr)7C3 and (Fe,Cr)23C6, No evidence of carbide intermediates Fe3C or Cr3C2 was found. Buttons of ferrochrome alloys were made by melting a mixture of reduced products with CaO and Si02 at 1,700° C for 20 minutes in an induction furnace,

Jan 1, 1980

By K. K. Kershner, J. G. Donaldson

This investigation was conducted to obtain data on optimum conditions for chloridizing metal sulfides . Salt- roasting galena at 450° C for 8 hours chloridized 75 percent of the lead ; in an equal time of treatment at 750° C , the process chloridized 42 percent of the zinc in sphalerite . Hydrogen chloride at 500° C completely chloridized galena in 15 minutes , and at 600° C converted all of the zinc in sphalerite to the chloride in 4 hours .

Jan 1, 1963

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX's Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

By Oliver Bowles

Chalk is defined as a noncrystalline, soft, friable, fine-grained, light-colored type of limestone. It consists essentially of calcareous shells of minute organisms known as "foraminifera," although skeletal remains of molluscs, corals, and sponges are also present. Flint balls which are found so commonly in the chalk cliffs of Europe are regarded as segregations of the remains of certain organisms, such as radiolarians and sponges, that secrete siliceous shells or spicules. The famous chalk beds of northwestern Europe are of Upper Cretaceous age, a geological period that was particularly favorable for the develop- ment and multiplication of foraminifera. The distinguishing physical characteristics of true chalk never have been fully defined; probably its noncrystalline and colloidal properties are most important. The properties of chalk, whiting, and whiting substitutes are not well understood, and much re- search is necessary before definite reasons may be ascribed for the behavior of these materials under various conditions of use. The Bureau of Mines has undertaken a detailed study of chalk and similar materials to determine their exact properties and to establish a basis for classifying formations loosely designated as chalk occurring in various parts of the United States, but the results of this study will not be available for some months. Whiting is a pulverized, purified, and carefully sized chalk. Whiting substitutes consist of finely ground limestone or dolomite, ground marble (marble flour), white marl, and chemically precipitated calcium carbonate.

Jul 1, 1931

By F. E. Block

The metallic reduction of vanadium chlorides was investigated by the Federal Bureau of Mines as a possible new route for preparing vanadium metal in an effort to develop a production process that would be adaptable to large-scale plant production and would yield metal of uniformly high quality. Vanadium tetrachloride was usually prepared by chlorinating vanadium pentoxide in the presence of carbon. Although oxygen-?free tetrachloride was difficult to prepare this way, it could be prepared by the direct chlorination of vanadium carbide. Lower valent vanadium trichloride was prepared by the thermal decomposition of vanadium tetrachloride. Vanadium dichloride was also prepared by the thermal disproportionation of vanadium trichloride.

Jan 1, 1961

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By D. J. Singleton

Erosion corrosion of 12 alloys in phosphoric acid waste water was studied by the Bureau of Mines. Tests were conducted on oblate spheroids or cylindrical specimens in 12-and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with a starting pH of 1.6. For comparison, tests were conducted while grinding phosphate rock in plain water. Static corrosion tests in gypsum pond water also were conducted. For all alloys, the wear by erosion-corrosion (milling with gypsum pond water) was greater than the sum of erosion (milling with water) plus static corrosion. Erosion-corrosion wear was about 1,500 to 3,000 mpy for the alloyed white cast irons, 1,000 to 1,400 mpy for commercial steel ball material and type 316 stainless steel, and 600 to 900 mpy for nickel-base alloys and a high-manganese, nitrided stainless steel. Alloy costs per unit of phosphate rock 'processed favor a low-alloy, high-carbon steel or a high-manganese, nitrided stainless steel.

Jan 1, 1985

By Y. Miron

Previous studies at the Bureau of Mines outlined the hazards of ammonium nitrate-fuel oil (AN-FO) mixtures in the presence of pyrite-bearing ores. The recent trend in the mining industry to strengthen AN-FO by the addition of aluminum metal raised the question regarding the effect of aluminum in AN-FO in the presence of pyrite-bearing ore. Laboratory work, similar to that done previously, demonstrated that the temperature of a self-sustaining reaction in the presence of AN-FO ore-aluminum is not lower than that for a comparable AN-FO-ore mixture. However, as might be expected from known thermochemical data, once initiated, the resulting reactions between AN-FO, aluminum, and pyrite are much more vigorous than those observed for AN-FO and pyrites alone. The temperature required to produce a self-sustained reaction for the combinations tested in this study is 250°±20° F while in the previous Bureau study, reactions were noted, in some instances, at 150° F. The different pyritic ores may be the cause of this variation.

Jan 1, 1976

By Dana C. Reinke, David K. I Ingram

Researchers at the National Institute for Occupational Safety and Health partnered with the water well industry to develop engi­neering control technologies and training products to address noise exposure at the job site. Noise­induced hearing loss continues to be a problem in the well drilling industry. Research con­ducted by NIOSH found that air rotary drill rigs produce sound levels more than 90 dB(A) over the course of an eight­hour workday. Sounds levels above 90 dB(A), identified during hammer drilling and the hammering of casing, exposes workers to levels that can damage hearing. A typical air rotary drill rig provides no barrier, for noise and dust pro­tection, between the drill’s control panel and the drill stem. The development of a partial cab is the clearest example of NIOSH’s research partnership with the water well industry. NIOSH researchers determined that an engineering noise control to protect the oper­ator at the rig’s control panel would be effective, based on typical work site conditions. Many surface rigs do not have full cabs as a result of the original equipment manufacturer design or the high cost of aftermarket products. Developed as a partial cab, the NIOSH engineer­ing noise control design addressed stakeholders’ needs associated with cost, transport, and worker usage (Figure 1). Field tests found the partial cab effective in reducing sound levels at the rig’s control panel, a typical location for a drill rig operator. Sound levels at the control panel were reduced from 104 to 96 dB(A) (Figure 2). Coupled with continued use of personal protective equipment, such as hear­ing protection devices, the partial cab can help to reduce noise exposure. NIOSH researchers created a CD with informa­tion about noise exposure and the partial cab. Most important to well drilling companies is information on how to construct and attach the partial cab to drill rigs. The CD can be viewed on a standard computer and includes a video of the partial cab in use on a work site. Computer­aided design drawings are included on the CD and provide detail of the cab design as well as information on construction mate­rials and design details. Additionally, the CD provides background infor­mation on noise­induced hearing loss and hearing protection devices to increase knowledge about this occupational health concern. This information can be viewed by all company employees to help promote the partial cab’s importance to workers using the cab. More information on the partial cab noise control technology can be downloaded from www.cdc.gov/ niosh/mining NIOSH researchers also examined the health and safety training needs of workers in the ground water industry. It was quickly realized that most workers learn health and safety on the job and do not attend any sort of formal training. In addition, there is not a lot of time for daily “tailgate talks” or “shop talks” on health and safety issues. As a small business industry, the owner is often operating a drill rig along with his other employees. In general, new employees learn the job in an apprentice style sys­tem. As a result, workers and owners have few opportunities to access uniform health and safety information based upon the job — an outdoor work environment with daily change in work sites. With this information, NIOSH researchers devel­oped two products that deliver health and safety information to fit into the daily work of well drillers. Both are information circulars and are available through download at www.cdc.gov/niosh/mining and the NGWA Web site at www.ngwa.org/publication/ publications.cfm. These circulars are: Water Well Safety Bits. This booklet provides information in a “quick bites” style. It is pre­sented in a magazine format and can be left on

By J. Roger Loebenstein

This report presents a U.S. Bureau of Mines study of the flow of arsenic-containing materials in the United States, based on the best data available in 1991, includes a consideration of arsenic as a byproduct of the processing of nonferrous metals, the fate of arsenic in manufacturing wastes, the quantity of arsenic used in products, tile fate of arsenic in dissipative uses, and the useful life of discarded products. Where possible, estimates are given of the amounts of arsenic lost from the materials flow. Arsenic byproduct of mining nonferrous metals. Historically, most U.S. production has been from the states of Montana, Washington, and Utah. The smelters in these states are believed to be the areas of the country where arsenic is most concentrated in the soil, tailings ponds, and waste dumps. Since the closure of the last domestic producer of arsenic in 1985, all arsenic has been derived from imported sources. Historically, arsenic was important in agricultural applications as an insecticide, herbicide, and cotton desiccant. As the environmental movement gained momentum and the toxicity of arsenic became better understood, most of the agricultural uses for arsenic were banned. Beginning about 1975, the use of arsenic as a wood preservative began to grow. After 1980, wood preservative uses became more important than agricultural applications. By 1990, 70% of the arsenic consumed in the United States was used by the wood preservative industry and 20% by the agricultural industry. The major source of domestic arsenic emissions in 1989 was from the U.S. copper processing indus¬try. About 7,800 mt/yr of arsenic was discarded in leach dumps, tailings, and slag. Another 800 mt/yr was liberated to the atmosphere and 1/100 mt/yr was exported in copper concentrates. On the consumption side, 9,200 mt/yr was lost, mostly from dissipative agricultural uses and the disposal of obsolete arsenical products.

Jan 1, 1994

By W. E. Miller, G. S. Scott, G. W. Jones

"INTRODUCTION One of the major activities of the Bureau of Mines is the promotion of safety in mining and the mineral industries. Research is undertaken in connection with these problems to determine the explosion and ignition hazards of combustible gases, liquids, and solids and to investigate means of reducing them.Occasionally the Bureau is asked to determine inflammability or ignition temperatures to enhance safety in nonrnineral industries. From time to time it has complied with such requests when no other agency was available to do the work and the investigation could be conducted with a minimum of time and expense. The present investigation is one of this class.Nicotine (C10H14N2), a colorless combustible liquid having a boiling point of 246°C, is usually obtained from tobacco and its products by extraction processes. When heated to its boiling point it decomposes; the purified product is obtained from tobacco extractions by distillation at reduced pressures or is distilled in a current of inert gas.It has an unpleasant odor, a burning taste, and in the undiluted state is highly toxic. Under certain conditions it can be oxidised to nicotinic acid and in the near future may therefore become of considerable economic importance. Nicotinic acid is a component of the vitamin B complex now commonly used to fortify white flour and other foods that normally are deficient in these vitamins."

May 1, 1942

By A. U. Miller

"Ventilation is one of the meet important factors in mining, although until recent years less thought has probably been given to effective ventilation than to any other one phase of mining. In the past, very little, if any, attention was given air courses until they became so constricted by falls that the volume of air was greatly reduced; and, in addition, the stoppings and doors were so poorly constructed that only a very small percentage of air reached the face workings.As a matter of fact, mines have been visited where the volume of air being circulated in certain sections was much larger than in others, and where the management was striving to increase the flow of air in those sections with the least air current, believing the ventilation to be deficient. After sampling and analyzing the return air from the various sections in such mines it has been found that the quality of the air in certain places with the largest flow was more impure than in some of those with the least flow.In past years, practically all mine fans were operated by steam-driven engines supplied with steam from the mire boiler plant. No check was made on the steam consumption or the power cost of operating the fan, therefore the management had very little if any definite information as to cost of ventilating the mine.With the increased use of electrically-driven equipment in mines electricity is being used more and more to drive mine ventilating fans, and since in many instances the current is purchased from central power plants operators have come to realize that in many cases the cost of operating the fans is very high. Some engineers estimate that it ranges from 20 to 50 per cent of the total power cost of the mine. This information, together with the fact that mines are now being developed on a larger scale, requiring larger quantities of air for the men to dilute the gases liberated, has caused the large progressive companies to make, a more comprehensive study of mine ventilation, resulting in a decided improvement in the quality and quantity of air at the face workings, as well as reducing materially the ventilating costs."

Oct 1, 1930

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971