Search Documents

By R. L. Schmidt

One of a series published by the Bureau of Mines covering research investigations in rock drillability, this report of field drilling results extends earlier laboratory findings and provides a relatively simple procedure for predicting percussive drilling rates with reasonable accuracy. Two percussive drills mounted on a truck were used to drill a total of 25 rock types, and the results were used to develop a prediction equation. The equation was tested on a set of unrelated laboratory percussive drilling data, and the comparison between predicted and actual rates is shown in tabular form.

Jan 1, 1972

By J. R. Hauger, P. A. Romans, W. J. Niebuhr

With suitable instrumentation and techniques it is possible to determine the presence of tantalum in columbium to 20 ppm . This paper discusses the selection of X- ray spectrographic instrumentation and describes a technique for accomplishing the low level determination of tantalum . An ion- exchange method of separating tantalum from columbium is also described .

Jan 1, 1964

By H. Kenworthy

The investigations described in this report were undertaken to demonstrate, on a laboratory scale, the possibility of recovering several million pounds of tin plus tungsten contained in stockpiled and currently rejected slags from the Longhorn tin smelter at Texas City, Tex. At the same time, it was anticipated that the treatment procedures developed might be applicable to slags from other tin-smelting operations. Results of the laboratory work show that it is possible, by pyrometallurgical means, to separate the tin and tungsten into products of intermediate grade that may be returned to the smelter circuits for further upgrading. Several methods of treatment were investigated. The methods that proved effective were: Fusion reduction, chloride volatilization, sulfide volatilization, and carbide formation. Over 90 percent of the tin and tungsten could be removed from the slat by any of these methods. Each type of treatment has advantages and disadvantages, and it could not be determined from the small-scale work which method was the more meritorious. Tungsten and (in some types of treatment) tin-bearing products were diluted by iron, the separation of which will require additional studies. Prevention of a portion of the iron from reporting with the tin or tungsten is a distinct advantage and possibility that will require inure laboratory work to develop the needed techniques for its accomplishment. Tin products from single treatments of stag ranged up to 75 percent in tin content but were more generally under 35 percent. Tungsten products were usually under 15 percent; but segregated portions could be selected, at a sacrifice in recovery, that contained up to 50 percent tungstic oxide equivalent.

Jan 1, 1957

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By Raja V. Rarnani, Robert L. Frantz

More than 100 scientists from diverse professional backgrounds have contributed their expertise to the Dust Center as investigators. Approximately 50 researchers served as principal investigators, with responsibility for directing the work on Center projects, from experimental design and implementation in mines and in laboratories to coordination of efforts within the research infrastructure of the Center. The professional biographies which follow demonstrate the breadth and depth of research capabilities brought to the Center by its principal investigators.

Jan 1, 1995

By W. L. Zeigler

This paper describing the milling practice of the Hecla Mining Co. is one of a series being prepared by the United States Bureau of Mines. The concentrator of the Hecla Mining Co., which utilizes combined gravity and flotation methods, is located at Gem, Shoshone County, Idaho, about 2 miles south of the Hecla mine at Burke. It has a maximum capacity of 900 tons per day and all ore treated is drawn from the company's Hecla mine. Milling ore for 1910 contained 9.7 per cent of lead, 1.2 per cent of zinc, and 4.77 ounces of silver per ton.

Jan 1, 1932

By D. S. Kingery

This study describes five fatal accidents so unusual in occurrence that the chain of circumstances bringing them about may never be duplicated. The intent of this publication is to illustrate that everyone working underground is subjected, at all times, to definite inherent mining hazards and that safety devices, though provided, often are ineffective or not used. It is hoped that a study of these fatal accidents in bituminous-coal mines will show workers and safety engineers that nothing can be taken for granted. Safety planning with continuous study can prevent these unusual accidents as well as the routine recurring types, which cause the majority of coal-mining injuries. The treacherous, fatalistic philosophy that "it can't happen to me" or that "when my time's up I'll get it regardless of what I do," still prevails among individuals and even safety engineers. The individual or safety man who believes in luck as applied to safety should not read any further, since this study was written for the sincere, safety-minded individual who accepts the prevention of all accidents as a challenge to his knowledge, initiative, persuasiveness, and salesmanship.

Jan 1, 1954

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By W. P. Diamond

The Bureau of Mines has been involved in the drilling of vertical, horizontal, and directional coalbed gas drainage boreholes for mine safety since 1964. In that time, boreholes have been drilled in most of the major coal regions of the United States under a wide variety of geologic conditions. Many of the geologic conditions that occur in the coal measures are detrimental to gas drainage; others may be beneficial. Analytical techniques to determine the gas content of coal samples and evaluate regional trends of gas distribution have been developed. Drilling techniques that maximize the acquisition of coalbed gas data and geologic information have been determined. Although some of the geologic factors influencing the placement and potential success of coalbed gas drainage boreholes have been reported in papers on individual projects, a complete, systematic compilation has not previously been available. The objective of this paper is to pro- vide information on specific geologic factors that should be considered prior to, during, and after the drilling of coalbed gas drainage bore-holes. Many of the commonsense considerations that have been learned through many years of Bureau of Mines experience, but have generally not been reported formally, are included for those who may be considering coalbed gas drainage drilling for the first time, or who have not had the opportunity to encounter a substantial number of geologic situations.

Jan 1, 1982

By E. R. Palowitch

This report stems from a study by the Bureau of Mines of the possibility of reducing coal filter-cake moisture by applying radiant heat directly to the filter cake while under vacuum during the drying phase of the filter cycle. One disk of a 4-foot-diameter vacuum filter was equipped with gas-fired radiant-heat generators and the effect of radiant heating on the moisture content of a variety of filter cakes was studied. The results of this investigation show that this process can best be described as a filter aid capable of increasing the effectiveness of conventional filtration approximately 6 percentage points of moisture. The operating cost of removing water by this method is somewhat lower than the average operating cost of thermal drying and is considerably cheaper when the total cost is considered. Removal of water from coal that has been wet-cleaned is an important part of the overall coal preparation process. Water is a contaminant, and it is foolish to wash coal to reduce its ash content and add inert water in the process. In some instances the removal of water is actually more important than the removal of ash-forming minerals; its weight adds to the cost of transportation, and its evaporation during burning or carbonizing absorbs useful heat. Fine coal that contains more than about 10 percent moisture is notoriously difficult to handle. A problem thus exists for which there are sound practical and economic reasons to seek a solution.

Jan 1, 1961

By Martin H. Stanczyk

Acid leaching of selected copper sulfide minerals, impure copper sulfide flotation concentrates, and a cement copper precipitate at elevated temperatures and pressures was investigated. Copper extractions of 97 to 99 pct were obtained by leaching chalcopyrite and the flotation concentrates with water under oxidizing conditions at 200° C for 30 to 60 min. In tests with bornite, chalcocite,and cement copper, addition of sulfuric acid or pyrite to the autoclave was required to obtain similar copper extractions. The chemistry of leaching copper minerals was studied. It was determined that different copper sulfides altered to covellite as one step in their dissolution.

Jan 1, 1963

By Warren E. Morrison

This study was prepared in response to the need for a series of data that reflect the basic flow pattern of energy resources in the United States. To effectively measure and analyze energy,2 it is necessary to prepare balances that reflect both production and consumption, and the various forms energy resources take at different stages of utilization. Before energy can be measured it must also be put into a common unit. In this study the common unit us d is the British Thermal Unit (Btu). The ideal point to survey energy is at the stage of final ultimate use, representing the useful work derived from the interaction of energy inputs and the prime mover. Unfortunately this concept of efficient or useful work from energy output cannot readily be measured in the aggregate. With the present available official data, energy measurement can be carried to the point of calculation of net inputs of energy3 into the economy at various stages of utilization. However, preparation of energy balances, on a net basis is hampered by the fact that this can only be done for years when the censuses of Mineral Industries and Manufactures are taken, usually at 5-year intervals.

Jan 1, 1964

By John D. Sullivan, Edward P. Barrett

The experimental work on the utilization of tin-plate scrap at the North- west experiment station of the U. S. Pireau of Mines in cooperation with College of Mines, University of Washington, necessitated the selection of a simple method for the determination of tin in the iron produced. Some of the standard methods for the determination of tin which were tried are given below: 1. Dissolving in acids and precipitating the tin as sulphide, igniting and weighing as Sn02. 2. Dissolving in aciis, reducing with nickel, cooling in an atmosphere of carbon dioxide, end titrating with standari iodine solution. 3. Dissolving in acids, precipitating the tin as sulphide, dissolving this sulphide in H3 and H2S04, heating until fumes of 503 are evolved, reducing with nickel or sheet lead, cooling in an atmosphere of carbon dioxide, ani titrating with a standard iodine solution.

Mar 1, 1923

By M. M. Hassan

This report describes the analysis tools developed at West Virginia University which can be implemented to optimally design coal mine electrical systems. The basic analytical tools for all power systems are the load-flow and short-circuit analysis. Well known programs have been developed for analysis of ac transmission and distribution systems, but they are not applicable to a system which has combined ac/dc distribution, such as a coal mine power system. Furthermore, the topology of a coal mine electrcal system changes continuously due to the movement of the locomotives on the track. In the first section of this report, algorithms for carrying out load flow and short-circuit analysis of a coal mine electrical system are described. Results from the study of a typical coal mine system are presented. In the second section a method is described to optimally size power cables for cyclic loads. The method is based on the development of a thermal-electric model for a low-voltage power cable. Results from experimental verification of the model are also presented. These techniques are useful in the safe, efficient, reliable and economical design of the coal mine electrical power systems.

Jan 1, 1979

By Walter Kawa

In connection with its research in producing synthetic liquid fuels from coal, the Federal Bureau of Mines studied reactions of iron and iron compounds with hydrogen and hydrogen sulfide in batch autoclaves. The Bureau hoped to gain indirect evidence regarding the chemical changes that iron catalysts undergo when they are used in the hydrogenation of coal. The information obtained may be helpful in identifying the active form or forms of iron catalysts. At 450° C., with hydrogen at hundreds of atmospheres and hydrogen sulfide at 1 or 2 atmospheres, the thermodynamically stable form of iron is ferrous sulfide in the case of the metal, magnetite, ferric oxide, ferrous sulfate, ferrous oxalate, or the chlorides of iron. However, complete conversion to ferrous sulfide was not achieved at temperatures of 400° to 500° C. for kinetic reasons. Extensive sulfiding of iron, magnetite, ferric oxide, and ferrous oxalate occurred below 400° C., and some conversion of ferrous sulfate to ferrous sulfide occurred at 400° C. In the hydrogenation of coal, ferrous sulfide is the form of iron likely to be available for heterogeneous catalysis when starting with the metal, oxide, sulfate, or oxalate.

Jan 1, 1960

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

By R. G. Sandberg

The Bureau of Mines investigated a hydrometallurgical procedure to recover gold, silver, and byproduct lead from a complex lead-zinc sulfide ore. A ferric chloride (FeCI3) preleach, at 40° C in 6 h, extracted about 50 pct of the zinc and formed insoluble silver and lead chlorides. Subsequent acid thiourea leaching, for 1 to 3 h at 40° C, extracted about 85 pct of the gold and silver. Lead chloride was solubilized from the remaining residue with NaCI brine solution at 55° C in 1 h. Lead metal was recovered from the brine solution in an electrolytic cell with an anion perms elective membrane at a current efficiency of 95 pct and current density of 100 A/m2. Spent FeCl3 leach solution was reoxidized in the anode compartment at a current efficiency between 75 and 95 pct.

Jan 1, 1986

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By Arel B. McMahan

The U.S. Bureau of Mines investigated 21 mines, prospects, and mineralized sites in and adjacent to a 38,713-acre portion of the 255,058-acre Kingston Range Wilderness Study Area in 1983. The study area is 35 miles north of Baker, CA in the Mojave Desert. Mineral deposits in and adjacent to the study area are in altered carbonate rocks intruded by diabase sills near monzonite porphyry contacts. Monzonite porphyry forms the core of the Kingston Range and underlies about 70 percent of the study area. Sedimentary carbonate rocks are exposed in bands on the north and east boundaries and as isolated roof pendants in the southeastern portion of the study area.

Jan 1, 1986