Search Documents

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By R. L. Marovelli

ANTICIPATING the eventual use of the huge tonnages of nonmagnetic taconites of the Mesabi range of the United States, the Federal Bureau of Mines is classifying and evaluating these deposits in detail. This introductory report describes work begun in 1954 as part of a long-range program to sample, classify, and evaluate important occurrences of nonmagnetic taconite on the Mesabi, range. Included in this report are brief discussions of the geology, history, and potential of the Mesabi range district and mining industry, together with a more detailed presentation of the sampling and metallurgical evaluation of these nonmagnetic taconite deposits. A total of 898 field samples was collected. Most of these were taken in the region between Grand Rapids and Chisholm, Minn., but a few came from the area between Chisholm and Buhl, Minn. Of the total samples, 865 were from open pit bank faces where the greater vertical distances presented by the cherty members facilitated the taking of a large number of samples. Conversely, the narrow face presented by the slaty members confined and limited the areas from which samples were taken. In addition, 33 of the field samples were taken from rock dumps in order to determine, in a preliminary way, the characteristics of these materials.

Jan 1, 1961

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

The Bureau of Mines performed cratering experiments in a homogeneous granite to test scaling laws for charge weights of 0.00476, 0.0220, 0.0900, 0.304, and 1.03 lb. Agreement among the data was best when empirical scaling exponents greater than one-third were assumed. Although the analysis showed that the best empirical scaling exponents were 0.37 for crater volume, 0.38 for crater radius, and 0.39 scaling for crater depth, all three crater dimensions could be scaled with a 0.38 scaling exponent.

Jan 1, 1970

By Charles Prasky

The objective of this investigation by the Bureau of Mines was to determine the response to sulfatization of diverse low-grade manganiferous materials in the iron formation of the Cuyuna district. In line with this objective a bench-scale sulfatizing procedure was developed that was less expensive and more rapid than pilot-plant methods. Samples from the central and south- western parts of the North range were tested. Results of evaluating a total of 46 pelletized samples, originating in areas with an estimated potential resource of 94 million long tons with a manganese content of 7 percent, indicates that approximately 87 percent of the manganese may be recovered as a synthetic manganese ore. This is equivalent to more than 12 million long tons of a metallurgical-grade ore, containing 46 percent manganese. It is anticipated that a premium product, containing over 50 percent manganese, may be obtained by sulfatizing procedures. This report is part of a continuing investigation5 6 of Cuyuna iron range manganese deposits in Crow Wing County, Minn. Lewis and coworkers describe the manganiferous iron formation in the bedrock of the Cuyuna district and include a description of a high-temperature differential sulfatizing process for recovering a ferrograde manganese product. The low-grade manganiferous

Jan 1, 1961

By R. S. Fowkes

The degree and manner of packing of bulk materials influences all phases of their loading, such as by a front end loader or a dragline, and their mechanics of flow, such as through a binhopper or an ore pass. The most important quantity in analyzing the handling of a bulk material is its shear strength which depends primarily on the same parameters as those that determine the packing state. Some of these are size, size distribution, moisture content, particle shape, particle orientation, and cohesion. The variables that affect the packing state arc vibration, pressure, intensity of deposition, velocity of deposition, and, when the material is confined, container used. The analysis of packing by a number of investigators has been done almost entirely with spherical particles. Most of these studies have dealt with monosized spheres. There is scant information on particles with angular shapes. Since most of the investigations by far have been concerned with ceramics and powder metallurgy, the particle sizes and ranges of size distribution have been small compared to those generally found in mining after fragmentation.

Jan 1, 1974

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By A. J. Kraemer

This report on the physical and chemical properties of typical crude oils of California is the 'eighth in a series on the producing districts of the United States. It includes discussion of results, tabulated data, and individual analyses of typical California crudes. Additional analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, end Ventura Counties will be published later in another Serial of the Bureau, but the summary tabulations are presented here. The samples represented in this report were collected over a rather wide interval of tine, the early samples having been obtained during the fall of 1919, and the most recent ones dating from the summer of 1923. It is thought that the samples are fairly representative, both of the older settled production and of the new flush production of the southern California fields.

Jan 1, 1924

By Bill M. Stewart

To decrease the potential for fine coal waste slurry impoundment failures, the Bureau of Mines investigated a new disposal technique. The fine coal waste slurry is rapidly thickened (i.e., dewatered) and deposited on a slightly sloping surface. To accomplish rapid dewatering, a chemical flocculation system using polymers was developed to treat the fine coal waste slurry stream. The fine solids formed flocs, settled from suspension, and rapidly released excess water. During the last 5 days of the field test, slurry flowing at rates from 498 to 675 gal/min with a specific gravity range of 1.15 to 1.33 was successfully treated and dewatered. During this period, untreated slurry had an average moisture content of 227.4 pct (30.7 wt pct solids). The effectiveness of the dewatering system was determined by monitoring the moisture content of the deposited waste with respect to time. Sixty-five hours after ending the field test the average moisture content was 54.9 pct (64.5 wt pct solids); 68 days after the field test the average moisture content was 28.8 pct (78.0 wt pct solids).

Jan 1, 1986

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li20-A1203-4Si02), a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Hills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade deposits in forth Carolina. The theoretical lithia (Li20) content of spodumene is 9.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By T. L. Muldoon

The bagging of dry pulverized products using fluidized air packers creates severe respirable dust problems in many surface mining operations. During bag filling, excess air and product blows by the bag valve/nozzle interface. After bag ejection, dust blows out of the bag valve. During conveying and handling dust is released from the bag valve and dirty bag surface. Overexposure of the bagging machine operator and bag handlers is common. This report describes the development and testing of a new dust control system for bagging machines. The system features a new bag clamp design to reduce product blowby during filling. A controlled vacuum system removes excess air from the bag before ejection, eliminating the problems after bag ejection and during conveying and handling. The system has shown significant reductions in dust exposure for both bag machine operators and bag handlers. These reductions are achieved with no significant effect on total mill productivity.

Jan 1, 1985

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By Green R. E.

The removal of silica from commercial iron oxide concentrates by dissolution with sodium hydroxide was investigated by the Bureau of Mines as a means for producing supergrade concentrates. The effects of strength of solution, temperature, and digestion time on the extraction of silica were evaluated using eight iron oxide concentrates. Silica extraction from the eight concentrates was enhanced by autoclave leaching in the temperature range of 150° to 250° C and varied from 70 to 95 pct depending on the concentrate used. Superconcentrates containing less than 2 pct Si02 and more than 69 pct Fe were made only when magnetite concentrates were leached in the autoclave. The investigation showed that it is not difficult to obtain a supergrade product if the gangue is mainly quartz.

Jan 1, 1973

By S. M. Runke

An ever-increasing demand for beryllium and beryllium alloys has directed attention to the milling of low-grade domestic deposits as a possible means of supplying part of the Nation's ore requirements. The United States generally produces less than 10 percent of its annual supply. For example, new supply in 1953 was estimated at about 9,250 tons, of which the United States imported 8,500 tons. Domestic production was only 750 tons.2/ Since record high prices for beryl in 1952 and 1953 did not greatly increase domestic product ion, the United States must develop mechanical beneficiation processes to use low-grade deposits and reduce dependence on foreign sources

Jan 1, 1954

By A. L. Engel

The Stayton Mining District in San Benito County, Calif., near Hollister, includes several square miles with many occurrences of antimony ore. The sample submitted for the test described in this paper came from a vein said to have been traced and sampled for 5,000 feet on the surface, 1,500 feet carrying 2-1/2 to 3 percent antimony and the remainder 1/2 to 2 percent. Thirty thousand tons 'With a content of 3 percent antimony are said to be blocked out. A drift of 200 feet on the vein has shown ore containing 4.2 percent antimony. The present sample assayed 3.8 percent. Previous flotation investigation of this are resulted in a recovery of only 71.6 percent in concentrates containing 56.8 percent Sb. It was desired to develop a method of treatment that would give better results. The antimony in the sample occurred as the mineral stibnite, Sb2S3, antimony sulfide.

Jan 1, 1949

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By E. G. King

Heats of formation of three crystalline oxides of rhenium (Re02, ReO3 and Re207) have been determined by the method of solution calorimetry, using an aqueous perchloric acid--ceric perchlorate solvent. Copper metal and cupric oxide were utilized as auxiliary substances. Heats were determined at 298' K for the reactions Re + 2CuO = Re02 + 2Cu, Re + 3CuO = ReO3 + 3Cu, and 2Re + 7CuO = Re207 + 7Cu. Standard heats of formation were derived using the value of -37.23 ±0,15 kcal/mole as the heat of formation of CuO. The standard molal heats of formation of the rhenium oxides were determined: Re02, -107.3 ±0.8 kcal; ReO3, -140.8 ±0.9 kcal; and Re207, -301.9 ±1.8 kcal.

Jan 1, 1969