Search Documents

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner's pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world's supply of the' material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity'of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By Albert W. Deurbrouck

The performance characteristics of five hydrocyclone coal washers were evaluated to determine the sharpness and efficiency of separation that might be anticipated in commercial operation. The hydrocyclone overflows contained generally good clean coal products that would require little re-treating to remove misplaced high-gravity material. The underflows, however, contained from 63.6 to 36.7 percent of misplaced low-gravity material, which would require secondary cleaning to provide acceptable clean coal yields.

Jan 1, 1974

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state, Adsorbed gas is stored in the micropore structure and its transport is governed by Fick's law. The free gas occurs in the. fracture system and flows according to Darcy's law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds.

Jan 1, 1969

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned & name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled except the deep holes drilled to test geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By Jonathan E. Ludlow

A field test was conducted to demonstrate and quantify the relationship between deep cutting and the creation of airborne respirable dust for longwall mining With a double-ended ranging drum shearer. The testing program was carried out on the 3 North longwall of North American Coal Company's Quarto No. y mine in Claringten, Ohio. Continuous recordings of the dust levels were made at both the midface and tail ate areas. Data were collected during 27 shifts during which time 81 complete mining, cycles took place. Both drum speed and the number of picks per line were varied systematically during the testing program to alter the depth of cut while the production rate was held constant by maintaining a constant haulage speed. The test results indicated that at the midface position, airborne respirable dust was strongly dependent upon the depth of cut as influenced by both the drum speed and number of picks. Drum speed had a much stronger effect than number of picks over the experimental range, since a halving of drum speed reduced dust levels by approximately 60 percent while removal of every other vane pick resulted in only a 2.1 percent reduction at constant production. At the tailgate position, however, neither effect was strongly apparent. A tendency for the slower drum speeds to he associated with reduced power consumption and higher haulage speeds (and therefore production rates) was also noted. It is recommended that longwall operators oper¬ate at the lowest available drum speed wherever possible.

Jan 1, 1981

By Walter E. Pittman

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

Jan 1, 1982

The object of this program was to design and build a self-contained system for remote monitoring of the atmosphere in mines. The system developed uses the mine pager phone line as the primary communication channel and also has the capability of using 208 Hz in the ELF band for wireless transmission through the earth. The depth for through-the-earth transmission is expected to be about 80 to 90 meters in high conductivity soil and is limited by the noise level in the ELF band-pass filters. The underground components of the TEM System are energized by mine power through a battery charger - storage battery power supply. In the event of mine power failure the battery capacity is more than sufficient for one week's operation with interrogations every four hours.

Jan 1, 1980

By W. T. Benson

The Bureau of Mines has examined selected deposits of titanium minerals throughout the United States. The titaniferous magnetite deposits in the western San Gabriel Mountains, Los Angeles County, Calif., were among those selected for study, and in 1956-58 field work was conducted to determine the extent and character of the titaniferous magnetite deposits occurring in the area. This report describes this work and summarizes earlier work in the area by the Bureau and others. The titaniferous magnetite occurs disseminated as seams and lenticular pods in an anorthosite belt 4 to 6 miles wide that trends about. N. 80° W., extending from sec. 13, T. 3 N., R. 12 W., to the west boundary of R. 14 W., at which point the titaniferous magnetite-bearing rocks disappear beneath the sediments in the Santa Clara River Valley.

Jan 1, 1962

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

By Gregory Molinda

NIOSH has recently completed a study of the interaction between polyurethane (PUR) and coal mine roof in order to determine the mechanism of reinforcement, in both highly fractured rock and unfractured rock. Four case studies of PUR rein­forcement are presented. At a West Virginia site, a borehole camera revealed the location of roof voids and guided the PUR injection. By injecting polyure­thane into a zone from 0.6 to 1.8 m (2?6 ft.) high in the roof, a roof beam was created and ongoing intersection falls were halted. In another highly fractured roof in a western Pennsylvania mine, a total of 5.8 cm (2.3 in.) of rubbleized rock was found in a zone up to 3 m (10 ft.) into the roof. Untargeted PUR injection filled approximately 1/2 of the fractures. These two case studies showed that it is not necessary to fill up 100% of the void space to create stability. In the other two field sites, polyurethane was injected into weak, but unfractured roof. Post-injec­tion video monitoring showed that weak bedding planes were hydraulically wedged open and polyure­thane injected along bedding. The reinforcement value of this injection method is limited because of the wafer-thin layer of PUR introduced along bedding, and the lack of a PUR ??webbing?? which would serve as a structural framework to provide strength. It was determined that video inspection prior to PUR injection can aid in identifying the fracture zones to target, and minimize ??blind?? pumping and loss of PUR.

Jan 1, 2008

By Rupert O. Yantz

This report, authorized under contract Number H0111403 Amendment Number One, entitled, "Exploration of Illumination Concepts for Underground Coal Mines", contains the results of an investigation of methods, procedures, and technology for providing working place lighting in underground coal mines and construction of a prototype, man portable, mine illumination system and a prototype, machine mounted, mine illumination system for use in high and low coal entries of underground coal mines.

Jan 1, 1972

By Harry E. Tufft

Data were obtained by the writer from a number of the large coul-mine operators in Illinois, on the consumption and cost of timber used in their mines and the quality of the timber now being used as compared with former years. This information supplemented by comparative date for previous years published in bulletins of the filinois Coal Mining Investigation series, and other sources, is presented below. This survey is part of a cooperative study with the . S. Forest Service, of the mine timber situation, with particular regard to the economies to be derived by better selection, preparation, and storage of timber, and especially treatment with preservatives to prolong the life. Geo. S. Rice, chief mining engineer of the J. S. Bureau of Mines, under whose general direction the work was done, gave valuable advice and criticism. R. B. Miller, State Forester, contributed helpful data which he had recent- ly obtained in an independent study of the mine-timber situation in Illinois.

Apr 1, 1923

By T. Kessler

Spark-source mass spectrometry has been used to determine the amounts of minor and trace elements in coal particles of various sizes, including the respirable range (<5 microns). Fifty-six elements ranging in concentration from 0.1 ppm wt to 5,000 ppm wt have been determined. The investigation of coal and coal ash has shown that the organic material in coal does not interfere with the spark-source determination of the various elements.

Jan 1, 1971

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts

By Gerald P. Scanlan

Control of the dust produced by continuous mining machines in coal mines is generally obtained by water sprays from fixed nozzles mounted on the frame of the machine in back of the cutting head. Mounting the nozzles on the rotating head of the machine closer to the coal cutting bits may improve the efficiency of dust suppression. To test this concept, respirable dust measurements were made during 39 regular production shifts in an underground mine using a Joy 11CM continuous miner. The equipment used, difficulties encountered, and measurements obtained are described.

Jan 1, 1974

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 40 ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 40 ft.

Jan 1, 1992

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962