Search Documents

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By Francis Church Lincoln, Paul Zinner

"Attention of the Bureau of Mines was first directed to the Gray farm area by the results of several exploratory churn-drill holes completed by the New Jersey Zinc Co., and later by Roland J. Teske and by Judge H. L. Heer.When the Bureau of Mines initiated its investigation of the area, all drilling on the Gray farm had been discontinued, and no mining had resulted from the exploratory work. However, in the opinion of the Illinois Geological Survey, the Federal Geological Survey, and the Federal Bureau of Mines, this drilling,with the preliminary geological studies, was considered sufficient evidence to justify continued exploration to the southeast along a projection of the trend of mineralization developed in the mines to the northwest, or the so-called Black Jack Trough.This report describes the work done and presents the data obtained during the period of Bureau of Mines exploratory work.In its program of exploration of mineral deposits, the Bureau of Mines has as its Primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision or Dr. R. S. Dean, assistant director.Special acknowledgment is due Paul Herbert, geologist, Illinois Geological Survey, for his studies of cores, which greatly influenced the planning and progress of the exploratory work. Acknowledgment is also made to A. F. Agnew and A. V. Heyl, geologists, Federal Geological Survey, for their invaluable aid; to 0. W. Terry, F. C. Lincoln, M. H. Berliner, A. M. Cummings, project engineers; and to E. P. Barrett, district engineer, Minneapolis, and E. D. Gardner, regional engineer, Rolla, Mo., for supervising the program.The Gray ore body is on the Gray farm 5 miles south of Galena in Jo Daviess County, northwestern Illinois. The location with respect to adjoining properties is shown on figure 1. Galena is a city of 4,000 population on the banks of the Galena River, a stream that was formerly navigable by Mississippi River steamers but has now shrunk to the dimensions of a small creek. A gravel road leads from the city to the Gray farm and onward to the Bautsch and Boevers farms to the south of it."

Sep 1, 1946

By Eugene T. Sheridan

The 25th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, disclosed that 79 companies produced and sold peat from 81 operations in 21 States in 1958. Peat is a carbonaceous deposit, formed under water or in a water-saturated environment from plant material. It is the first stage in the development of coal and, when properly dried, can be used as fuel. Although 98 percent (estimated) of the total world production is used for energy purposes, the status of peat in the United States is somewhat unique in that none is used for fuel, and practically all is consumed as an agricultural product, chiefly for soil improvement purposes. The domestic peat industry has expanded rapidly since World War II, and production in 1958 was 327,813 net tons valued at $3,445,767. More than one-half million ton of peat was consumed in the United State in 1958, however, as 269,096 tons was imported.

Jan 1, 1959

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By L. O. Bacon, H. R. Joesting, J. H. Getz

"INTRODUCTION For a number of years manganiferous iron ore has been mined on a small scale at Boston Hill, in Grant County, N. Mex. Total production up to 1943 is estimated to be over 793,000 long tons, containing 8 to 35 percent manganese and 26 to 46 percent iron. 4/ During 1941 to 1943 production was estimated to be 206,000 long tons, containing about 13 percent manganese and 37 percent iron. During 1944 daily production was several hundred tons, mostly from a single open pit. Several moderately large deposits have been mined: and many smaller ones have been found.From February to April 1945 geophysical surveys were carried out on Boston Hill by the Division of Geophysical Exploration, in cooperation with District 5, Central Region, Bureau of Mines, to determine if hitherto undiscovered manganiferous iron deposits exist. Field work was interrupted for a total of about 1 month during this period by work on other projects in nearby areas. Previous to the geophysical surveys, a preliminary examination was made by H. R. Joesting to determine if geophysical methods could be utilized in exploring the area. 5/Field measurements were made by L. O. Bacon and J. H. Getz, project geo¬physicists of the Bureau of Mines, under the general supervision of H. R. Joesting. A grid survey of the area, to locate geophysical stations, was made by Paul Russell, Bureau of Mines engineer, who also collected specimens for laboratory tests. Most of the computations and the preliminary magnetic and resistivity maps were made by L. 0. Bacon."

Feb 1, 1948

By William A. Beck

The K.T. Dome Mine in Owen and Henry Counties, Ky., has been operated intermittently under several different owners since the early nineteen hundreds. No record of total production is available, but it is said that during 1943 and 1944, while being operated by the Twin Valley Mining Co., 30 cars of zinc concentrates and 10 cars of lead concentrates were shipped. The vein can be traced for about 10 miles along the strike from Lockport, Henry County, to Big Twin Creek in Owen County. It pinches and swells both vertically and horizontally and is reported to average 20 inches in width. In order to develop additional reserves on the property, the Bureau of Mines drilled four holes on the south extension of the vein. Drilling disclosed that the vein dips to the west on the south side of the Kentucky River and is continuous along the strike and in depth. However, the extent of mineralization in the vein varies widely.

Jan 1, 1949

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

Maps To Accompany Bulletin 418

Jan 1, 1941

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Perform laboratory tests to measure the vibration attenuation characteristics of off-road vehicle operator seats for various types of seat suspensions, cushions, and seat adjustment settings. Background A study was conducted by the U.S. Bureau of Mines to determine the probability of whole-body vibration (WBV) exposure for a large class of off-road machinery operating in surface coal mines. The study determined that mere than 40 pct of off-road equipment operators were exposed to WBV exceeding the standard fatigue-decreased-proficiency (FDP) level defined by the International Standards Organization in its guideline ISO standard 2631. The tire-terrain interaction of a moving vehicle generates vibrations that are transmitted through the ve¬hicle suspension, cab mounting, and seat. The final point of transmission of vehicle vibration to the operator is through the scat. A seat that provides good vibration isolation and allows good vehicle control is of prime importance to operator safety and health.

Jan 1, 1993

By R. V. Higgins

This paper describes a method and a computer program for calculating shape factors and areas of channels that turn more than 90° and conduct fluids into the backs of wells. The program represents an improvement over a previous Bureau of Mines investigation by using a 4-point Lagrange interpolation equation instead of a 3-point and by summing areas of trapezoids with either x altitudes or y altitudes. Some of the techniques reported in this paper can also be used to compute the areas between contours and the lengths of lines that turn more than 90°.

Jan 1, 1968

By C. R. Bopp, N. A. C. Smith

"For a period of several years, beginning with 1915, there has been a continuous change in the quality of motor gasoline. The average volatility has decreased, this to the fact that higher boiling fractions of the crude oil have been included in the gasoline. This change in quality was made necessary by the tremendous increase in the demand for motor fuel, caused by the development of the motor car, and during the war was an absolute necessity to avoid gasoline shortages. The Bureau of Mines has kept in close touch with this situation by making surveys from time to time of the gasolines sold throughout the country, as this information is of value to manufacturers and users of motor cars and also indicates when any changes are required in the Government specifications. The Bureau has just completed a gasoline survey and is in a position to make public the fact that there has been very little change in the quality of motor gasoline in recent months.During the period from January 17 to February 3, 1920, 81 samples of actor gasoline were collected by representatives of the Bureau of Mines in seven districts of the United States. The cities selected for this survey were New York, N. Y., including Brooklyn; Washington, D. C.; Pittsburgh, Pa.; Chicago, Ill.; New Orleans, La.; Salt Lake City, Utah; and San Francisco, Cal., including Berkeley. In every case the samples collected were taken in such a manner as to represent material actually being sold as motor fuel, and to include samples from each refinery marketing in the district."

Jan 1, 1920

By G. L. Fitzpatrick

Preliminary results of an experiment in seismic holography indicate that the techniques of acoustical holography may be successfully used with seismic waves to determine the size and general shape of underground objects. This experiment was carried out under field conditions on a moderately large scale compared with the typical laboratory experiments in acoustical holography. The object to be mapped was a 100-foot-diameter, spherical, low-velocity zone of explosively fractured rock in oil shale at an average depth of 80 feet. The seismic wavelength of the Fourier component wave used in making the seismic holograms was 50 feet at a frequency of 140 cps. The hologram sampling aperture was 226 feet square and was sampled by 441 geophones in a 21 by 21 rectangular array. One novel aspect of the experiment was the use of a wide-band polychromatic explosive source of seismic waves rather than a narrow-band quasi-monochromatic vibrator source. A successful laser reconstruction of the object image from a lensless Fourier-transform hologram in the form of a 5/l6-inch-square photographic transparency is illustrated. The size of the underground object measured from the laser reconstruction of the object and the size inferred from a knowledge of the amount of explosives used to fracture the site and the tensile strength of the oil shale are found to agree.

Jan 1, 1972

By G. W. Grove, E. E. Quenon

"INTRODUCTION During September, October, and November 1946 the Safety Division of the Bureau of Mines, off' the United States Department of the Interior, Pittsburgh, Pa., tested four new types of self-contained breathing apparatus and approved them in accordance with Schedule 13C. Approval was granted with the proviso that certain specifications outlined on the approval plate be made fully effective, and with the understanding that established safe practices in training in the care and use of self-contained breathing apparatus are of major importance.The excellent records made during the past 30 years in the safe use of self-contained breathing apparatus, some of which required the almost continuous wearing of apparatus during several hours daily for days, weeks, or months, may be attributed largely to the Bureau's system of rescue organizations, selection of physically fit rescue workers, effective training, and educational work done in rescue and recovery operations during fires or following disasters and in the care and use of self-contained breathing apparatus. Loss of life during wearing of breathing apparatus was due almost invariably to poorly assembled or otherwise defective apparatus, poor physical condition of the wearer, or insufficient training or some incorrect procedure.The newly developed breathing apparatus are of much simpler design than the conventional type used for the past several years; however, it is just as important to select rescue crews carefully and to train them properly in the care, use, and limitations of the new types of apparatus as for the older long-established types, if anything like safety is to be achieved in using them. The Bureau of Mines considers that 1/2-hour and 3/4-hour self-contained breathing apparatus should be used only as auxiliary equipment in mine rescue and recovery work, and their capabilities and limitations should be well understood by those who wear them."

Jul 1, 1947

By John D. Bradley

Stibnite is 76 miles east of Cascade, Idaho, which is 78 miles due north of Boise. The altitude at Stibnite is 6,500 feet, and between Cascade and Stibnite the Forest Service road crosses two summits - Big Creek at 6,800 feet and Warm Lake at 7,300 feet. The ownership of most of the Meadow Creek group of 190 claims, which is optioned by the Bradley Mining Co from the United Mercury Mines Co. may be traced back from their consolidation by the United Mercury Co. through ownership by prospectors and small promotional companies to the discovery of the Thunder Mountain district in 1900 by the Caswell brothers.

Jan 1, 1942

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

This is an audience, I know, that shares my interest in a subject that is currently getting a lot of attention -the tendency of our Nation to draw increasingly on overseas supplies of certain mineral commodities, and proportionately less on domestic sources for these minerals. That we do obtain substantial quantities of some essential minerals from abroad is easy to demonstrate. That we will continue to do so in the foreseeable future is not in doubt. Uncertainty begins, however, when we try to interpret the significance of these facts. As with many phenomena, their meaning is open to a variety of interpretations.

Jan 1, 1980

By E. G. King

Strontium sulfide and barium sulfide occur as intermediates in commercial treatments of the impure natural sulfates to produce pure strontium and barium chemicals. Thermodynamic considerations involving these sulfides have been hampered by lack of basic data, such as the entropies at 298.15°K. This paper reports the results of heat capacity measurements of strontium sulfide and barium sulfide in the temperature range 50°-298°K. The entropies at 298.15°K. were derived from the heat capacity values. Free energies of formation at 298.15°k. were computed from the entropies and literature values of the heats of formation. Strontium sulfide and barium sulfide are thermo-dynamically less stable than calcium sulfide, but more stable than magnesium sulfide.

Jan 1, 1960

By B. B. Letson, D. F. Smith, T. E. Gardner, A. R. Taylor

Low- temperature heat capacities of strontium chloride (7° - 300° K) and strontium fluoride ( 11 ° - 300 ° K) were measured with an adiabatic calorimeter . Smooth values of heat capacity , entropy , enthalpy function , and free - energy function were calculated from the heat - capacity data . The smooth values are reported at 10 ° K intervals and at 273.15 ° and 298.15 ° K.

Jan 1, 1963