Search Documents

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By James C. Barker

A uniquely mineralized area extends from northwestern Canada through Alaska into eastern Siberia. Some of the metals found there are relatively rare in the conterminous United Stales. Among these are cobalt, the platinum-group metals, and chromite. Geologic evidence suggests that cobalt and the platinum-group metals may be present in deposits that could constitute nationally important reserves. Chromite in potentially minable deposits is known, but it may be relatively less abundant. Limited reserves of these metals have been delineated, but most of the favorable terranes and reported occurrences throughout the vast expanse of Alaska remain unexplored. As part of the mineral studies mandated under the Alaska National Interest Lands Conservation Act, the Bureau of Mines' Alaska Field Operations Center and the Bureau's research centers at Albany, Oreg., and Reno, Nev., are cooperating in a long- range program to investigate occurrences and delineate reserves of cobalt, the platinum-group metals, and chromite in Alaska. Studies of other critical and strategic minerals will be phased in during succeeding years, as ongoing projects are completed. This first in a series of annual reports summarizes available information about deposits and past production of cobalt, the platinum-group metals, and chromite, and describes current and planned Bureau investigations of these minerals.

Jan 1, 1981

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube's deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support's resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

By Jack Wasserman, Don Wasserman, Gretchen Hinton, Logan Mullinix, Shekar Khanal

Human testing has always been a needed way to provide information on the effects of vehicle vibration, however, the manner of testing has not reflected the real situations of driver’s hands on a steering wheel and a seat with back support and driving tasks. The typical system have used a standard sinusoidal excitation rather than the typical types of road – truck excitations The new truck driver training simulators provide the combination of road roughness, speed effects, cab environment and individual tasks. The system has a full six axis simulation potential. The simulators have the protection of the individual by a combination of two ways for the individual to stop the motion as well as an operator with visual capability who can stop the testing. The closed simulator, shown in Figure 1, has the potential for providing motion during the operation.

Jan 6, 2006

By R. L. Balmer

This information circular, which describes the methods and costs of sinking a small underground shaft with steel supports at the Keystone mine of American Smelting and Refining Co., near Crested Butte, Colo., is one of a series being prepared by the Bureau of Mines on current shaft-sinking practices in various mining districts of the United States. Preparations for sinking a combined exploration, development, and production shaft from the lowest level of the Keystone mine began early in 1957. This vertical, three-compartment, 6-1/4-by 16-foot rectangular shaft was to be sunk in separate stages or lifts so as to correspond with the progress of an associated lateral exploration and development program. The first section of the shaft was collared and sunk to a depth of 209 feet between September 1957 and April 1958. Because of the depressed base-metal market, the mine was shut down as soon as the initial phase of the exploration and development program had been completed and before any deeper sinking could be attempted.

Jan 1, 1962

By O. M. Bishop

"SUMMARYAs a result of the increased demand for fluorspar during the war, the Bureau of Mines investigated numerous fluorspar properties in the southern Illinois field, which is centered in Rosiclare. Among these the J. J. Shelby 40-acre tract on the western edge of the district presented favorable factors that caused it to be chosen /or exploration.H. G. Spiller, formen lessee of the property, had explored the Shelby vein by means of an adit level and winze, and showed it to contain goad values in zinc and fluorspar at the depth explored. A diamond-drill hole with which Spiller explored the vein 78 feet southwest of the winze, however, failed to cut ore. After studying the field evidence, the Bureau concluded that the vein merited further exploration, particularly at a depth of about 440 feet, where the Fredonia limestone would form the foot-wall of the vein and the hanging wall would be the competent Cypress sandstone.Between October 17, 1944, and March 26, 1945, three diamond-drill holes were bored for a total inclined depth of 1,592 feet. Holes 1 and spaced approximately 500 feet apart, explored the vein at 440 feet 4 below the surface. The economic mineralization existed in the vein where cut. Hole 3 cut the fault at approximately 300 feet below the outcrop but failed to find any vein matter except stringers of calcite with small amounts of pyrite."

Apr 1, 1947

By Charles L. Kimbell

For the world mineral industry as a whole, the year 1981 was a period of continuation and, in some instances, an acceleration of negative trends extending back into 1980. Most available statistical data reflected stagnation or downturns in activity. Levels of production, trade, and consumption declined for a substantial number of leading mineral commodities, including, most notably, steel and petroleum. Investment, if not lower than in 1980, was evidently increasing at a more modest rate. Prices for major mineral commodities were generally lower, at least in terms of constant dollars, and in some cases even in terms of current dollars. Prospects of a major reversal of these patterns seemed dim. The mineral industry, however, was far from alone in this general downturn; most other elements of the national economies of the world's nations fared little better. General conditions of inflation, recession, and reduced industrial product consumption were reflected in most other sectors of the total economy. International political events continued to influence mineral output and flow but had less influence on overall levels of activities than on the geographic distribution of these activities. The Iran-Iraq war certainly played a role in reducing mineral industry activities in those nations, but the commodity most affected, petroleum, was available from other sources in sufficient quantity that, in the face of reduced demand, a substantial surplus developed.

Jan 1, 1983

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By M. G. Zabetakis

This publication presents a simplified graphic method for determining the explosibility of mine atmospheres under mine-fire conditions from mine- atmosphere composition data. Sometimes it is necessary to seal part of a mine during a fire to exclude air and thus extinguish the fire. Unfortunately, liberation of methane and formation of hydrogen and carbon monoxide in the sealed area may create an ex- plosive or flammable atmosphere if enough oxygen is present to support combustion. On the other hand, the oxygen concentration may be reduced through combustion processes and the concentration of inert gases (nitrogen and carbon dioxide) increased enough to render the atmosphere within the sealed area non-explosive. Before an area is unsealed, it is extremely important to know if the sealed atmosphere contains Flammable gases in proportions that might form explosive mixtures when air is introduced. If an explosive mixture forms and the fire is rekindled, a gas explosion will result. Various experimental methods may be used to determine the explosibility of a particular mine atmosphere; however, these methods usually are impracticable in the field.

Jan 1, 1959

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By C. P. Hood

"The amount of ash in anthracite coal interests every buyer, and occasionally produces caustic comment, but there is a lack of authentic figures that will take the subject out of the realm of opinion and agitated fancy and. give a true picture of the quality of coal actually delivered. What per cent ash is to be expected when the coal is good, and when have we a right to make serious complaint?During the past summer the Bureau of Mines took 127 samples of 1000 pounds each, representing nearly 30,000 tons of anthracite is dealers' yards in seventeen cities in the State of Massachusetts. There were three objects in view, to discover the average and the variation in amount of ash in anthracite in some easily described area; to demonstrate standard sampling methods, and to learn something about the feasibility of itinerant coal sampling. Massachusetts was selected because its principal cities could be visited in a single season. There also appeared need for demonstration of standard sampling of coal, since a coal quality law had been passed in the State, to be administered by those unfamiliar with coal sampling."

Feb 1, 1924

By G. W. Birge

Carbonizing properties of the principal coal beds of Butler County, Pa., are described in this report by the Bureau of Mines. Eight samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Clarion, and Brookville beds, were carbonized at 900° C. by the Bureau of Mines-American Gas Association (BM-AGA) method. Butler County coals rank as high-volatile A bituminous and are generally characterized by high sulfur content compared with Appalachian coals used for industrial coking. If cleaned, the Brookville and one sample of Upper Freeport coal would be acceptable as the major component of metallurgical coking blends. The other Butler County coals tested would be unsuitable for this purpose because of either excessive sulfur or poor coking properties.

Jan 1, 1962

By E. C. Lane

[This Is the ninth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the interior. The first report gave data on motor gasoline sold during the winter of 1935-36.3/ The Present report presents analytical data for 2,033 samples, representing the products of approximately 80 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data that were average by the Pacific Coast Technical Group before 'being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. The cumber of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, arc as follows: Regular price, 1,066 samples, 208 items, and 49 brands; premium price, 575 tamales, 154 items, and 38 brands; third-grade gasoline, 7;4 samples, 150 items, and 53 brands. The meanings of these terms as used in the surveys tar as follows: Sample: The individual supply of gasoline obtained at the filling station and analysed in the laboratory.]

Jan 1, 1940

Provide reasonably priced, reliable fire protection for large walking draglines. Approach Fire hazards on large draglines were analyzed, then appropriate automatic fire sensing and suppression systems developed and in-mine tested. How It Works Five fire hazard areas identified for special attention are: electrical control room, high voltage transformer enclosures, circuit breaker rooms, collector ring/roller path area, and the automatic lubrication rooms. Automatic fire sensing and suppression systems were separately designed for each area. The design of each system was tailored to the hazards and equipment protected. Spot thermal sensing and Halon 1301 suppression were specified for the electrical

Jan 1, 1981

By Michael G. Pojar, John K. Ahlness

"The copper industry has had a long and interesting history associated with leaching, involving vat, dump, heap, and in situ methods. The Bureau of Mines has also had an interest in copper leaching and has researched the techniques of solution recovery, particularly concentrating on in situ methods. In situ mining is a relatively low cost method and has been proven commercially successful by nine operations. It has been most commonly used for final recovery in old workings at the conclusion of conventional mining operations.This report brings together information about 10 commercial in situ operations as well as 14 experimental projects. These 24 sites comprise most of the in situ copper mining activities that have taken place in the United States. Background information, geology, ore preparation, solution application, and recovery and processing are provided for each operation. Production data and tables summarizing the engineering statistics for each operation and an extensive in situ mining bibliography are included. INTRODUCTIONThe purpose of this Bureau of Mines report is to summarize the documented in situ copper leach mining activities that have taken place in the United States. It was prepared to provide a source of engineering and operating data upon which future in situ copper mining activities can be based. Twenty-four different sites are discussed. These are all of the sites that are known to the authors from the extensive in situ copper leach mining bibliography developed at the Bureau's Twin Cities (MN) Research Center (Appendix B).In situ copper leach mining activities fall into the following categories:1. Commercial operations with ore body preparation.2. Commercial operations in old mine workings.3. Experimental programs.Ore body preparation includes such activities as blasting, block caving, and hydraulic fracturing (hydrofracing) specifically to fragment the ore body. Operations in old mine workings include those done in open pits, worked out block caved areas, and backfilled stopes where leaching is done as an afterthought to conventional mining. Experimental programs are small-scale tests of the feasibility of a commercial operation. Some of these programs did not progress to the point where leach solutions were applied to the ore.Each operation (locations shown in figure 1) will be discussed in terms of background information, geology, ore preparation, solution application, recovery and processing, and engineering and production data. Information was collected from published reports, communications with company personnel, and site visits."

Jan 1, 1982

By L. W. Higley

Electrowinning metals from solutions leached from low-grade ores is becoming an increasingly important extraction method as the metal industry turns to pollution-free recovery processes. Lead-alloy anodes are used industrially in the electrolytic recovery of zinc and copper. However, associated with the use of these anodes are the inherent problems of stability and lead contamination of the cathode. In an effort to eliminate these problems, the Bureau of Mines has developed a relatively inexpensive lead dioxide anode for electrowinning metals from strong acid solutions. The anode was prepared by depositing Pb02 directly on a titanium blank in a strong HN03-Pb(N03)2 solution at 2.15 to 6.45 A/dm2 and 60° C. This anode was tested in zinc and copper electrowinning cells containing 200 gpl H2S04 and 35 to 100 gpl metal ions at the current density of 3.23 to 6.45 A/dm2. Contamination of the cathode by lead was =0.005 pet. A 30-day test at 6.45 to 12.90 A/dm2 in an electrolyte containing 200 gpl H2S04 and no metal ions resulted in a slight change in surface morphology of the Pb02 anode but no measurable change in anode weight or dimensions.

Jan 1, 1976