Search Documents

By W. J. Fene, H. B. Humphrey, J. J. Forbes

"INTRODUCTION Loss of life from coal-mine explosions in the United States in 1949 was the lowest in any year since before 1870. Although fatality reports from coal nines before 1910 were incomplete,' the explosion fatalities from single disasters or individual States exceeded the 1949 total in each year as far back as 1870, when the records become fragmentary. Since 1890, the only other year in which fewer than 35 were killed was 1946, with a total of 32. Figure 1 shows the total yearly fatalities from explosions in all coal mines and those in anthracite mines alone since 1870. The fatalities in bituminous coal mines were not completely reported before 1910, but enough reports were issued by major coal-producing States to compile reasonably representative figures back to 1885. Any corrections would be additions to these totals.The reason for the moderate total of 46 explosion fatalities in 1948 and the low total of 8 killed in 1949 is thought to be the serious and careful attention devoted to elimination of coal-mine explosion hazards after the disastrous explosions in 1947. The standards now being observed generally with respect to ventilation, rock-dusting, and inspections for gas are better than those found earlier in even the mines having the best reputations for safety. Exceptions are still numerous, but they are fewer, month by month, because of the pressure of Federal and State inspections and a changing conception of the hazards that should not be permitted underground. The prevailing precautions have not eliminated all ignitions of gas or dust, but they have limited propagation to small explosions and have prevented serious loss of life.The number of ignitions (14) reported for the year was less than the average (24) for the 5 years 1944-48 and only half the average for the fiscal years 1929-44. Another favorable factor is that Bureau of Mines representatives were probably in closer contact with both small and large mines in nearly all coal-mining districts. Inspectors now assigned to individual districts are better able to keep informed on the happenings and the progress of safety in their districts. In 1948, one-fourth of the explosions were in mines that employed fewer than 10 men; this condition was duplicated in 1949."

Jul 1, 1950

By R. W. Van Dolah

The feasibility of formulating cap-sensitive slurry explosives for use in underground mines with potentially flammable gas atmospheres was examined. Formulations containing aluminum metal as sensitizer and sodium chloride to reduce incendivity were prepared; some were cap-sensitive and had adequate air-gap. Flaked aluminum metal rather than the atomized type proved to be the more effective sensitizing agent of the formulations tested for incendivity in the large gallery of the Bureau of Mines, some were found to be suitably nonincendive.

Jan 1, 1968

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the comparative effectiveness of three wet dust control techniques for face drilling. Previous attempts to achieve effective dust control on face drills with dry collectors have not met with success, the largest problem being sustained effective dust capture at the face. Results show that (1) foam-through-the-drill can provide 95-pct average total dust reduction in gypsum; (2) water mist-through-the-drill can provide approximately 91-pct average total dust reduction and 93-pet average respirable dust reduction in salt; (3) external boom-mounted water sprays can provide approximately 50-pet average dust reduction for both total and respirable dust in salt. The investigation showed that (1) foam and water in small quantities are very effective dust control techniques for face drills when applied through the drill steel at the point of dust generation, and (2) boom-mounted water sprays are only minimally effective for dust control on face drills.

Jan 1, 1981

By John Gross

"Introduction.Southern Illinois and Kentucky are credited with approximately 90% of the fluorspar production of the United States. A small amount of high-grade acid, spar is obtained from the ore by band sorting; the greater part, however, is recovered by jigs and tables as gravel spar containing approximately 85% calcium fluoride. In the jigging and tabling operations, galena is recovered, and enough silica and calcite are removed to raise the calcium fluoride content of the gravel spar to 85%. However, the removal of silica and calcite results in a large loss of spar. With increasing depth in the mines, zinc sulphide, sphalerite, is encountered in increasing quantity and the removal of this has become a serious problem. While the sphalerite can be fairly well removed from the spar by present milling methods, a marketable zinc concentrate can not be made. The experiments described below were made on fluorspar ore from Southern Illinois, by the mining experiment station of the U. S. Bureau of Mines, at Rolla, Mo., in cooperation with the Missouri School of Mines and Metallurgy.The ore tested contained. 7.3% lead, 27.9% zinc, 35.7% calcium fluoride, 9.5% silica and 4.7%. calcite.Tests and Results. In some preliminary tests it was noticed that a portion of the finely crushed ore adhered strongly to the sample pans, and upon investigation it was found that the adhering material was practically clean spar. By utilizing this property of adhesion 46.8% of the spar was recovered as a product containing 98.3% calcium fluoride. This suggested the possibility of using electrostatic separation."

Jul 1, 1921

By W. P. Yant, R. R. Sayers

The rather sudden increase in the use of methanol as an antifreeze for automobile radiators has caused considerable comment , with some anxiety to persons interested in industrial and public health , regarding the possible health hazard in dispensing and using the product . In view of this , the chemical industry interested in the manufacture and marketing of methanol requested the Bureau of Mines to make an impartial and extensive investigation of the hazard involved . With the assistance of the industry this investigation is now in progress and will extend throughout the present winter . When these observations are finished a complete report will be made . At present , however , the acute interest in the problem and the many inquiries that have been received from manufacturers of methanol , garage owners , the automotive industry , public health officials , and private persons demands a brief statement relative to the reasons for the recent availability of methanol for antifreeze purposes , the plan of the bureau's investigation , and the trend of the results of the investigation obtained to date .

Dec 1, 1930

By Thomas M. Barczak

The U.s. Bureau of Mines is conducting research to optimize the utilization and design of mine roof support systems. This report describes methods to evaluate resultant loading on longwall shields, defined as external resultant vertical and horizontal force acting on the canopy and base. Four models are considered: two rigid-body models, an elastic model, and a numerical model. The rigid-body models equate measured internal shield forces to unknown external resultant shield forces (loads) through rigid-body analysis of static equilibrium requirements. The elastic model develops a solution to shield mechanics by evaluation of the load-displacement relationship and stiffness characteristics of the support structure. The numerical model is a two-dimensional finite-element representation of a shield structure. Model determination of resultant shield loading is compared to controlled loading of a shield in the Bureau's mine roof simulator. Parameters investigated are shield height, canopy contact configuration, canopy and base horizontal constrainment, and boundary conditions imposed by vertical and horizontal shield displacements. It is concluded that rigid-body models are most applicable to in situ measurement of shield loading. Applications requirements and potential error sources are discussed.

Jan 1, 1990

By Aleksandar D. Bugarski, Robert J. Timko

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

By Gertrude N. Greenspoon

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) held public hearings in early 1975 on proposed standards for exposure to inorganic arsenic. The findings obtained at the hearings will be considered to promulgate emission standards. Domestic Production.-Arsenic trioxide (As203) was produced domestically only at the Tacoma, Wash. copper smelter of ASARCO Incorporated. Production data cannot be published. Output rose 9% over that of 1974, shipments were less than half those of 1974, and stocks rose 31 %. Production of arsenic metal, begun by ASARCO in August 1974, continued in 1975.

Jan 1, 1977

By Charles B. Carpenter

In general terminology, the West Texas Permian Basin comprises the area south of the Texas Panhandle and west of the Bend Arch or Central Basin region. It is outlined mere definitely by geologists, however, as that area underlain by the south half of the Permian Salt Basin4/ and includes Scurry, Mitchell, Sterling, Howard, Glasscock, Reagan, Crockett, Upton, Midland, Martin, Gaines, Andrews, Ector, Crane, Pecos, Ward, Winkler, and Loving Counties in Texas, and Lea and Eddy Counties in New Mexico. The oil fields of the area, of which more than 70 have been discovered, are shown in fire 1. Approximately 4,200 producing oil wells have been drilled in these fields. Oil has been produced from limestones and dolomites of Permian age in most of the fields in the West Texas Permian Basin. Some of the fields produced oil from sandstone beds above the limestone, and in two fields production has been found below the limestone in formations of Ordovician age.

Jan 1, 1936

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By M. M. Wong

Beryllium possesses attractive properties for use in the nuclear and space fields. Since fused-salt electrorefining can be employed to produce this metal in high-purity form from low-grade or scrap metals, the Bureau of Mines investigated electrorefining of beryllium in electrolytes composed of a LiC1-KC1 eutectic mixture plus varying amounts of BeC12. Results showed a 99- percent or better reduction of oxygen and magnesium and a substantial reduction of other minor metallic impurities. Extremely pure beryllium metal was produced. Operating variables, including BeCl2 concentration in the bath (3.5 to 16.5 mole-percent), temperature of operation (450° to 550° C.), and cathode current density (45 to 770 a,/sq, ft.), were studied; their effects on the deposition of metal, working condition of the bath, and purity of the refined metal are discussed. The safety precautions used in handling beryllium in the laboratory are also described.

Jan 1, 1962

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By John Durkin

The Bureau of Mines has conducted field studies in coal mines through- out the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coalfields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10-pct false alarm rate, the expected probability of detecting a miner's signal from a depth of 1,000 ft is 54 pct; at 500 ft it is 95 pct. These depths exceed the actual depths of 90 pct and 50 pct, respectively, of U.S. coal mines. Sensitivity studies have shown that at a depth of 1,000 ft, for every 3 db of improvement in signal-to-noise ratio, the probability of detection increases 6 to 8 pct.

Jan 1, 1982

By M. Shabbir

A study was made to determine the optimum conditions for precipitation of uranium from mill solutions using hydrogen peroxide. Precipitation tests were made on both synthetic and actual mill solutions. Parameters studied included amount of hydrogen peroxide, initial pH, reaction pH, time, and temperature. Also investigated was the effect of varied amounts of vanadium, molybdenum, and sulfate in the test solution on uranium precipitation and product quality. The optimum conditions for complete precipitation and high product quality were (1) the use of 150 percent of the stoichiometric requirement of hydrogen peroxide, (2) initial pH of 1.0, (3) reaction pH between 3.4 and 5.0, (4) 4 hours reaction time, and (5) ambient reaction temperature. The excess hydrogen peroxide requirement is partially dependent on the amount of impurities present in the feed solution. The hydrogen peroxide process appeared applicable to treatment of the several mill eluate and strip solutions tested. The experimental studies also indicated that the hydrogen peroxide technique gives substantially better product quality than that produced by ammonia precipitation.

Jan 1, 1974

Reduce the time, complexity and expense of dissolving metal and mineral samples in solution in preparation for chemical analysis. Approach In earlier research, the Bureau of Mines developed a rapid and inexpensive method for the dissolution of mineral and metal samples in plastic pressure bottles heated in a boiling water bath. Using this technique, samples could be prepared for chemical analysis in less than one hour compared with several hours by traditional dissolution methods (see Technology News No. 85, December 1980 for further details). By heating in a microwave oven, sample dissolution time can be reduced to approximately 5 minutes.

Jan 1, 1983

By Stephen P. Holt, John A. Bowsher

A preliminary examination of the mica deposits in Culberson and Hudspeth Counties , Texas , was made in September 1942 by A. B. Needham, district engineer of the Bureau of Mines . The deposits were reexamined by R. C. Redfield , associate mining engineer of the Bureau in November 1942, at which time he was accompanied by Philip S. Hoyt , geologist , and J. C. Moore , foreman of the Texas Mica and Feldspar Company . Exploratory work was started on February 16 , 1944 , and terminated on April 30 , 1944. A crew of 4 to 10 men was employed under the supervision of the authors .

Feb 1, 1947

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rub¬ber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber.A sample of gasoline was obtained from the tank in which Cunningham met his death. Examination by Dr. E. W. Dean of the Petroleum Division of the Bureau of Mines gave the following results.This shows the gasoline to be heavy and typical of the gasolines sold throughout Colorado for motor fuel A. Salvus half hour oxygen apparatus was arranged with the breathing bag only in a gas tight box in which the space was kept saturated with the vapor of this gasoline. The main part of the apparatus was outside the box. Oxygen from the apparatus was breathed by a man in the usual manner. Gas samples were taken from the box at intervals to determine the concentration of gasoline vapor, also samples of the oxygen breathed were taken from a side tube in the mouthpiece. The room temperature was 75°F. The concentration of gasoline vapor in the box at the beginning of the test was 4.3%. The man breathing from the apparatus thought he detected gasoline in his oxygen in two minutes after starting the test. Analysis of the inspired oxygen at this time showed 0.03% gasoline vapor. The same man remained on the apparatus for 18 1/2 minutes without suffering any ill effects. His place vas then taken by another man who wore the apparatus until the oxygen was exhausted without noticing more than a trace of gasoline at any time. At the end of the test the inspired oxygen contained 0.07% gasoline vapor. The total time of test was 38 minutes."

Dec 1, 1919

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By Steven W. Schmauch

The Sugarloaf RARE II area (No. 5296) covers 11,100 acres in the northern part of the White Mountain Range, in the Inyo fictional Forrest. It is in Nevada, about 45 mi north of Bishop, California. A mineral survey was conducted by On U.S. burro of Mines in 1982 and by the U.S. Geological Survey in 1980-1982. The Bureau reviewed pertinent literature, searched Esmeralda and Mineral County mining records, obtained current claim information from the administrative agencies, and contacted claim owners. Thirty-six properties were examined, and 674 samples were taken from them to help assess win oral resources and potential. The Geological Survey evaluated the regional mineral potential by geologic, geochemical, and Geophysical surveys.

Jan 1, 1983

By Loren R. Anderson

This is an Appendix of Volume I. In contains the results of the electric cone penetrometer soundings from the second phase of the testing program.

Jan 1, 1982