Search Documents

By Donald N. H. Chi

This Bureau of Mines report is concerned with a theoretical study of the aerodynamic response of a single mine entry to flame-induced disturbance. The unsteady, one/dimensional, compressible flow equations were solved using the method of characteristics. This study was primarily undertaken to determine the feasibility of extending the method of characteristics to study the aero-dynamic response of complex mine networks. It was demonstrated that although the technique has merit in studying the complex wave interaction in single entries, it appears to be too unwieldly and too expensive for network analysis. Effort was also directed at a further study of the dispersion and filtering characteristic of aerodynamic disturbances in mine passageways.

Jan 1, 1975

By Robert E. Johnson

THE MILDEST recession of the postwar period ended in the first months of 1961, and the economy climbed steadily during the remainder of the year. The Federal Reserve Board (FRB) Index of Industrial Production climbed from a low point of 102 (1957=100) in February to 115 in December, a rise of 12.5 percent. But economic activity for the year as a whole was only 1.5 percent higher than the 1960 level, as measured by real gross national product (GNP). Although activity increased throughout 1961, much of it was merely regaining ground lost in the decline during the second half of 1960 and the first months of 1961. The FRB index did not re ain the July 1960 high of 110 until June of 1961. Mineral fuels did not fully share in the economic recovery. The (FRB) crude oil and natural gas index rose only 5 percent between February and December. Although the index of monthly coal production increased 11.5 percent during the year, the February level was so low that total production for the year was the lowest since 1954. Total production of energy measured in Btu's was up slightly (1 percent) during the ear. Coal production was down; production of crude oil and natural gas was up. Calculated consumption paralleled production-total up slightly, coal lower, and crude oil and natural gas higher. The most interesting product developments were in coke and residual fuel oil. Sales of coke showed a sharper drop than steel

Jan 1, 1962

By Elizabeth A. Johnson

The effect of slag composition on lead losses to slags and on the behavior of associated accessory elements in lead blast furnace smelting has been studied by the Bureau of Mines. Equilibrations of 30 g of lead and synthetic slag doped with Cu, In, TI, and Sb at 1,200° C in CO-C02 atmospheres revealed the importance of the FeO:Si02 ratio and the basicity ratio, (CaO+MgO):SiO2, of the slag. Lead losses to slags increased with an increasing FeO:Si02 ratio and decreased with an in-creasing basicity ratio. Copper and indium distribution coefficients, [Lx =] increased from 15 at the lower basicity ratios to near 60 at higher basicity ratios. LTI values increased from 20 to 150 as slag basicity increased. Lcu, Lin, and LTI were relatively in-dependent of the FeO:Si02 ratio, but increased with greater amounts of accessory elements in the system. Antimony distribution alone was shown to be strongly affected by FeO:Si02 ratio, although data were scattered. LSb values ranged from 20 to 800 and decreased sharply with increasing FeO:Si02 ratios. The basicity ratio and the level of accessory element load did not have any noticeable effect on LSb.

Jan 1, 1983

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall employment and injury experience for coal mines-bituminous, lignite, and anthracite; coke, petroleum and natural gas; and peat and slag plants; metal and nonmetal mines; sand and gravel operations; stone quarries; metallurgical plants, including metal mills and smelters; and nonmetal mills for 1959. Volume I of the yearbook contains injury experience and employment data in the metal, non-metal, sand and gravel, slag, and quarrying industries, and the milling operations and related plants. Volume II contains the injury experience and employment data in the fuel industries--coal, coke, petroleum and natural gas, and peat. Surveys conducted by the Bureau of Mines were the source of injury and employment data used to compile the tables and furnish information for the accompanying text. Response to the surveys was voluntary except that for coal mines. The Coal Mine Safety Act requires operators of coal mines to furnish the information requested.

Jan 1, 1960

By Launa G. Mallett, Kathleen M. Kowalski, Michael J. Brnich

The characteristics of leaders under the duress of an emergency are important in the development of emergency planning, training, and in the management of an actual emergency. Knowledge of human behavior is an important component in the formation of emergency strategies. The U.S. Bureau of Mines analyzed the leadership behavior in three underground mine fire escapes. The subjects described their escapes during open-ended interviews. Data were coded according to: (1) evidence of leadership behavior, (2) evidence of lack of leadership behavior, and (3) characteristics of the individual in each group who led the subjects out of the mines. This paper discusses the profile of six individual leadership characteristics which emerged from the data.

By M. A. Lucas

The Bureau of Mines has developed a computerized mathematical model to predict the distribution of accessory elements throughout a metallurgical process. The model can be used to determine process conditions that effect better accessory element control consistent with continued high primary metal recovery. The model presented is specific for determining the bismuth distribution in lead smelting but can be adapted to most extractive metallurgical processes. Thermodynamic, kinetic, and process parameters form the base for the model. Its logic and structure are described in detail.

Jan 1, 1983

By A. Sainato, S. J. Kravits, G. L. Finfinger

This Bureau of Mines report describes and compares the procedures, capital investments, and operating costs of rotary and in-hole motor drilling techniques used to drain methane gas from the Pittsburgh Coal- bed in an underground mine located in southwestern Pennsylvania. A timestudy was conducted during the drilling of each of two boreholes, and the data were collated to serve as a base for comparing drilling procedures and operating costs. Findings indicate that drilling with an in-hole motor offers four advantages over rotary drilling; namely, an increase in drilling productivity, fewer worker-hours required, ease of maintaining vertical and horizontal bit trajectory, and less expensive drilling cost per foot of borehole.

Jan 1, 1985

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By K. L. Rubow

"Diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and as found in five underground coal mines- 3 utiliting diesel-powered hallage equipment and two electric-powered equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations. The first technique, using a microbrifke uniform deposit impactor CMOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of .the aerosol is predom1nately submicrometer and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance CCMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results. ,The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral ·dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 um. For the diesel equipped mines, this analysts yielded an average value for the fraction of the fine aerosol attributable to mineral dust of 1 pct. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling."

Jan 1, 1988

By Kevin Connor

Exports of agricultural products, mostly coffee, continued to account for more than 90% of Burundi's foreign exchange revenue. The country's ban on commercial mining was lifted in 1987. Mining of peat for fuel, limestone for agriculture, and clay for insecticides continued as in previous years. At yearend, Burundi's external debt stood at almost $700 million.2 Amoco Burundi, a subsidiary of the Amoco Petroleum Co., drilled two exploration wells in northern Lake Tanganyika in 1987. No oil was found, but preliminary findings were encouraging enough that further seismic surveys and offshore and onshore drilling exploration were planned in 1988. Any oil or gas finds would have substantial impact on the Burundian economy because a major portion of the country's trade deficit was directly attributable to petroleum and gas imports. The Zaire Government agreed in June to let Amoco Burundi explore Zaire's side of Tanganyika using the same equipment and personnel being used in Burundi.

Jan 1, 1989

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By R. Lindsay Mundell

In the first half of 1990, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in August led to the Persian Gulf War in January and February 1991. The subsequent oil shock contributed to a dampening of the U.S. economy, and the U.S. gross national product rose only 0.9 % to $5,463 billion (U.S. billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The U.S. Department of Defense continued to review stockpile goals and upgrade several mineral materials. In addition, the U.S. Bureau of Mines continued to maintain the standby Emergency Minerals Administration. After the Defense Production Act, which authorizes priorities, allocations, and supply expansion, lapsed on October 20, 1990, the Selective Service Act of 1967 became the authority to ensure that orders of the Armed Forces and defense atomic energy programs were given priority treatment.

Jan 1, 1993

By Roberta L. Hudak, Ellsworth R. Spencer, Eric R. Bauer, Adam K. Smith

The National Institute for Occupational Safety and Health (NIOSH) is conducting research with the objective of preventing hearing loss in the mining industry. Longwall mining is one sector that has received considerable attention. Studies involving the monitoring of worker noise exposures, characterizing equipment sound levels and dominant noise sources, evaluating engineering noise controls, analyzing hearing protection device (HPD) effectiveness, and testing of improved sound level monitoring techniques specifically for longwall mining systems, are being conducted. The research efforts revealed that stageloader operators are the most exposed longwall workers, with the discharge end being the noisiest location along the stageloader. In addition, the studies have shown that using stationary dosimeters, coupled with observational data of the cutting cycle and worker habits, has the potential for improved monitoring of the effectiveness of engineering noise controls. To address the ineffective use of soft foam earplugs, a simplified 3-step method was developed for inserting soft foam earplugs. Results indicate a 9 dB greater attenuation after training subjects on the 3-step method. Finally, muff type HPDs are being evaluated for effects of speech intelligibility in noise. The combined results of these studies illustrates that much can and has been done to prevent noise-induced hearing loss (NIHL) in the mining industry, especially with respect to longwall mining workers. This paper presents an overview of ongoing studies, a progress report of results, and the implications for reducing worker noise exposures and preventing NIHL in longwall mining workers.

By A. F. Colombo

Infrared spectroscopy employing attenuated total reflectance (ATR) techniques on thin films of dried gelatinized starch solution was used during Bureau of Mines research to determine the structural and impurity differences in starch products and to correlate these characteristics with the flotation response of a nonmagnetic taconite. All of the starch products evaluated gave spectrograms which were characteristic of the anhydroglucose monomer and its polymerization product. Distinct infrared absorption peaks caused by the protein molecule were observed and were used to classify the starches. Correlation of laboratory flotation of calcium-activated gangue from a Mesabi Range nonmagnetic taconite and infrared spectra produced from gelatinized starches showed that protein impurities and linear chain structure limited the effectiveness of starches as iron mineral depressants. Starch products having spectrograms similar to pure amylopectin were generally good depressants for iron oxides, were effective at about one-half the addition that was required for starches that gave infrared responses similar to pure amylose, and yielded acceptable iron concentrates containing 61.5 percent iron and 6.5 percent silica.

Jan 1, 1969

By Arno C. Fieldner

Forty years have elapsed since the Bureau of Mines was established on July 1, 1910, by Act of Congress. The convocation of this Sixth International Conference of Safety in Mines Research Directors, 24 days after our 40th birthday, seems to be an appropriate time for reviewing our contributions to mine safety research and the problems yet to be solved from the American point of view. Actually research on safety in coal mines was started by the United States Government in the Technologic Branch of the U. S. Geological Survey of the Department of the Interior in 1908, as a result of a succession of disastrous coal mine explosions in which many lives were lost. In 1910 this work was transferred to the newly created Bureau of Mines. 394 lives were lost annually per 100,000 men employed in the coal mines of the United States in the 5-year period ended in 1910, as compared to 203 lives lost annually in the 5-year period ended with 1949. In 1908 no safe, permissible types of explosives and no certified permissible equipment of any kind were used in American coal mines. Black powder was in universal use and open oil or acetylene lights were common in all but mines known to be gassy. Rock dusting was not practiced to limit propagation of explosions, nor was ventilation in many mines adequate, Our safety practice lagged behind that of foreign coal- mining countries and therefore one of the first steps in carrying out the Congressional Authorization of 1908 to investigate the causes of mine explosions was to obtain assistance from the leaders of mine safety research in foreign countries. At the request of Dr. Joseph H. Holmes, director of the Technologic Branch of the Geological Survey, James R. Garfield, Secretary of the Interior, obtained the cooperation of the Governments of England, Belgium and Germany in sending Captain Arthur Desborough, Inspector of Explosives in England, Mr. Victor Watteyne, Inspector-General of Mines in Belgium, and Mr. Carl Meissner, Counselor for Mines in Germany, to visit American mines and make recommendations for increasing safety and efficiency in mining coal in the United States.

Jun 1, 1950

By V. E. Erwin, W. W. Adams

"Production of explosives for industrial use in,the United States during 1934 continued the upward trend begun in 1933 from the low-level output of 1932, and the output in 1934 was only slightly less than in 1931.Reports to the United Stated Bureau of Mines from companies engaged in the manufacture of industrial explosives showed that the quantity of explosives manufactured in the United States and sold during 1934 for use within the various States was 314,767,922 pounds - 23 percent more than in 1931.Production during 1934 included 39,207,845 pounds of permissible explosives 5 206,625,027 pounds of high explosives other than permissibles, and,68,935,050 pounds of black blasting powder of which 37,192,700 pounds were in granular form and 31,742,350 pounds in pellet form. These figures represent an increase over 1933 of 15.6 percent for permissible explosives, 30.9 percent for other high explosive, and 7.4 percent for black powder.Coal-mining operations were the chief consumers of permissible explosives; 99 percent of the total output in 1934 was used, in coal mines. The proportion used by bituminous mines was 59 percent and by anthracite mines 40 percent. Coal mining was likewise the principal consumer of black blasting powder, taking 88 percent of the total sales during 1934; of this proportion, bituminous mines received 78 percent and anthracite mines between 9 and 10 percent. Consumers of high explosives other than permissibles were more varied; the reports showed that 11 percent of the total quantity sold was for coal mining, 22 percent for metal mining, 17 percent for quarrying and nonmetallic-mineral mining, 46 percent for railway and other construction work, and 4 percent for all other purposes."

Oct 1, 1935

By Isaac A. Zlochower

A number of ignition incidents involving mining and farm equipment have illustrated the surprising danger of drilling, cutting, or otherwise penetrating sealed compartments or frames that are filled with metal scrap for ballast. The presence of chemically-reactive metals (or electrochemically-active pairs), such as zinc in galvanized steel, can produce hydrogen from moisture in the steel scrap, and the resulting pressure, due to the internally-generated hydrogen, can produce an easily-ignited gas jet when the sealed component is penetrated.

By Vijia K. Karra

The goal of aggregates producing companies across the United States is to ensure their workers go home safely each day. At the National Institute for Occupational Safety and Health (NIOSH), researchers are pursuing this vision of safety and health through a fact-finding approach for reducing injury illness in various mineral sectors. Surveillance data from Mine Safety and Health Administration (MSHA) has been the source for such analyses. It helps to focus research efforts on key machinery, workers, and their tasks. The second installment of this two-part series follows last month's focus on crushed stone.

By D. E. Shanks

The Bureau of Mines investigated the effects of HCI concentration and solution temperature on the solubility and crystal form of the chlorides of Co, Mn, and Ni when sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increasing HCI concentration in solution caused the chlo-rides of Co, Mn, and Ni to crystallize (salt out) because of the common ion effect. The salting-out crystallization was most effective for NiCI2, which had a solubility of 0.7 pct at 20° C and maximum HCI concentration. COCl2 salted out to a minimum solubility of 9.4 pct at 20° C and 22 pct HCI concentration and increased in solubility at greater HCI concentrations because of the formation of chloride complexes. MnCl2 was intermediate in behavior. The effect of temperature on solubility was greatest for CoCl2 and least for NiCI2, 15 and 7 pct change, respectively, over the temperature range of 20° to 60° C. The salted-out chlorides of cobalt and nickel formed the hexahydrates and those of manganese formed the tetrahydrate in saturated metal chlo-ride solutions at 20° C and low concentrations of HCI. Increasing the temperature or the HCI concentration caused a 108s in waters of hydra-tion. At 60° C, the salted-out crystals of NiCl2 formed the tetrahydrate in HCI concentrations up to 18 pct and the dihydrate at higher concentrations, while cobalt and manganese chlorides formed the dihydrates, even in water.

Jan 1, 1985

By James J. Bryja, Thomas M. Barczak, Dennis R. Dolinar, Joe Bower, Thomas P. Mucha

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial and error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground, reaction behavior based on the support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health (MOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate -- application of alternative roof support systems or to design in- mine trials such that a fair and equitable comparison of different support systems can be made. A case study if the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to conventional wood and concrete cribbing historically used at this particular mine.