Search Documents

By S. F. Ravitz, T. M. Romslo

During 1940 and 1941, the Bureau of Mines examined a large number of silver mines in Arizona for their potential as producers of manganese ores. Although very little manganese ore had been produced from these mines, it was generally known that manganese oxides in appreciable amounts were associated with the silver ore. Following the examinations, the Bureau further investigated some of the ore deposits by diamond drilling and other types of sampling. The results of these investigations, from the viewpoint of manganese, were discouraging. However, the investigations did indicate that appreciable tonnages of manganese-silver ores had been left in some of the mines by earlier operators. Most of these ores were too low-grade for direct shipping as ores of manganese or silver, and their beneficiation by ordinary processes was not economic. Exploitation of the ores appeared to be dependent upon the development of a low-cost milling method, which would yield a marketable manganese product and recover a high percentage of the silver. Later, the Bureau of Mines constructed an experimental mill at Salt Lake City, Utah, for the treatment of manganiferous ores by the dithionate process, designed to recover manganese as a high-grade product. The dithionate residues can be treated by other processes for the recovery of additional values that may be present in the ore. This development focused attention on the manganese-silver ores of Arizona and led to setting up Bureau project No. 370, which is the subject of this report.

Jun 1, 1947

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981

By Wilbert J. Huff

For the past 8 years the technical studies conducted by. the Explo- sives Division of this Bureau have been summarized in a series of annual reports.3 This report deals with activities from July 1, 1942, to June 30; 1943. Specific problems have been in immediate charge of section or unit leaders, to whom credit is given.

Feb 1, 1944

By James J. Olson

The Bureau of Mines recorded both particle accelerations and velocities from one-stick and production blasts at Eagle-Picher Industries' Shullsburg mine, Shullsburg, Wis., to test the effectiveness of square root scaling in grouping underground blast vibrations and to determine the effects of rock type and mine geometry on blast vibrations. Although the charge weights of subsequent delay periods sometimes exceeded the charge weight of the zero-delay period, both acceleration and velocity records showed that the zero-delay portion of the Shullsburg production blasts produced the highest vibration amplitudes. Because of the restricted range of charge weights in the Shullsburg experiments, no statistical determination of an appropriate scaling factor could be made. However, the square root scaled peak particle velocity data from the Shullsburg production blasts grouped well within the approximate band-width of vibration data obtained by the Bureau from quarry blasts in many different rock types. This indicates that scaling by some factor, perhaps the square root or cube root of the charge weight, may be an effective way to group and study vibration data from underground blasts. Further research is needed to determine which scaling factor is best for underground blasting.

Jan 1, 1970

By J. J. Henn

A process is evaluated for recovering metallurgical-grade manganese are from the low-grade manganiferous iron ores of the Cuyuna Range, Minnesota. The process, developed by the Bureau of Mines, employs high-temperature sulfatization of the are to form manganese sulfate and reduction of the are to convert the iron to a magnetic oxide. The roasted ore is water-leached to dissolve the manganese sulfate, which is then separated from the leach residue, is crystallized, and is calcined to produce the manganese product. Iron is recovered from the leach residue by magnetic separation, and is pelletized and calcined to produce byproduct iron ore pellets. The fixed capital cost for a plant yielding a product containing 100 tons of manganese per day is $19.6 million on a mid-1970 basis when the raw are contains 4.84 percent manganese. The estimated operating cost of the plant is $211 per ton of contained manganese. Graphs are included to show the effects of ore cost and varying manganese content of the raw ore on the estimated operating cost.

Jan 1, 1972

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state. Adsorbed gas is stored in the micropore structure and its transport is governed by Fick's law. The free gas occurs in the fracture system and flows according to Darcy's law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds

May 1, 1969

By D. N. Nilsen

The Bureau of Mines is developing a method to recover Ni, Co, and Cu from laterites containing less than 1.2 pct Ni and 0.25 pct Co. The method consists of the following basic unit operations: (1) reduction roasting, (2) leaching, (3) solvent extraction, and (4) electrowinning. The method reflects three Bureau of Mines objectives: (1) recovery of critical minerals that are domestically in short supply from low-grade domestic laterites, (2) lower processing energy requirements, and (3) solution recycling. This report deals with the extraction of cobalt and the preparation of a suitable cobalt electrolyte by solvent extraction from liquor produced by this method. Nickel and copper are coextracted with LIX64N from an ammoniacal ammonium sulfate leach liquor containing about 1.00 g/l Ni, 0.30 g/l Co, 0.03 g/l Cu, and 0.02 g/l Zn. Cobalt (III) in the nickel-copper barren raffinate is reduced to cobalt (II) with cobalt metal. Reduction of cobalt (III) to cobalt (II) greatly aids subsequent extraction. Commercially available XI-51 extracts about 94 pct of the cobalt from the treated raffinate in one stage in a laboratory mixer-settler continuous circuit. Ammonia loaded on the solvent is removed in two washing steps. About 94 pct of the cobalt then is stripped from the XI-51 in one stage with spent cobalt electrolyte containing about 77 g/l Co and 18 g/l sulfuric acid (H2S04), Electrolytes containing less H2S04 also may be used. Preliminary data indicate that coextracted zinc may be removed from pregnant cobalt eletrolyte containing 3 g/l or less H2S04 with di-(2 ethylhexyl) phosphoric acid (D2EHPA).

Jan 1, 1980

By James E. Hill

TECHNOLOGY is best nurtured by a sympathetic climate that is a composite of many factors. Necessity is a highly motivating factor as illustrated by the abnormal surge of technologic development curing wartime. Other factors include appropriate timing, economic pressures, available personnel, and in some instances, legislative action. Problems of recent concern to mining technology have been the quality and quantity of available technical personnel and the possibilities of restrictive legislation. The quality and quantity of technically trained personnel may be inadequate to meet the rapidly increasing complexity of modern technology coupled with the growing demand for qualified personnel. The question of appropriate training was a subject for debate.2 The curriculum and methods of teaching have changed. Questions have been raised on the relationship of scientist and engineer, interdisciplinary versus specialized curriculum, undergraduate versus graduate training, and the place of the smaller schools versus the large university-research complexes that have developed at some universities. Various aspects of the subject of engineering education for the mining industry were discussed at the meeting on Mining and Mineral Engineering Manpower at the Michigan College of Mining and Technology, November 18-19, 1963. Meanwhile, the trend toward interdisciplinary training gathers momentum as illustrated by the establishment of the School of Engineering Science at Johns Hopkins, the Schools of Engineering and Applied Science at Columbia, Princeton, and Yale, the Division of Engineering and Applied Physics at Harvard and, more recently, the School of Engineering Science at Florida State University which cuts across the conventional areas of civil, mechanical, electrical, and chemical engineering.

Jan 1, 1964

By S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By C. H. Elder, Fred N. Kissell, S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By H. E. Powell

The mineral dressing research here reported is part of a continuing program by the Bureau of Mines to develop new or improved concentration processes for oxidized or partly oxidized lead and zinc ores. A sample of low-grade sulfide-oxide, lead-zinc ore from Jasper County, Mo., containing galena, cerussite, pyromorphite, hemimorphite, smithsonite, and sphalerite was concentrated by froth flotation and tabling to a grade of 66 percent lead. Because of the presence of a high content of slime-size values, the overall recovery of lead was limited to 64 percent at this grade. Tests to recover the zinc by froth flotation and by gravity concentration did not give satisfactory results. INTRODUCTION Since its establishment, the Rolla Metallurgy Research Center has con-ducted studies of base metals as a part of its overall program (1, 2, 3, 4, 5,6,7).3/ This research has been, and is, directed to beneficiating complex and submarginal ores, to retreating rejects from commercial installations, and to developing fundamental data.

Jan 1, 1960

By G. V. Sullivan

This report describes an investigation by the Bureau of Mines of flotation techniques for the recovery of chromite from fine-grained disseminated ores. Reported work on the concentration of chromiferous materials shows that flotation has been applied almost exclusively to slime-free pulps. Therefore, chromium recoveries that could be obtained by flotation were related to the amount of slime rejected. However, results of recent studies by the Bureau of Mines showed that des liming is not a requisite to selective concentration of chromite. Laboratory-scale tests on seven ore types from the more important chromium-bearing areas of the Pacific Northwest showed flotation to be technically feasible for treatment of all but one of the samples. Concentrate grades were affected more by the composition of the chromite mineral than by the grade or character of the ore. Test results from three of the samples showed that, without prior desliming of the pulp, 78 to 91 percent of the chromium could be recovered in concentrates of 90 percent or more chromite; two samples responded to similar treatment, resulting in concentrates of more than 80 percent chromite with recoveries of 85 and 89 percent chromium. One sample of mill products, subjected to severe weathering, required removal of the primary slime to obtain a concentrate of 65 percent chromite with only 75 percent chromium recovery.

Jan 1, 1960

By Clarence Hall, Charles E. Munroe

In accidents resulting from the use of explosives in metal mines and quarries in the United States more than 130 men were killed and 250 seriously injured during the calendar year 1913. More- over, an unknown number of miners suffered from the effects of breathing the harmful fumes and gases given off by the burning or the incomplete explosion of some explosive. Consequently, the Fed- eral Bureau of Mines, which is endeavoring to increase safety in mines and to abolish conditions that tend to impair the health of miners, is studying the kinds of explosives used in mining and the conditions under which these explosives can be used with least danger to the miner. Information about the different explosives used in coal mining and the precautions to be taken in using those explosives has been printed in Bulletin 17 and other bureau reports, the names of which may be found at the end of this bulletin. The bureau has not been able to give much attention to explosives used in metal mines and quarries, but has published some information about these explosives in Bulletin 48, "The Selection of Explosives Used in Engineering and Mining Operations"; Technical Paper 17, "The Effect of Stemming on the Efficiency of Explosives"; and Miners' Circular 19, "The Prevention of Accidents from Explosives in Metal Mining." This bulletin aims to give the metal miner and the quarryman information similar to that given the coal miner in Bulletin 17. In- flammable gas or dust is seldom, if ever, found in quarries or metal mines, and the danger from using explosives there is less than in coal mines; but, as the figures show, the number of men killed and injured yearly in accidents caused by explosives proves the need of both miners and mine officials striving to see that none but proper explosives are used and that these are used properly.

Jan 1, 1915

By Soule&apos, John H.

Although known since 1902, the Capitan iron deposits have not been tined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-4, visited the property; as a result, preliminary sampling of the property was done in 1943.2/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944. Equipment available at that time was limited in the depths that could be reached; and as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.

Jan 1, 1949

Work on this program was supervised by R. C. Streeter, Project Scientist, R. K. Young, Principal Investigator, and R. A Glenn, Project Director Technicians involved in the conduct of the experimental work were J R. Allender, D. R. Wolber, G. L Maclay, and A. C Rupert The assistance of Project Scientists C. T. Ford in the electrokinetic studies, and R. R. Care in the spectrographic analyses, is also acknowl- edged. The valued advice and guidance during the course of this program from R. D Hill, EPA Project Officer, and Dr. D R. Maneval, Director of Planning and Coal Research for the Department of Environmental Resources, Commonwealth of Pennsylvania, is sincerely appreciated.

Jan 1, 1971

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By J. H. Soulé

The Copper King copper-gold-silver deposit was discovered about 1880. Various individuals and companies have been interested in the deposit and considerable work has been done, although production, if any, has been small. The deposit is located in the western part of Laramie County, Wyo., and is favorably situated with respect to rail and truck transportation and high-tension power facilities. Mild summers and cold winters characterize the climate. Precipitation averages between 16 and 17 inches annually, with considerable snowfall in the winter. Permanent streams are small and most available water in being stored for use by Cheyenne, Wyo. Range grasses comprise the bulk of the vegetation, with small trees and shrubs common in the most rugged areas.

Jan 1, 1955

By A. W. Ambrose

"A need exists for men in oil-field production work who correspond to the mining engineer of a large mining property. Some oil companies prefer to call such an employee a resident geologist, resident engineer, or a petroleum technologist. He should perhaps be more correctly termed a petroleum production engineer. The duty of such a man is to apply his scientific and geologic training practically to oil-field development work.He should be, by education, a mining, civil, or mechanical engineer, with a knowledge of geology and chemistry. Upon completion of his education, such a man should spend several years in the oil-fields. There are two means of gaining proper experience. The first method is to work for an oil company in making a detailed study of each well, collecting data on the history and production, followed by a preparation of good records, from which well logs can be prepared. From the well logs, the geologic cross-sections, peg-models, and structure contour maps can be made. These allow a comparable, detailed study of each well, which is necessary to solve many of the problems. Along with this the engineer should visit drilling wells daily for collection of samples of formations and for a proper study of how they drill. He should form friendly relations with the drillers and production foremen. The second method of gaining proper experience is to start work as a roustabout, pumper, or on the pipe¬line gang, finally working up to a tool-dresser. After three or four years of such work, the engineer may be classed as a petroleum production engineer."

Jan 1, 1920

By Zachary J. Fink

A continuous-monitoring system has been developed for analyses of mine gas concentrations associated with spontaneous combustion, mine fires, and explosive and toxic levels. The analysis center, which is linked to sample locations by polyethylene tubes in bundles, has been successfully field tested by the Federal Bureau of Mines for analyzing carbon monoxide and oxygen; a computational scheme has been developed to process the data at the site. This report contains information on the design, purchase, installation, and maintenance of the tube-bundle system. A brief comparison of the tube-bundle system with the underground-analysis system and plans for future research are also included.

Jan 1, 1975