Search Documents

By Wesley G. Holtz

A project to demonstrate the feasibility of retorting oil shale by the Paraho vertical retort process was carried out at Anvil Points, Colorado during 1974 to 1976. As a part of the demonstration project, laboratory and field tests were performed to determine the physical and chemical properties of the retorted shale for use in the development of eventual full-scale disposal plans. The material which exits from the Paraho retort is classified as a non-plastic silty gravel by the Unified Soil Classification System. The particles have an apparent specific gravity averaging near 2.60 and a mass specific gravity averaging near 2.00. The material can be compacted by normal laboratory and field construction methods to about 90 to 100 pounds per cubic foot dry density depending upon the degree of compactive effort applied. The addition of moisture does not improve compactibility appreciably. When high compactive effort is applied the retorted shale is classed as impervious to water flow. The compacted retorted shale exhibits shear strengths in the same order as those observed for silty gravel soils. If the compacted material is cured (long tune simulation testing) prior to strength testing considerable strength gain can be obtained from cementing action. The amount of cementing developed is dependent upon heat treatment and other operating modes of the retort.

Jan 1, 1976

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 30 jurisdictions of the Western Hemisphere. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1970

By W. R. Hardwick

This paper describes mining methods and practices of the Chino Mines Division, Kennecott Copper Corp., Grant County, N. Mex. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A similar program was conducted from 1928 to 1939, which helped to improve the efficiency of mining operations. The primary purpose of the program is to promote development and conservation of our mineral resources by disseminating technologic information on methods, practices, and related features in mining mineral deposits. It is expected that the program will: (1) Promote efficiency in operating mines; (2) assist operators and engineers in evaluating and developing new mineral deposits; (3) provide data for engineering curriculums in mining schools; and (4) furnish performance and cost data for revising engineering handbooks and for inclusion in engineering textbooks.

Jan 1, 1958

By E. D. Gardner

This paper is the third of a series of three on placer mining in the western United States. The first paper4 discusses the history of placer mining in the Western States and the production of placer gold, geology of placer deposits, location of placer claims on public lands, sampling and estimation of gold placers, and classification of placer-mining methods, together with hand-shoveling and ground-sluicing. The second papers deals with hydraulicking, sluice boxes and riffles, recovery of gold and platinum from placer concentrates, treatment of amalgam, and marketing of placer gold. The discussion of sluice boxes and subsequent subjects in the second paper applies to all forms of placer mining. The present paper treats of dredging and other forms of mechanical handling of placer gravels, and drift mining.

Jan 1, 1934

By Robert D. Ewing

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, and axisymmetric and plane joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1976

The Federal Coal Mine Health and Safety Act of 1969 requires that each operator of a coal mine shall take accurate samples of the amount of respirable dust in the mine atmosphere to which each miner is exposed, a measure designed to prevent the development of coal workers' pneumoconiosis. This textbook manual is used in the training of personnel to operate respirable dust sampling devices and to conduct sampling programs. It contains the portions of the act applicable to respirable dust standards, the procedures to be followed to insure compliance with Federal regulations, and descriptions of sampling devices.

Jan 1, 1971

By Edward W. Parsons

Conventional rock-bolt anchors often fail when installed in weak formations. The purpose of this work was to develop an anchor that would utilize an explosive charge to secure anchorage in any type of rock. Laboratory work to develop a rock-bolt anchored by explosive forming was initiated using rock-bolt models which had a drilled explosive chamber and were composed of various metals. This was followed by the use of several types of seamless tubing which were expanded with a water-coupled explosive capsule. By attaching a length of solid bolt to the anchor tube, a prototype explosive-anchored rock bolt was made. More than 150 laboratory models were expanded during this phase of development, During two field tests in underground mines (A and B) and one in an open- cut mine (C), 87 explosive-anchored bolts, 9 slot-and-wedge bolts, 2 bolts anchored with expanding grout, and 28 expansion-shell bolts consisting of three types of shells were installed and subjected to pull tests. The field tests were run to determine the effects of variables such as the amount and placement of the explosive charge, design changes in the bolt, and the effect on anchorage of different pull-test techniques. The field tests revealed the following: Mine A. The explosive-anchored rock bolt was feasible, but changes were necessary in bolt materials and in some details of bolt design. Mine B. The design and materials of the bolt gave excellent results in hard fractured rock, but no information was obtained concerning variations in the dimensions of the anchor unit or in the explosive charge. Nine C. Varying the explosive charge to produce a beaded surface on the bolt tube and tightening of the anchored bolt before pull-testing were found to increase significantly the anchorage obtained in soft ground.

Jan 1, 1963

By W. I. Nissen

As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pet S02. In this regenerable flue gas desulfurization (FGD) process, S02 is absorbed from cleaned and cooled industrial flue gas with a citric acid-sodium citrate solution. The absorbed S02 is subsequently reacted with H2S to precipitate marketable elemental sulfur and regenerate the solution for recycle. Laboratory investigations of process parameters provided information for designing larger scale continuous operations. Information gathered from operation of two pilot plants, one at a copper smelter and one at a lead smelter, confirmed the laboratory results. Data were obtained for design and construction of a commercial-sized demonstration plant at the George F. Weaton Power Station, Monaca, PA. A preliminary operation of the plant was demonstrated, under a cost-sharing Bureau-industry contract. This bulletin describes the citrate process and gives results of the laboratory, pilot plant, and demonstration plant studies, as well as corrosion investigations.

Jan 1, 1985

By Frank Cook

In this two-year study, an evaluation of mining and reclamation practices at 159 randomly sampled surface coal mines in the United States was conducted. It is concluded that reclamation practices in most of the 22 coal-producing states were adequate during 1975, but that improvement in reclamation performance was desirable in the acid area of the central U. S. and in mountainous southwestern Virginia. Productivity improvements should result from research to determine efficient or optimal operating procedures for dragline stripping of single and multiple seams, surface mining of lignite, multicut and multiseam haulback mining on steep slopes, mountaintop removal, and surface mining in swampy or deeply glaciated areas. Specific candidate research projects are discussed in this report.

Jan 1, 1976

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By M. J. Ackerman

This study was undertaken to make a comparison between the cost of mining coal under roof bolt and under conventional timber methods of roof support. Studies were made at 14 mines in Pennsylvania, eastern Ohio, and northern and southern West Virginia. At each mine data were obtained for sections of the mine where the physical conditions, mining equipment, and mining systems were similar. Coal, recognized as one of the basic industrial fuels, is very competitive with other fuels, and management, in order to protect and enlarge its market, must be continually alert to find more efficient methods of production. Continuous production of coal is desired by all operators but never obtained. In mechanized mining the performance and production vary with operating time, which can be interrupted by many variable factors, such as condition of the roof, method of roof support, condition of equipment, water, ventilation, power, transportation, efficiency of operating crew, and supervision.

Jan 1, 1961

By D. Harrington

For several years, or from about 1932 to 1935, inclusive, the coal industry of the United States had an excellent record as to coal-mine explosions. In 1937 and in 1938 to date there has been a definite increase in the number of explosions attended by considerable loss of life and property damage. In most of these explosions one important underlying and contributing cause has been lack of sufficient (or at least efficient) ventilation to properly dilute and remove explosive gas from the mine. This increase in explosions indicates that. the lesson taught through bitter experience, many times in the not far-distant past, of the need for good ventilation is frequently being overlooked, partly because the relatively good experience of the industry in the past several years has made many mining people forgetful. Moreover mining practices are rapidly changing, and in some instances the changes are being made with little if any regard for safety. It appears, therefore, that a review of some ventilation principles and practices should be of value in preventing further disasters; this paper has been prepared with that object in mind. In coal mining the need for thorough ventilation of all underground working places is recognized by both mining practice and law; such ventilation is generally obtained by the use of fans that circulate a quantity of air much in excess of the quantity of coal produced, by weight as well as by volume. For example, in a relatively small mine producing 1,000 tons of coal per day and circulating 100,000 cubic feet of air, which is by no means abnormal, 2,000,000 pounds of coal and approximately 10,900,000 pounds of air would be moved out of the mine every 24 hours. Because of the need for adequate dilution and removal of methane issuing or likely to issue from mine strata and for removal of the carbon dioxide formed by coal and timber oxidation up-to-date coal mines usually provide an air volume which if adequately coursed not only removes these gases but also the gaseous products of the detonation of explosives (which may include carbon monoxide, hydrogen sulphide, nitrogen oxides, carbon dioxide, and nitrogen) and the carbon

Jan 1, 1938

By Robert J. Timko

In early June 1986, an underground fire of unknown origin erupted in one of several entries of a coal mine located in southwestern Colorado. For a time, mine personnel aggressively fought the fire. However, control of the fire was later lost. To prevent further damage and reduce the possibility of an explosion, all portals and shafts to the mine were sealed. The mine operator requested the U.S. Bureau of Mines' assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals, as well as down boreholes drilled after the fire. This report recounts activities within the first 2 years of the mine being sealed. It includes a description of gases analyzed and mine atmosphere status equations generated from the analyzed gases. The gases were analyzed by chromatography and included standard atmospheric gases as well as higher hydrocarbons that are found in postfire atmospheres. Nine equations were used to evaluate what was occurring within the sealed mine. Following a description of the rationale behind each equation, the 2-year trend is briefly analyzed.

Jan 1, 2010

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By H. A. Dierks, H. B. Link

The purpose of this investigation was to develop a practical feeder apparatus to introduce comparatively large pieces of coal and similar material into a pipeline under pressure in connection with the vertical hydraulic transportation of solids , termed " hydraulic hoisting . " This method of hoisting the precrushed run - of - mine product of an underground mine has been given unusually wide attention abroad and could be of considerable significance to the U.S. mining industry in its search for operating improvements and cost reduction . A lock-hopper assembly was developed after a series of sinking velocity tests were made by dropping anthracite in a column of water . The system functioned reliably as an automatically operated feeder apparatus .

Jan 1, 1964

By E. P. Barret

Differences in the reducibility of iron oxide materials have been recognized for a long time. Limonites are deoxidized more readily than hematites, and unaltered magnetites are the most difficult to deoxidize. Sinters are found between hematites and magnetites and vary considerably in reducibility, depending on the sintering practice followed and on the degree of fusion of the product. The increased activity in the beneficiation of taconite recently has made available a new blast-furnace raw material, namely, iron oxide pellets made from magnetic taconite concentrate. Many of the data in this paper apply to these pellets, or glomerules, as they were called when this method of agglomerating iron ores was first considered. To clarify the terms applied to iron oxide materials in this paper, the following definitions are given. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron oxide materials. Sinter is the product from a Dwight-Lloyd or Greenawalt sintering machine. Pellets are formed by balling fine, moist oxide in a rotating drum at room temperature, followed by heating in a shaft furnace to a temperature below that of incipient fusion to develop a permanent bond. Nodules are formed by heating the iron oxide material to incipient fusion in a rotary kiln. Briquets are formed in a mold under pressure, with or without the addition of a binder, and burned to develop a permanent bond.

Jan 1, 1949

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956