Search Documents

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By I. L. Nichols, K. C. Dean, P. H. Johnson

Hydrochloric acid , sulfuric acid , and chloridizing roast- water leaching methods for dissolution of cesium and rubidium from Maine , Canada , and Southern Rhodesia pollucite ores and their flotation products were investigated by small- scale tests . Optimum conditions were determined to be ( 1 ) for hydrochloric acid leaching , use 12.7 equivalents of 8.8 normal acid per equivalent of cesium in the sample and leach for 6 hours at 100 ° C ; ( 2 ) for sulfuric acid leaching , use 12.7 equivalents of 14.4 normal acid and leach for 2 hours at 120° C ; and (3 ) for chloridizing roast - water leaching , roast minus 200 - mesh ore, limestone , and calcium chloride in a ratio of 2 : 4 : 1 , respectively , for 1 hour at 900 ° C , and leach the calcine for 1 hour at 80 ° C with enough water to give 35 pct solids . Extractions of cesium from ores and flotation products containing over 20 pct cesium were in excess of 97 , 93 , and 96 pct for the hydrochloric acid , sulfuric acid , and chloridizing roast - water leach processes , respectively .

Jan 1, 1964

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By D. A. Reynolds

THIS PAPER gives results of an investigation of the composition and carbonizing properties of coals from the Beckley bed, Caretta No. 5 mine, Susanna, McDowell County, and Glen Rogers No. 2 mine, Glen Rogers, Wyoming County, W. Va. The investigation included BM-AGA carbonization tests at. 800° and 900° C. and various chemical and physical tests designed to evaluate agglutinating, plastic, and expanding properties of coal. Both coals were of low-volatile bituminous rank, and each was blended with 70 and 80 percent high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa. The Beckley bed was 39 to 58 inches thick at three points in the Caretta No. 5 mine, and the coal was 39 to 49 inches thick. The carbonizing sample contained 83.0 percent fixed carbon on the dry, mineral-matter-free basis. It contained 3.1 percent moisture, 15.8 percent volatile matter, 72.4 percent fixed carbon, 0.7 percent sulfur, and 8.7 percent ash, as carbonized. The ash softened at 2,680° F. The free-swelling index was 7;i, and the agglutinating value was 7.7. This sample fused weakly in the Gieseler plastometer; its blends with 70 and 80 percent Pittsburgh coal attained maximum fluidities of 830 and 600 dial divisions per minute, respectively. The single coal yielded 83.0 percent coke at 900° C. Yields of other carbonization products per ton of coal at 900° C. were: Gas, 9,950 cubic feet; tar, 3.5 gallons; light oil, 1.36 gallons; and ammonium sulfate, 16.3 pounds. Blending with Pittsburgh coal lowered the yield of coke and raised the yields of other products significantly. Caretta coal yielded strong, blocky coke at 900° C., 89 percent of which was plus-2-inch size. Strength indexes of 900° C. coke from 30:70 blends of Caretta No. 5 and Pittsburgh and of Pocahontas No. 3 and Pittsburgh coals were, respectively: 2-inch shatter, 68 and 53; 1%-inch shatter, 90 and 85; 1-inch tumbler, 50 and 53; and %-inch tumbler, 62 and 65. The specific gravity of the 900° C. gas from Caretta No. 5 coal was 0.272, and the heating values were 491 B. t. u. per cubic foot and 2,440 B. t. u. per pound of coal. The blends yielded much richer gas. Yields of tar acids and bases (0.09 and 0.04 gallon per ton, respectively) were within the normal ranges for low-volatile coals. Caretta No. 5 coal expanded 7.5 percent in the sole-heated oven at a charge density of 55.5 pounds per cubic foot. The blends containing 70 and 80 percent Pittsburgh coal contracted 4.8 and 7.5 percent, respectively.

Jan 1, 1953

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Clay, Gilmer, and Lewis Counties, W. Va. In 1966, almost 1.3 million tons of coal was mined in these counties, of which more than one-half was from the Pittsburgh coalbed. Washability analyses were made of 16 coalbed samples. Of these, only 11 samples could be upgraded to metallurgical quality. For steam or power generation five of the coals were of low sulfur content as received. The remaining samples were generally of medium sulfur content even after upgrading.

Jan 1, 1969

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992

By BUREAU OF MINES

In 1948 the United States became a net importer of oil. Coupled with an unpre- cedented domestic production of 5,900,000 barrels daily, imports approximating 500,000 barrels made available a total supply of 6,400,000 barrels a day. Thus, by herculean effort, the oil industry was able to meet an extraordinary demand at home and, in addition, to ship abroad almost 400,00 barrels daily of petroleum and products. The country's oil position now differs greatly from that prevailing at the be- ginning of World War II. Then, actual oil production averaged about 4 million bar- rels a day, and productive capacity probably was greater than 5 million barrels a day. As the demand of the military and industrial machine grew with the rising tempo of the drive toward victory, the United States not only met its own needs but pro- duced about two-thirds of the total oil requirements of the Allied Nations, excluding Russia. As a people, we can be deeply grateful that the Nation's petroleum resources were adequate and sufficiently developed to support such a tremendous effort. Even in those critical hours when immediate needs were the paramount issues, a prudent Congress paused to contemplate the importance of an assured long-term supply of liquid fuels. From these deliberations came the Synthetic Liquid Fuels Act of 1944, which authorized research and development work on new sources of oil coal, oil shale, and agricultural and forestry products. ce World War II, a civilian demand for 6 million barrels of petroleum prod- ucts has become the order of the day every day. By drilling as many as 39,000 new wells a year, the production rate has been increased enough to meet domestic require- ments by a bare margin. Some imports were necessary, however, to fill both domestic and foreign demands, and these doubtless will increase. Is this policy of exploration within the United States and the development of oil in foreign countries adequate insurance for the fulfillment of our future national needs? This question has two aspects one purely civilian and economic in character and the other significant from the standpoint of our national defense. There are now approximately 4,000 producing oil fields in this country. At first thought, it would appear that production could decline in a considerable number of these fields without materially affecting the over-all daily output. However, 48 percent of the oil comes from only 111 major fields which contain 50 percent of the total proved domestic reserves. It is apparent, then, that the flow from large fields - having proved reserves of 100 million barrels or more each must be sustained if daily production is to be kept at the present levels. Essentially, this means that new major fields must be discovered about as rapidly or perhaps more rapidly than the older ones lose productive capacity. From 1940 through 1947, only eight major fields with estimated reserves of more than 100 million barrels each, were discovered and proved - an average of one such field a year. The total estimated reserve of these eight fields was less than 1 year's supply at the present rate of use. As drilling continues, some existing fields ultimately will prove reserves larger than those now known. Without a pronounced increase in the num- ber of major discoveries, however, the prospects for increasing our present productive level are not encouraging. Any gap that appears between domestic productive capacity and demand could be filled with supplies from proved oil resources abroad. Assuming cheap pipe-line and tanker transportation to the United States, freedom from exorbitant taxes and charges

Jan 1, 1949

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite.

Jan 1, 1916

By E. J. (Kirk) Conway

Thirty-five years ago underground coal mining equipment consisted of simple but rugged machines powered by electric motors and hydraulics. The machines were maintained by maintenance personnel armed with a basic knowledge of hydraulics, electricity, and mechanical design. Over the years the the machine has been transformed into powerful complex mining systems. The maintenance burden has also increased. During this period significant advances have been made in maintainability engineering and system design techniques. Many of these innovations and techniques are applicable to the design of underground mining equipment. The objectives of this project were to; (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess the impact of equipment design for maintenance on productivity and safety, and (3) develop a maintainability design guideline to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. Interviews were also conducted with mine management, safety, and maintenance personnel to identify machine specific design advantages and problems. Visits were also made to six original equipment manufacturers to discuss the design of their equipment for maintenance. Volume I presents an overview of the protocol used and a summary of the findings. Volume II includes the maintainability design guide for underground mobile mining equipment.

Jan 1, 1989

Research workers From the Bureau of Mines and industry met with other government and industry representatives in Pittsburgh, Pa., on January 22, 1975, to discuss the results of research under the Bureau of Mines Noise Control Program. The program, aimed at reducing noise in mines, is functionally divided into three major areas: Instrumentation, personal protection, and noise abatement. This proceedings contains the opening remarks to the seminar and seven technical presentations based on various aspects of noise abatement and control.

Jan 1, 1975

By Arden D. Fugate

This work was conducted to determine a feasible process for converting siliceous fluoride offgases to a commercially usable product. The offgases were generated by pyrohydrolytic defluorination of low-grade fluorspar in a gas-fired rotary kiln, and fluorine was collected as a hydrofluoric-fluosilicic acid. A silicon-free fluoride solution for further processing was then produced by neutralizing the acidic scrubber solution with anhydrous ammonia, silicon being separated as orthosilicic acid. Ninety to ninety-nine percent of the fluorine originally present remained in solution as ammonium fluoride. Silicon was also separated from synthetic fluosilicic acids, having F-to-Si weight ratios ranging from 3.50 to 14.3. The solutions below a ratio of 4.06, the F-to-Si ratio of H2SiF6, containing dissolved silicon were desiliconized as completely as those containing less than the stoichiometric quantity of silicon. An electrolytic-grade cryolite was recovered from the ammonium fluoride solution by reacting with either sodium aluminate or alumina trihydrate and sodium hydroxide. A product containing 97 to 100 percent of the fluorine, represented by Na3A1F6, was recovered, and 94 to 99 percent of the theoretical yield was realized.

Jan 1, 1963

By Edward F. Courtney

Loss of life, loss of sight, crippling injuries, and property damage nearly always result from accidents involving explosives. The severity of such accidents has prompted lawmaking bodies to pass laws concerning the transportation, handling, and use of explosives; manufacturers of explosives publish manuals &apos;describing explosives and practical methods of handling then; and mining companies and others who use large quantities of explosives publish rules based on actual experience for the guidance of their employees. Careless storage of explosives by thoughtless or incompetent persons, particularly if they are left where children or saboteurs have access &apos;to them, has led to many serious accidents. Many contractors and mining operators who use explosives are extremely careless about storing them. It is the purpose of this paper to discuss the explosive-handling practices of a large western mining company, which are considered better than most.

Jan 1, 1946

By L. H. Banning

In the fall of 1953 the Philippine Bureau of Mines, under a Foreign Operations Administration Technical Assistance (FOA-TA) program, began a systematic investigation of the nickel content of the well-known Surigao laterite areas, on the island of Nonoc northeast of Mindanao, to determine the occurrence, distribution, and grade of nickel contained in the laterite and in the subjacent serpentine. At the same time, a technical review of the possibility of producing commercial ferronickel from the nickeliferous materials in the Philippine Islands was made, and a smelting process was suggested. The proposed process would be similar to that developed by the Federal Bureau of Mines for the reduction of the nickeliferous serpentine occurring in the Nickel Mountain ?deposit at Riddle, Oreg. The potential avail-ability of electric power from the Maria Cristina facilities at 3 mils per kw.-hr. would enhance the economic possibility of this program. Development of an economically feasible process for recovering nickel from the nickeliferous serpentines and laterites should lead to the establishment of a new industry in the Philippines, to the development of a source of nickel in the Far East, of which at present there is none, and to partial solution of the problem of supplying the free world with nickel. Enough preliminary reconnaissance had been completed by early 1954 to permit sampling of the deposit for metallurgical investigations. The FOA then requested the Federal Bureau of Mines Northwest Electrodevelopment Laboratory, Albany, Oreg., to conduct preliminary electric smelting studies on nickeliferous serpentine and laterite samples.

Jan 1, 1955

By P. C. Good

To meet a growing need for thorium metal of high purity and amenability to fabrication, the Bureau of Mines devised a method for preparing thorium metal by the reduction of thorium tetrachloride. Thorium tetrachloride was prepared by chlorinating calcined thorium oxalate with carbon tetrachloride. The crude thorium tetrachloride, containing oxygen-bearing compounds, was purified by a double vacuum distillation at 800 to 900° C., and thorium metal was made in the form of a dense sponge by the reaction of metallic sodium or magnesium with thorium tetrachloride at 800° C. Vacuum arc melting was used to consolidate the sponge metal to ingot form for evaluation of its physical and chemical properties.

Jan 1, 1960