Search Documents

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

By W. E. Robinson

Samples of raw oil shale and kerogen concentrates were oxidized by alkaline potassium permanganate, air, nitric acid, oxygen, and ozone to obtain information about the chemical structure of organic kerogen in oil shale. In one test, oil shale and oil-shale products were oxidized exhaustively with alkaline potassium permanganate, and the distribution of the organic carbon in the final oxidation products was determined. Comparing results of this oxidation with those obtained from other carbonaceous materials and known compounds gave information about the structure of kerogen. Alkaline potassium permanganate oxidation also was used partly to degrade kerogen into soluble products for characterization purposes. Structures present in these degradation products were indicative of type structures originally present in the kerogen. Nitric acid, oxygen, and ozone were used also for partly degrading kerogen to soluble oxidation products. Carbon-balance oxidation tests using alkaline potassium permanganate showed that Colorado oil-shale kerogen differs from many other carbonaceous materials such as coal and kerogens from other areas. Composition of the degradation products indicated that Colorado oil-shale kerogen is predominantly cycloparaffinic and saturated heterocyclic structures with some long-chain paraffinic and aromatic structures present. The ring systems may be connected through short carbon chains or bridges containing oxygen, nitrogen, and sulfur.

Jan 1, 1963

By R. F. Stewart

A key step in changing coals to fluid fuels and chemicals is the conversion of coal to synthesis gas by gasification with steam and oxygen. As oxygen represents one of the largest single expenses in gasification, its cost is a vital factor in the economy of the process. At present, the most economical method for producing tonnage oxygen is by the conventional rectification of liquefied air. Several alternate methods have been proposed for producing oxygen from air: (1) methods based on physical or chemical sorption of oxygen from air by liquids or solids or (2) the oxidation of certain inorganic com-pounds to higher oxides unstable at higher temperature levels. Economic limitations are discussed by which these methods may be evaluated. Chelated metals of the salcomine type are promising chemical sorbents of oxygen from air. This report covers a study of the reversible sorption of oxygen by salcomine and other chelates. The presence of water in the salcomine structure was verified; it is the loss of this water that causes slow deterioration of salcomine during cycling.

Jan 1, 1959

By Martin A. Elliott

The Bureau of Mines began its investigation of the use of Diesel engines underground to provide technical information necessary to assist this development in the United States. It was considered desirable to furnish such assistance because successful European developments/ in this. field had indicated that Diesel mine locomotives might be safer than electric trolley locomotives. The Bureau has recognized for some time the importance of eliminating the hazards associated with underground haulage systems using bare trolley wires. For example, each year 30 to 40 fatalities occur as a result of electrocution by contact with bare trolley wires. In 1943 and 1944, 101 men were killed and extensive property damage occurred as a result of mine fires started by falls of roof grounding the bare trolley wires.

Jan 1, 1948

By Wilford S. Wright, Harold E. Heide, Robert L. Thorne, Neal M. Muir, Aner W. Erickson, Bruce I. Thomas

A program of investigation of strategic and critical minerals began in 1940 to examine and develop tungsten occurrences in the western United States and Alaska. During the years in which the nation was at war, this work was given special impetus to stimulate domestic production. This report is a compilation of results of the tungsten investigations in Alaska supplemented by certain data made available by the Territorial Department of Mines and is designed to include in its scope descriptions of all known tungsten occurrences in the Territory. Two areas in Alaska warranted special investigation - one at Gilmore Dome, 16 miles northeast of Fairbanks, and the other in the Hyder District, at the head of Portland Canal. Three tungsten properties - the Stepovich, Colbert, and Yellow Pup - are at Gilmore Dome. The Stepovich property, referred to sometimes as the Cleary Hill tungsten deposit, was worked by the Cleary Hill Mines Co. from April 1942 until May 1944 and was first examined by Robert S. Sanford and Norman Ebbley, Jr., engineers of the Bureau of Mines, in September 1942. The Cleary Hill Mines Co. by that time had explored an 800-foot strike length of the ore zone with 10 bulldozer trenches and was sinking an inclined shaft on ore in the central portion of the explored zone. In January 1943, the senior author, in company with Ebbley and Harry C. Doheny, supervising engineer of R.F.C., examined the property. Preliminary work by the Bureau of Mines began in May 1945, but actual exploration did not commence until late in June and continued until the end of October 1943. The deposit was examined by John B. Mortie, Jr., and William C. Overstreet, of the Federal Geological Survey, in 1942, and this study was continued in 1943 by Frank Byors, who also assisted the Bureau’s engineers on geologic problems. A magnetometer survey of this area was undertaken in 1942 by Henry Joosting and Eskil Anderson, engineers of the Territorial Department of Mines, and was completed with Bureau of Mines assistance in 1943. During 1943 the Bureau completed exploratory projects on the Cleary Hill mine and adjacent Colbert prospect. The field work on the Colbert property was begun early in July 1945 and continued intermittently until the end of October 1943, when it was recessed because of subzero weather. During September 1944, the Bureau of Mines established (by means of a few surface trenches) continuity between the Colbert mineralized zone, high on the dome, and the Yellow Pup vein, the lowest known tungsten mineralization in the area. It is generally recognized that any extensive program to develop the area as a whole logically would be carried out from the lower horizon.

Jun 1, 1948

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By R. Farrar

The survey work on protective canopy design was conducted in a 2-month period commencing November 15, 1973. The reported re¬sults under this contract are intended to provide guidance to coal mine operators in complying with federal regulations pertaining to incorporation of protective canopies on underground coal mine electric face equipment. All coal mine electric face equipment manufacturers and 11 coal mines were visited in the course of conducting this survey. Canopy designs currently being manufactured and those now being used underground were examined and discussed with manufacturers, mine operators, machine operators, and safety committeemen. The general objective was to find out what kind of canopies are now being made and used underground, what the operational problems are, and what can be done to secure improvements. Specifically, the survey scope was as follows: a. Survey all electric face equipment manufacturers. b. Survey 10 coal mines (seam height 60 inches and greater). c. Identify current production canopy configurations and minimum mine entry dimensions for each model and type of electric face equipment. d. Assess in-mine operation of canopies developed by manufacturers and/or coal companies. e. Specify optimal canopy configuration and minimum mine entry dimensions for each type and model of electric face equipment.

Jan 1, 1974

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By J. D. Marchant

In the spring of 1953 a series of heats were made using a 3-phase, size ST, Pittsburgh Lectromelt arc furnace to develop a method suitable for melting, refining, and granulating cobalt powder produced by the Calera Mining Co., at Garfield, Utah. According to specifications stipulated by General Service Administration, the granules had to pass a 2-inch screen and be retained on a 6-mesh screen, be low in phosphorus and sulfur, and contain a minimum of 98.7 percent cobalt plus nickel. Various combinations of water temperature, water jets, and rate of pouring were tried early in the campaign to produce desirable granules. It soon became evident that a properly refined and deoxidized molten bath was the major requirement for a satisfactory product. The physical characteristics of the granules were improved also if, just before pouring, the surface of the molten metal bath was pre-pared by a method involving the use of silica flux. The Bureau processed 107,750 pounds of cobalt powder. A total of 104,810 pounds of cobalt granules meeting General Service Administration specifications was returned to the producer. The refining slag, which was also returned to the company, contained 1,781 pounds of metal.

Jan 1, 1955

By Steven E. Mischler

The exposure of mine workers to diesel particulate matter (DPM) and gases is an issue of great concern to the underground mining community in the United States. Approximately 30,000 underground miners are potentially exposed to high concentrations of DPM. In January of 2001, the U.S. Mine Safety and Health Administration (MSHA) promulgated rules setting compliance standards for both underground coal and metal / nonmetal mine workers. As industry works to achieve compliance with these standards, mine operators are looking for feasible methods for reducing DPM concentrations in their mines. In addition, the industry needs methods to accurately measure DPM to ensure that the control strategies they adopt are working successfully. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to evaluate control technologies and monitoring instrumentation that can be used to reduce the diesel particulate matter (DPM) exposure of mine workers. An overview of the strategies being utilized in underground US mines to reduce DPM concentrations will be presented. Also, updates on the development of diesel monitoring instruments such as the continuous elemental carbon monitor or the Personal Dust Monitor for DPM measurement will be provided.

Jan 1, 2010

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

By I. AITKENS

The basic mining law of Cuba is contained in the basic Spanish mining decree having the effect of law December 29 , 1868. This legislation has remained substantially unchanged , with the exception of a few minor administrative changes made by the present Government . These changes provide for the register of mines , oil wells , and operations of such nature , and also provide for the keeping of records showing the value of minerals taken out . By Royal decree of April 17 , 1883 , the law of mines enacted for the Peninsula ( Spain ) on July 6 , 1859 , and the General Bases of December 29 , 1868 , were declared in force in Cuba . In order to encourage the mining of iron org , in 1883 the Crow of Spain issued a royal decree to the following effect.

Jul 1, 1931

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part 1 of the report contains the results of the field tests. The studies were made on an oil lease in a so-called "sour district," near Borger, Tex., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field test proved that aluminum lease tanks will withstand corrosion by hydrosulphide, but it as found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By Richard S. Olsen

Prior work by the Bureau of Mines demonstrated a feed preparation method that eliminates the formation of slime during leaching of calcined kaolinitic clay and makes leached residues fast settling and easy to filter. Nitric acid leaching rates determined for calcined kaolinitic clay prepared by this method were found to correspond to a zero-order reaction model for both batch and continuous, stirred-tank leach-ing. A rate constant of 0.136 min-1 was determined. Separation of solid residues from the reacted slurry was examined, and filtration rates were determined. Permeabilities of the flocculated, leached residues were around 51 darcys, or 5.0 x 10-7 cm2 for laminar flow through 4-ft-deep beds.

Jan 1, 1983

By Clarence O. Babcock

This report describes the results of Bureau of Mines laboratory and preliminary field tests on a rock bolt of helical shape. The flexible construction allows the bolt to maintain a more stable load level than is possible with a straight bolt. Bolt load changes resulting from anchor slippage, blasting shock, or changes in mine geometry with mining advance are minimized. Preliminary field tests were performed at the Kaiser Steel York Canyon mine where the load changes of straight and helical bolts were measured using a vibrating-wire load gage. The field tests were performed to establish the viability of the concept of a helical bolt. The practical usefulness in terms of performance and economics remains to be shown. The change in bolt load for the flexible bolts was one-third that for the straight bolts. There were no malfunctions of the gage, and the bolts maintained a more uniform load than the straight bolts used as controls.

Jan 1, 1978

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By John D. Sullivan

The recovery of copper by leaching from relatively low grade ores containing both oxidized and sulphide minerals is rapidly gaining in commercial importance. There is an economic limit below which certain ores can not be treated by concentration methods, and material with values below this limit must be discarded, possibly to be treated later, or the copper must be extracted by wet processes. Heap leaching has been carried out by the Phelps Dodge Corporation, Copper Queen Branch, for several years, and to-day its plant is a large producing unit. The Ohio Copper Coy at Bingham, Utah; has been leaching in place since 1919. Many other leaching operations are also being; carried out in various parts of the United States and in foreign countries. The plant at Rio Tinto, Spain, may be considered the father of heap leaching.

Jan 1, 1931

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed list of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have been modified as covered by extensions of the original approvals.

Jan 1, 1941

By B. W. Madsen

A modified transpiration apparatus was devised by the Bureau of Mines to permit rapid and accurate measure of the vapor transport and vapor diffusion coefficients of antimony sulfide (Sb2S3) and other compounds at temperatures to 1,045 K. The apparatus was equipped with dual condensers and valves to switch the flow of vapor in a fraction of a second from one condenser to the other, thus allowing short-interval sampling under equilibrium conditions. Reliability of the technique was established by measuring the vapor pressure of ZnC12 as a function of temperature and comparing the results with published data. As part of an investigation of the vapor concentrations and species of accessory element sulfides associated with copper and zinc smelting, the apparatus was used to measure the rate of vapor transport and diffusion coefficients of vapor over liquid Sb2S3 as a function of temperature between 870 and 1,045 K. The calculated vapor density was combined with published direct measurements of vapor pressure to calculate the average molecular weight of the gaseous species. Average molecular weight of the vapor in equilibrium with Sb2S3 ranged from 286 to 112 g/mol over the temperature range studied.

Jan 1, 1983