Search Documents

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By John R. Bradley

The object of this paper is to survey and analyze the bearing of economic nationalism, competitive sources of energy, and technologic developments on international trade in coal with especial reference to the competitive position of the leading coal-exporting countries in the Italian market, the largest in the Mediterranean region, and the Brazilian market, the second largest in Latin America. The political, economic, and financial disturbances caused mainly by the World War have resulted in an amazing situation. Especially since 1930 have conditions been complicated.

Jan 1, 1936

By Richard J. Mainiero

The Bureau of Mines has developed a prototype nonincendive explosive rock-breaker charge that can be fired unconfined in underground bituminous coal mines without the danger of igniting a flammable atmosphere that might be present. At present, unconfined shooting in underground coal mines is prohibited, but there are situations where the use of such shots would yield an overall improvement in safety. The charge consists of l-1/2 lb of permissible water gel explosive in the form of a short cylinder 7 inches in diameter and 7/8 inches high, surrounded by a l/2-inch-thick layer of damp salt, and encased in latex rubber reinforced with cheese cloth. The latex rubber housing provides a charge package that is strong enough to resist rough handling yet is pliable enough to conform to an irregular stone surface. A charge of this shape was found to be more effective at breaking rock than charges with lined or unlined cavities. Incendivity tests in a gallery have shown that the prototype charge will not ignite a flammable methane-air atmosphere when fired. Rock- breaking tests made with limestone boulders indicate that the charge will satisfactorily break stone slabs weighing 1 to 2 tons, and that two or more charges might be effective for slabs weighing up to 10 tons. In cooperation with the Mine Safety and Health Administration (MSHA), a test protocol for the certification of these charges as "permissible" for use in flammable atmospheres is being developed.

Apr 1, 1982

By Cliff McCartney, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research to evaluate and improve remote mine seal construction technology for mine fire control and suppression. The main focus of this work is to develop reliable technology that will remotely seal a mine opening from floor-to-roof and rib-to-rib. NIOSH, in partnership with Strata Mine Services Inc.1, is evaluating the capability of a two-component phenolic foam-based product, called Rocsil®1, that is intended for cavity filling, air and gas sealing, and consolidation of highly fractured strata. Rocsil® can be rapidly applied, has a quick cure time, a high expansion rate, good compressive resistance and excellent anti-static properties. When the resin and catalyst are mixed, an immediate foaming reaction occurs followed by rapid expansion up to 30 times the original volume. By virtue of its fire-resistance properties, Rocsil® foam has application for sealing underground mine areas undergoing heating from spontaneous combustion and it could be useful for remote mine seal construction to aid in mine fire control and suppression. This paper presents an overview of remote mine sealing technology, introduces the use of Rocsil® foam for remote mine seal installations, offers a case study of the use of this rigid foam material to remotely construct a temporary in-mine seal and discusses technology improvements. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

By P. A. Cox

Guidelines are provided for the design of explosion-proof electrical enclosures that will meet MSHA certification requirements according to Part 18, Title 30, of the Code of Federal Regulations, and fulfill their intended service underground. The guide covers only those aspects of design which affect enclosure strength, ruggedness, endurance and flame path, i. e., the enclosure ability to properly contain an internal explosion. Internal static and explosion pressures, external impact and thermal heating load are treated as well as the proper selection of materials and welding procedures.

Jan 1, 1985

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By Walter Pajalich

This Bureau of Mines report is a study of the organizational framework of the ferrous scrap industry, of the products produced, and of the factors affecting the consumption of ferrous scrap by the steel industry. Consumption data from 27 major iron and steel firms in the States of Illinois, Indiana, Iowa, Michigan, Minnesota, and Wisconsin during the period between 1957 to 1962 were grouped by type of iron and steel furnace production facilities to determine consumption pattern for various grades of scrap in comparison to ingot production, hot metal consumption, and home scrap generation. Grades of scrap affected by changes in scrap consumption were determined, and the pattern that emerged was analyzed. Correlation of scrap demand and its effects on scrap prices based on price of scrap receipts of No. 1 heavy melting scrap and No. 2 bundles in the Chicago area for the years 1957 through 1962 indicated that demand trends do not always affect the price of scrap, Past and present technological advancements in steelmaking processes are discussed, and their effects on the scrap industry are analyzed.

Jan 1, 1967

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By D. Harrington

"Up to the last 10 or 15 years, responsibility for accidents in mines was generally, though not universally, placed upon the person or persons immediately involved. Present-day thought is rapidly veering toward holding the industry responsible for accidents, with ultimate payment of the bill by the consumer, if financial expenditure should be necessary. While it is undoubtedly correct in principle that responsibility for accidents in and around mines should be shouldered by the employer and while it is probable that as time passes the burden will become even more definitely than now that of the mining companies, on the other hand it is an undeniable fact that large numbers of accidents occur through acts of omission or of commission of some person, very frequently the victim of the accident being the offender.Out of about 3,000 persons killed every rear in our -mines and quarries, nearly half or approximately 1,500 of the fatalities are due to falls of overlying material or of persons, about 500 to haulage, about 350 to fires and explosions, about 125 to explosives, approximately the same number to electricity, and about 300 to various miscellaneous accidents.Generally the accidents from falls involve but one or two persons at a time, and the tendency is now as it always has been to charge the victim or possibly a coworker with the responsibility. Usually this sort of accident occurs at or near a working face (statistics indicate that about 80 per cent of fatalities from falls of roof or rib occur near the face), and as it is Generally agreed that it is the duty of the worker to keep his working place safe, the worker and especially the face worker is given the blame in case of accident."

Apr 1, 1930

By L. D. Tracy

"The first study of this subject has been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal—mining industry to standardise the forms of leases, and so avoid some of the abstruse and ambiguous clauses which may be found in many of then and the consequent liability of costly litigation.In some of the publications of the Illinois Mining Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the State have been dividedinto eight geological districts, each district being treated separately.report covers District No. VI of that classification, and it is hopedstudies of the other districts will be completed in the near future and similar results published.The report includes a short description of the geological condition the character and quality of the coal and the nature of the surface, data for which have been taken largely from the Illinois Geological Survey publications.Mining methods and percentages of recovery are mentioned, together physisal conditions, market and transportation facilities, because all of these factors have a bearing on royalties and leasing conditions."

Jan 1, 1926

By F. W. Lee

The paramount importance of water to life of all forms on the earth is too well known to require elaboration in this brief paper. It has repeatedly been termed the most valuable of all our mineral resources. Its importance is justifiably recognized in the extensive areas covering the earth which receive sufficient rainfall to sustain a relatively luxuriant vegetation; but in those areas where rainfall is insufficient to support anything but a relatively meager plant growth, the location of a water supply and its development become of even more vital interest to those attempting to obtain a living from the soil. Geological investigations concerning the water supply of the United States have been most extensive, important work having been accomplished by Federal, State, and local governments and by private enterprise. A casual examination of the titles of the 739 Water-Supply Papers published by the United States Geological Survey3/ alone testifies 'to the vital nature of our water resources and the extensive work that has been done on them.

Jan 1, 1936

By E. W. GOODWIN, V. F. Parry, J. B. Goodman, L. D. Schmidt, J. D. Davis, A. C. Fieldner, W. S. Landers, J. L. ELDER

The Heliopore process is essentially an arrangement that uses the waste heat in the exhaust gas of an internal - combustion engine to carbonize coal (noncaking ) or lignite . The gases distilled from the coal furnish fuel for the internal - combustion engine , which drives an electric generator . Thus the main products of the plant are electricity and char . A flow diagram illustrating the principles of operation of the Heliopore process is given in figure 1. The primary equipment consists of a carbonizing retort , gas cooling and scrubbing equipment, a gas storage holder, and an engine to burn the gaseous carbonization products . Coal is charged into the top of the retort while the hot gases from the engine travel upward through special ducts in the retort countercurrent to the coal flow . The hot gases never come into direct contact with the coal . Char is discharged at the bottom of the retort and hot gases at the top . The gaseous products resulting from carbonization of the coal are drawn off by an exhauster through the condensing and scrubbing equipment to take out tar and liquor , then to a gas holder , and finally are burned in a gas engine . The gas engine drives an electric generator and the engine exhaust gases are returned to the retort to carbonize coal . The entire process was intended to be continuous and self - sustaining, and to use coal as the only fuel . The plant may be said to be a large - scale pilot plant in that , although it is of full commercial size , its main purpose is to provide data for the design of others of its type . The installation tested had a daily throughput of about 4 tons of coal . Figures 2 , 3 , and 4 picture some details of the plant and equipment used in the experimental testing . Further details of the equipment and engineering drawings of the castings are shown in figures 8 to 22 in the Appendix .

Dec 1, 1943

By Bertrand L. Johnson

Before 1914 , Chile , because of her extensive resources of natural nitrates , practically monopolized the world markets for one of the leading fertilizer materials . Since nitrogen also is an important war material , constituting in fact the principal ingredient in many high-powered explosives , the World War and the widespread insistence upon national self- sufficiency for war materials brought about the development of nitrogen fixation plants in all of the larger countries . The production of by- product ammonia from gas and coke plants was likewise stimulated . As a result , Chile , even after the ocean lanes were reopened , was forced to fight for her lost markets . Since the world capacity to produce is still far in excess of annual consumption , the competition between natural and synthetic supplies has been keen and prices have fallen below pre-war levels . Chile has recently succeeded in unifying her industry , utilizing the most efficient process now in operation, and the Government is a partner in the new company that will take over all of the present producing companies . These developments place Chilean nitrate of soda , in a much more favorable position among the markets of the world . More intense competition will undoubtedly follow and , in order that those interested may become familiar with the fields upon which the nitrogen conflicts of the near future may be waged , the following general summary of the nitrogen industry has been prepared .

Jan 1, 1931

By Sidney Katell

This report, covering the period January 1969 through December 1969, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the 11th in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost. Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing.

Jan 1, 1970

By R. B. Prater

The Bureau of Mines conducted research to separate the F from byproduct Zn concentrates obtained from fluorspar (CaF2) production, as part of the Bureau's effort to devise efficient, environmentally acceptable technology for recovering Zn from resources considered undesirable by Zn producers. Sulfuric acid (H2SO4) was found to be effective in F removal, while ammonium carbonate [(NH4)2C031 was not. The most important variables for reducing the necessary residence time were found to be temperature and agitation. Optimum leaching conditions were 75° C and 500 r/min for 2 h at 40 pct solids with 0.2 g acid per gram of concentrate, which resulted in a 98.3-pct F extraction. Zinc losses during F removal were in the range of 2 to 3.3 pct. Other elements such as Fe, Cd, Ca, and Cu were also partially dissolved. About 93 pct of the F was removed from the leach solution by neutralization and precipitation with calcium hydroxide [Ca(OH)2]. Additional treatment might be necessary to limit the buildup of soluble elements in the recycled leach solution.

Jan 1, 1985

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By X. Shi, K. S. Kaspnak

"The generation of free radicals from reactions of nickel (Il)-thiol complexes with molecular oxygen and model lipid hydroperoxides was investigated by electron spin resonance (ESR) utilizing 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as a spin trap. Incubation of nickel (II) [Ni(II)) with cysteine in an aerobic environment generated hydroxyl (·OH) radical, which then reacted with cysteine to generate a carbon-centered alkyl ( · R) radical. Radical generation was inhibited under a nitrogen atmosphere. Model lipid hydroperoxides, cumene hydroperoxide, and I-butyl hydroperoxide enhanced the yield of these radicals and also generated an alkoxyl (·OR) radical. Radical yield decreased by approximately half under a nitrogen atmosphere. Although histidine did not cause radical formation in the reaction between Ni(II) and cumene hydroperoxide under aerobic conditions, the addition of histidine to a mixture containing Ni(ll), cysteine, and cumene hydroperoxide under the same experimental conditions increased the yield of · R radical but lowered the yield of ·OR and ·OH radical adducts. It thus appears that histidine caused the ·OH attack to be more site-specific. Similar results were obtained utilizing 1-butyl hydroperoxide. Penicillamine or N-acetylcysteine yielded similar results except that under aerobic conditions, reaction between Ni(ll) and N-acetylcysteine without hydroperoxide did not generate a significant concentration of free radicals. Under the same experimental conditions, cystine did not generate any detectable free radicals, suggesting an important role of the -SH group in Ni(II)-mediated free radical generation. The results indicate that free radical generation from the reaction of Ni(Il)-thiol complexes and molecular oxygen, and/or lipid hydroperoxides, may play an important role in the mechanism(s) of Ni(II) toxicity and carcinogenesis. INTRODUCTIONWhile nickel is a well-recognized carcinogen [l, 2]. the underlying biochemical mechanisms remain unclear (3, 4). Recent studies suggest that these mechanisms may involve oxidative DNA damage through free radicals, especially the hydroxyl (•OH) radical [5-13]. The mechanisms of nickel carcinogenicity and toxicity may also involve lipid peroxidation [14-21]. Unlike ferrous ion [Fe(II)], the Ni(II) cation itself does not directly react with 02, H2O2, or lipid hydroperoxides to generate free radicals [12, 21]. However, it has been reported that Ni(II) complexes with certain synthetic oligopeptides, e.g., tetraglycine or glycylglycylhistidine, make Ni(II) reactive with 02. This reaction results in transitory formation of Ni(III) and degradation of the organic ligand via free radical reactions [22]. Such Ni(II)-peptide complexes are also capable of reacting with H2O2 to produce oxygen free radicals [11, 12]. Although the cellular environ¬ment may not contain these particular peptide ligands that are known to render Ni(II) redox active in vitro, it does contain a variety of oligopeptides that are capable of forming Ni(II) complexes at physiological pH, and thus may facilitate Ni(II) redox activity in vivo. These oligopeptides include glutathione (y-L glutamylycysteinylglycine), carnosine (homocarnosine (y aminobutyryl-L-histidine), and anserine ( B-alany1-3-methyl-L-histidine)."

Nov 1, 1995

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a simple and accurate method for calculating the viscosity of gas mixtures. Only the composition of the mixture and the molecular weights and viscosities of the pure components in the mixture are required. The momentum fraction of a mixture is calculated from the composition. The fluidity is calculated as a quadratic function of the momentum fractions. The efficiency factor for transfer of momentum in collisions between bodies of different masses is derived and used with one empirical constant. The viscosity is the reciprocal of the fluidity. Results of the method are compared with 752 reported viscosities for 40 dilute binary systems at temperatures from -78 to 276.9°C. Using this method the average absolute deviation is 1.29%, the root-mean-square deviation is 1.99%, and the average deviation is -0.84%.

Jan 1, 2010