Search Documents

By D. A. Larson

This is the second in a series of Bureau of Mines reports which de-scribe experiments designed to devise an efficient, economic mechanical fragmentation technique for hard rock. The previous study described the development of the ripper cutting technique to successfully cut hard rock with 3-to 6-in-wide drag cutters. This study was conducted to test the ripper cutting technique at full scale using 9-in-wide drag cutters. The experiments were conducted with a special test device that cut shallow, 6-by 6-ft openings in 9,200-lbf/in2 compressive-strength concrete blocks. The tests showed that ripper cutting can excavate large-scale openings of the type required by the mining industry at a production rate that outperforms the conventional drill-blast technique. Moreover, the system can produce openings of various sizes and shapes, is simple to oper-ate and maintain, and produces very little dust or noise during operation. The system appears to meet all of the criteria for a successful hard-rock mining machine.

Jan 1, 1987

By Oliver Bowles

"Asbestos" is not the name of a distinct mineral species but is rather a commercial term applied to fibrous varieties of several minerals. The origin and significance of names applied to asbestos by early writers are discussed in the section devoted to sources of supply and terms employed in ancient times. VARIETIES The most useful variety of asbestos is chrysotile, a fibrous serpentine the composition of which is expressed by the formula H4Mg3Si209. Chrysotile is characterized by a strength and flexibility that permit the use of the longer fibers for spinning. The bulk of the world production of both long and short fibers, is of this variety.

Jan 1, 1935

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By S. M. Shelton, A. L. Engel

The carnotite deposits of western Colorado and adjacent sections of Utah and Arizona were formerly an important source of radium and uranium until displaced by the exploitation of foreign deposits in the Congo and northern Canada . Recently interest has been renewed in domestic carnotite ores as a source of vanadium . Carnotite is a canary - yellow, crystalline , pulverulent mineral occurring in sandstones in the Colorado - Utah district as an incrustation on the faces of joints and fractures and deposited around and between individual sand grains , often strongly adhering to the surface of the grains . Chemically, it is a variable combination of potassium, uranium , and vanadium oxides with water of crystallization . It is soft and friable , and occurs in fine - grained or earthy form . In spite of a specific gravity of 4.1 , gravity concentration has not proved practical as a means of beneficiation because of the earthy texture of the mineral . Vanadiferous sandstones occur with minerals ranging from roscoelite (vanadium mica) , containing little uranium , to high- uranium and low -vanadium carnotite . There is considerable local variation in the texture of the ores . The treatment of carnotite ores has been described previously , with attention directed to the elimination of waste in mining and the extraction of radium . The suggested methods included those suitable for the recovery of vanadium , since both radium and vanadium occur in the same minerals . Moore and Kithil suggested crushing from 40- to 80 - mesh with rolls , accompanied by a rubbing action to loosen the carnotite adhering to the sand grains . Fine grinding was to be avoided because it diluted the final product too much . The crushed and rubbed material was to be washed and

May 1, 1942

By Oliver Bowles

The United States has never attained importance as a producer of asbestos, the domestic output being only 1 to 3 percent of the quantity required to supply raw material for its extensive asbestos-product manu- facturing industries. Production is centered in four principal countries-- Canada, Rhodesia, Union of South Africa, and the Soviet Union. Since asbestos first became an important commercial commodity the Province of Quebec, Canada, has led in tonnage produced, but a large proportion of the output of this province is shorter, nonspinning grades. Since 1916 the Union of South Africa and Rhodesia have become increasingly important as sources of the higher-grade spinning fibers. Before the World War Russia ranked next to Canada as a producer of asbestos, but during the revolution- ary period the industry in that country was almost at a standstill. In 1926, however, activity was revived, and each year since then production and exports have increased greatly. Minor quantities of asbestos are produced in Cyprus; Australia, Finland, and several other countries. Chrysotile is the leading product in all the producing countries, but substantial quantities of both blue (crocidolite) and brown (amosite) asbestos also are produced in the Union of South Africa. Minor quantities of anthophyllite and similar amphibole varieties are mined in the United States, Italy, Bulgaria, Finland, and several other countries.

Jun 1, 1934

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

This appendix contains the list of equipment, their corresponding number and their specifications with the quotations from the vendors/ manufacturers who can supply this equipment. The listings are arranged by process plant areas.

Jan 1, 1979

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 120 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257; 7267,`7273; 7285, 7292, 7303, 7310, and 7324. 1. GRAVITATIONAL METHODS 7933. Ansel, E. A Eine Untersuchung zum Problem der Isostasie (An Investigation Regarding the Problem of Isostasy). Gerlands Beitr. Geophys., Leipzig, vol. 59, 1942, pp. 16-26.

Jan 1, 1945

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By H. L. Gibbs

Many factors contributed to the decision to build a radiochemical laboratory at the Salt Lake City Metallurgy Research Center to investigate the application of radioactive isotopes and chemical compounds in extractive metallurgy. These reasons included the notable success achieved in biological sciences with radioisotopes, the development of reliable instruments and methods for identifying the isotopes and measuring their activities, and the commercial availability of radioisotopes in a variety of forms and known activities. The paramount reason, however, was the realization that better methods were needed for guiding and quantifying research to resolve the complex extractive metallurgy problems under study at the Research Center. This is the first of a series of reports describing the application of radioisotopes and radioactivity techniques in extractive metallurgy. The report includes a discussion of licensing and safety requirements, a general description of the laboratory and the methods used, a definition of the nature and scope of the research program, and a synopsis of the more important problems studied. Subsequent reports will concern radioactive techniques for solving specific problems in mineral dressing, hydrometallurgy, and pyrometallurgy.

Jan 1, 1960

By C. Melvin Lepper

High-resolution shallow seismic reflection methods are being used by the Bureau of Mines to map underground geologic features in coal mines. These features include faults, channel sand, washouts, rolls, and steep dips. The seismic method is proving useful for locating all of these at reasonable cost and with better definition than available with drill programs alone. This report provides a capsule description of the techniques and their application to mine planning.

Jan 1, 1976

By D. S. Kingery

Investigations over several years have disclosed that the principal manners of occurrence of shuttle-car injuries are in order: 1. Victims in contact with roof or crossbars. 2. Victims in contact with ribs or timber legs. 3. Victims falling from, or jerked from, shuttle cars. 4. Victims in contact with overhanging brows or protruding pine for pin timbers, or water lines. 5. Contact with persons or collisions with parked equipment. 6. Victims injured by roof falls or falling timbers caused by knocking out roof supports with shuttle cars. 7. Victims injured by runaway shuttle cars. 8. Victims injured while loading or unloading timbers or other materials from shuttle cars. These recurring types of shuttle-car accidents reflect the physical conditions of the working sections, certain safety deficiencies in shuttle-car maintenance and design, and unsafe practices by operators.

Jan 1, 1952

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By David N. Montgomery

The characteristics of a closed cavity acoustic coupler were measured. Various configurations were investigated to determine their feasibility for use in a portable audio dosimeter calibrator.

Jan 1, 1976

By Oliver C. Ralston

The growing popularity of perlite (sometimes spelled pearlite) as a raw material for thermal expansion into pumicelike products in the Western States has prompted a preliminary investigation of the properties of such material and the problems that want solution to put a perlite industry on a firm foundation. The Bureau of Mines is undertaking the gathering of data and the solution of these problems, and the following paper records some of the available information. and the promise of the material, with some comparisons of advantages of the various competing lightweight aggregates that can be made from siliceous volcanic glasses and rocks containing entrapped or dissolved water that causes their expansion on' quick heating to their softening points. This new industrial rock has caught the fancy of the mineral industry in the western States because it has Fume advantages over natural pumice. Chemically, it is typified as rhyolitic in composition, and one may find obsidian, rhyolite, pumice, pumicite, and perlite from the same vant and contemporaneous in origin. The material need not be rhyolite but should be a siliceous or acid lava and contain 2 to 5 percent water still in "solution" in the rock. On quick heating to the softening temperature the material puffs, due to conversion of the contained eater into bubbles of steam. Slow heating causes gradual release of the imprisoned water by decrepitation and. cracking and-results in, very little puffing. Perlite is often in the form of ovoid volcanic bombs formed by explosive eruption of large masses of lava into the air, where they, quickly cool, with escape of little of the contained water, exceptt perhaps for a hollow interior. Since they cool in layers they have an onion-type structure and a pearly luster from interference of light between the. layers, which is' the origin of the name "perlite." Perlite may occur in intruded flows that have been quickly cooled and partly expanded but retained most of their magmatic water content. Obsidian may be the same lava cooled quickly under conditions that prevented crystallization of feldspars and other minerals, leaving the volcanic glass that may or may not retain all of the original contained water.

Jan 1, 1946

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By A. L. Engel

As a part of the program of the Rare and. Precious Metals Experiment Station, Reno, Nev., in connection with investigations of treatment methods for precious and precious-base metal ores, to further conservation and recovery of precious and base metals, tests Were made on samples from the Buzzard Mine, located in the vicinity of Placerville, Calif. These samples represented ore exposed during previous development work, in tunnels and a shaft on the property, including highly oxidized material from the surface zone and sulfide ores from depths of 150 to 300 feet. The surface samples contained little base metal and only enough gold 80 that economic exploitation of them would depend on development of a large tonnage of ore, low-cost mining methods, and satisfactory treatment methods. The sulfide samples were valuable enough to warrant further exploration and development and, if present in suitable tonnage, the installation of a treatment plant for recovery of both precious and base metals. The oxidized surface-zone samples carried 0.11 to 0.14 ounce gold per ton. Standard amalgamation and flotation tests of these samples gave low recoveries. Standard cyanidation tests indicated high consumption of lime and cyanide and gold extraction of 79.4 and 82.7 percent. Water-leaching the ore after crushing to minus 10-mesh improved cyanidation considerably. Ex-tractions of 82.7 to 85.8 percent were obtainec1 with lime consumption of 6 to 7 pounds per ton of ore and cyanide consumptions of 1 to 4 pounds. Grinding the samples to minus 200-mesh followed by water-leaching and cyanidation gave improved extractions of 91-92 percent of the gold, but with slightly increased consumptions of lime and cyanide.

Jan 1, 1949