Search Documents

By R. B. Porter

Bench-scale tests were performed by the Federal Bureau of Mines on lignite and subbituminous coal at pressures to 1,000 p.s.i.g. (pounds per square inch gage) in atmospheres of hydrogen or nitrogen to obtain information concerning the influence of pressure on carbonization of normally noncaking coals. The distribution of gaseous, liquid, and solid products as a function of processing pressure was determined. Except for special experiments, the carbonization was at 940° F. In a hydrogen atmosphere above 400 p.s.i.g., agglomeration of the solid residue (especially with lignite) became noticeable and increased directly with the processing pressure. Although in some instances the solid particles fused together, the mechanical strength of the agglomerate was always low. On the basis of visual inspection, the coals agglomerated in the following order of decreasing intensity: (1) Steam-dried lignite; (2) lignite; and (3) subbituminous coal. Addition of lignite tar in quantities to 25 percent by weight of charge did not increase agglomeration or change the carbonization characteristics of the coal.

Jan 1, 1961

By Wesley Holmes

Concentrating, nodulizing, and smelting studies were conducted at the Albany Metallurgy Research Center of the Bureau of Mines to determine whether (1) western iron ores of the type found in the Carter Greek deposit near Dillon, Mont., could be utilized; (2) concentrates of acceptable grade with good iron recovery could be attained by wet-magnetic beneficiation; (3) nodulized concentrates could be smelted with reductants readily available in Montana; (4) iron concentrates could be smelted without prior agglomeration; and (5) high-purity iron could be produced directly from high-grade concentrates, Three small samples and two tonnage samples from the Carter Creek deposit were uniform in chemical composition, and their iron content averaged about 31 percent. They were found to be banded gneisses, and magnetite was the principal iron-bearing mineral.

Jan 1, 1962

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By L. C. IlsLey

"This paper is intended for State mining inspectors, safety engineers of mining companies, and others interested in electrical safety inspection in mines, It presents the important points that should be watched by inspectors, and briefly reviews the work of the Bureau of Mines in the testing of electrical apparatus or equipment to determine their permissibility for use in gaseous coal mines.Important Points in Inspecting Mine Electrical Installations or Equipment.The following questions are intended as suggestions to a safety inspector who may not have been specially trained in looking for defects in installations or in the maintenance of electrical equipment:1.,Is there someone in charge of electrical equipment who is fitted for this position by ability, training and experience?2.,Is a systematic recorded inspection of electrical equipment made at least once each month?3.,Is a plan map of the mine kept showing all permanently installed electrical machinery and apparatus, including cables, conductors light etc.?4.,Are there instructions for resuscitation from electric shock posted in each surface and underground electrical station, also at the entrance of the mine and in the first aid station and are employees working on electrical equipment trained to apply these instructions in case of accident?"

Nov 1, 1923

By John A. Organiscak

[Fugitive Just is generated alone unpaved mire reads from intermittent equipment traffic. Typically, the majority of such traffic consists of trucks hauling either mine product or waste [rum the surface mime pit and/or the processing plant. Fugitive dust generated along these unpaved mine roads includes particles of all sizes which become airborne. The potential hazards include the deleterious effects to human health of inhaled dust, traffic visibility hazards and environmental impacts on the localized area by the larger-sized visible airborne dust. Two held surveys were recently conducted to quantify fugitive dust generation and dispersion from truck traffic on unpaved and untreated mine haulage roads For these surveys., airborne glow sampling was conducted at multiple sampling fixations away from an unpaved haulage road at a limestone quarry/plant and at a coal mine preparation plant lo measure the size characteristics, concentrations. and dispersive behavior of the dust cloud generated from truck traffic- Results show that at least 80% of the airborne Just generated by haul trucks was larger than 10 µm- Airborne respirable, thoracic, and total dust concentrations all decreased and approached background concentrations 30.5 in (100 feet) from the road This report describes the average and instantaneous peak dust levels that were measured tip to 30.5m (100 feet) Iron the haulage road. Keywords: Unpaved mine road, fugitive dust, silica.]

Jan 1, 2008

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By L. H. Johnson

"INTRODUCTION The Pennsylvania anthracite industry produced 53 million net tons of anthracite during 1945. Fifty-one million tons was prepared for the commercial market (3), 3/ and 2 million tons (consisting of fine sizes) was used for colliery power consumption. Of the number of tons prepared for market, 17 million tons (33 1/3 percent) was prepared by the use of acid mine water treated with lime.Mine water from underground workings is pumped, drained, and stored in huge quantities. The mine-drainage systems in the anthracite region handle over 200 billion gallons of water annually, of which 150 billion gallons is pumped to the surface. More than 69 billion gallons of water is impounded in underground pools (1). Much of this water is employed for breaker use, dust-control installations; hydraulic backfilling, combatting mine fires; and aiding in the transportation of anthracite in gently dipping places where sheet iron is used Roos(4) estimates that 1,100 gallons of mine water is utilized in the preparation of anthracite mined."

Nov 1, 1946

By H. F. Weaver

The 19th National First-Aid and Mine Rescue Contest was held in the Civic Center, Charleston, w. Va., on October 2, 3, and 4, 1961. The meet was sponsored by the Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other groups interested in safety. The Arrangements Committee, as authorized by the General Committee, made the necessary arrangements for conducting the 1961 contest. Members of the Arrangements Committee were: George Trevorrow (chairman), Bituminous Coal Operators' Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; Harry Gandy, Jr., National Coal Association; and James Westfield, Bureau of Mines.

Jan 1, 1962

By A. F. Jolly

In an effort to better predict the useful service life of friction rock stabilizer mine roof bolts in coal mine environments, the Bureau of Mines has evaluated the corrosion resistance of stabilizer steels in air-saturated and deaerated waters from seven Eastern and Midwestern underground coal mines. Accelerated electrochemical corrosion tests were used to estimate corrosion rates for the two high-strength, low-alloy (HSLA) steels used to fabricate Split Set stabilizers and for galvanized steel. Long-term static-immersion weight-loss tests were also conducted with the HSLA steels. Corrosion rates developed from the weight-loss tests (steady-state air dissolution) were roughly comparable to rates determined from electro-chemical testing in aerated waters. Although the highest rates occurred in waters with the highest chloride contents, rates in the other waters were low (<2.0 mpy) and exhibited little correlation to the widely varied chloride contents of the waters. The generally low corrosion rates are attributed in part to the tendency to deposit a protective CaC03 film, reflecting susceptibility to carbonate precipitation as indicated by positive Langelier (saturation) index values for the waters. With one exception, corrosion rates for the galvanized steel were (2.0 mpy. Rates with aerated waters were higher than those with deaerated waters. Pitting tendencies of the steels were also estimated.

Jan 1, 1987

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By D. Christofferson

This final report documents the cooperative efforts of the Engineered Systems Division and the Mining Equipment Division of FMC Corporation during performance of Bureau of Mines Contract H0252091. Improved operator compartments incorporating overhead canopies, logical arrangements of controls, and design features offering greater operator comfort were developed and retrofitted to the FMC 320A roof bolter and 6L shuttle care The vehicles were evaluated in underground operations at separate mine sites. The successful evaluation has resulted in incorporation of the designs as standard features of the 320A roof bolter, and the 5L, 6L, and 10L shuttle cars.

Jan 1, 1978

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By John E. Pahlman

An increasing number of gold and silver mining operations are employing cyanide solutions to effectively dissolve silver and gold from finely disseminated ores. Many of these operations use small, packaged processing systems like the State of Maine filter system, which employs zinc precipitation of gold and silver. Solution-clarifying filters in these systems become blinded with calcium carbonate (CaC03) scale and require frequent (every 2 to 10 days) dismantling of the filter units for acid cleaning, This is a hazardous operation as it is not compatible with the alkaline cyanide leach solutions and may result in the evolution of toxic hydrogen cyanide (HCN) gas during cleaning and during any accidental acid spill. The Bureau of Nines has investigated an alternative, nonacidic method of cleaning blinded State of Maine filters that employs ethylene- diamine-tetraacetic-acid (EDTA) type chelating agents to dissolve the scale. In situ cleaning of a 150-st/d State of Maine filters with EDTA- type chelating agents was successfully demonstrated. Greater than 90 pct of the CaC03 scale was removed in about 10 min with circulation of 31 L of 2.5-pct-EDTA solution through the filter unit. The EDTA cleaning method not only eliminates the cyanide hazard in filter cleaning but is advantageous from the standpoint of operating costs and productivity.

Jan 1, 1986

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

By M. J. Lempel

A theoretical study of the heat-transfer characteristics of a dilute gas-solids mixture in an externally heated tube is reported. Detailed equations are developed describing the system, and a numerical method is presented to solve the equations using a digital computer. The methods are applied to a system containing fine coal particles entrained in hydrogen, flowing through a hot tube. Heat-transfer coefficients and several other physical constants are evaluated in detail.

Jan 1, 1967

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963

By A. Gene Collins, Cynthia A. Pearson, Cathy J. Waters

The chemistry of selenium and tellurium is discussed , along with a method of preparing a synthetic oilfield brine , an oilfield brine sampling method , and methods for determining selenium and tellurium in complex oilfield brines . Selenium either can be reduced to the elemental form with sulfur dioxide and determined semiquantitatively by color comparison of the red amorphous form or can be converted to selenite and determined quantitatively by reacting it with 3,3 ' - diaminobenzidine and obtaining its spectral absorbance at 420 mu . Tellurium can be reduced to the elemental form with hypophosphorous acid , and the spectral absorbance of its red hydrosol can be measured at 400 mu . Less than 0.05 mg / 1 of selenium and 0.1 mg / 1 of tellurium can be determined by the described methods .

Jan 1, 1964

By D. W. Bridges, L. Crocker, R. O. Dannenberg

About 95 pct of the beryllium was dissolved from most ore samples by agitation leaching with 600 lb of H2SO4 per ton of ore for 24 hours at 65 ° C and 35 pct solids . Leach slurries generally were viscous , and the limiting pulp density for thorough mixing was about 35 pct solids . Settling of the leached pulp required 0.6 to 0.8 lb of a polyacrylic flocculant per ton of ore leached with 600 lb of H2SO4 per ton , whereas ore leached with 800 lb of H2SO4 per ton required only 0.2 to 0.3 lb of flocculant per ton . Terminal densities of the settled pulps were about 28 and 35 pct solids , respectively , from leaches using 600 and 800 lb of H2SO4 per ton . Vacuum filtration of settled pulps at 15 in . Hg resulted in a filter cake containing 50 to 59 pct solids . Roasting the ore at 500 ° C before leaching increased the limiting pulp density for effective mixing to 50 pct solids . Acid requirements , however , were not diminished , although leaching roasted ore with 600 lb of H2SO4 per ton resulted in densification of settled pulps to about 40 pct solids . Filter cake from leaching preroasted ore contained about 20 pct less water than that from unroasted ore .

Jan 1, 1963