Search Documents

By G. St. J. Perrott, N. A. Tolch

"The testing of explosives for permissibility for use in coal mines was begun by the technologic branch of the United States Geologic Survey in February, 1909, and continued by the United States Bureau of Mines from July, 1910; this testing has been carried on from year to year as the explosives were submitted by manufacturers. As a result of these many years of testing for permissibility a large amount of data has accumulated regarding the characteristics of permissible explosives. The manufacturer expects a sample of explosive submitted for test to meet the requirements for permissibility, otherwise the sample would not be submitted. However, in spite of the careful regulation and preparation of the formulas a certain percentage of explosives fails to pass the gallery tests. It is therefore interesting to note the proportion of failures at the gallery for a given composition of explosive. The fact should be emphasized that this discussion deals with all explosives submitted for test, both those which passed the tests and those which failed to pass. Explosives that failed to pass the tests were never designated as permissible explosives and have never appeared on any list of explosives permissible for use in coal mines.The Bureau of Mines classifies permissible explosives in two ways, according to the quantity of poisonous gases produced and according to the characteristic ingredient of the explosive.4 In this paper only two types of the latter classification are considered, as follows:"

Dec 1, 1929

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By A. W. Ambrose

"Those having an intimate knowledge of the relation between production and consumption of crude oil in the United States have realized for some time that production will not be able to keep pace with consumption. The American public has had this called forcibly to its attention by the increased prices of gasoline and crude oil, and by the recent shortage of gasoline on the Pacific Coast. In substance, each year we are consuming millions of barrels of oil more than we produce, and this deficit must be made to by importations. A careful analysis of the situation makes it evident that we need every barrel of oil that can be produced.Need for the Petroleum Production Engineer.Under present production practices perhaps 80% of the oil still remains in the sand. (See Lewis, J.O., Methods for increasing the recovery from oil sands, U. S. Bureau of Mines, Bulletin 148 p. 8.) Many wells are making water, and even whole pools are being flooded. The burning of fuels under field boilers is not generally efficient, and often gas is not made to do its full duty in bringing the oil to the well.In the past the producer has had to combat these and other problems single-handed. He has been too busy to give them special attention, and he has had little competent engineering advice. Oil, gas, and water occur underground according to certain natural laws. Undoubtedly an engineer, who is familiar with production practices and understands the fundamentals of the accumulation of oil and gas, can be of service to the producer by specializing on certain problems with a view of getting mare oil from the sand. In every other enterprise of similar magnitude the engineer is regarded as a necessary unit to its operation, and he should be so in the production of oil. His field of work should extend to every phase of production in which science and engineering and geology"

Sep 1, 1920

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By W. A. Dunkley

During the past year and a half the Western United Corporation of Aurora , Illinois , has been distributing carburetted water ges from its Lockport , Ill . , plant , to an extensive territory , under an initial pressure ranging up to 90 lb.. per sq. in . The most distant distributing point on the system is at Harvard , Ill . , about 35 miles from the plant.. The territory supplied is approximately 85 miles long and 35 miles wide , the total mileage of rains being 1223 , or approximately 24 per cent of all the gas trains in Illinois outside the city of Chicago .

Feb 1, 1923

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977

By Joseph Chalmers

Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the "gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ultimate recovery of oil from their properties. A number of factors influence the efficacy of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity show a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate of gas injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.

Jan 1, 1930

By G. A. Appell

"INTRODUCTION During the summer of 1945, the Bureau of Mines conducted an investigation and program of churn drilling near the village of Tennyson in Grant County, Wis. The work was undertaken as part of a general investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the war program.The area for special investigation was selected on the basis of favorable structural disclosures, evidence of widespread zinc mineralization, absence of any great amount of exploration to depth beneath the productive shallow workings, and the favorable results of several churn-drill holes in the village of Tennyson.During the Bureau's investigation, 30 churn-drill holes aggregating5,888 feet were completed.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to-the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual. Investigative work, and prepares the final report.The work described herein was accomplished under the direct supervision of Francis C. Lincoln and the author, mining engineers of the Bureau of Mines. Final data on the investigation were prepared under the direction of Edward F. Fitzhugh, Jr., chief Minneapolis Division, Mining Branch."

Jun 1, 1947

By Y. H. Cheng, D. M. Lewis, V. Castranova, M. W. Barger, J. K. H. Ma, J. Y. C. Ma, W. F. Xin

Bis-basic ethers off fluorene and fluoren-9-substituted derivatives such as tilorone have been reported to inhibit silica-induced fibrosis in rats. The potential antifibrotic potency of 2,7-bis (diethylamino) ethixy fluorine fluorenone (F-9-H.H), fluorenoxime (F-9-one), and fluorenol (F-9-ol) was F-9-axime > F-9-one ~ F-9-H,H > F-9-ol. Since the release of reactive oxygen species and growth factors from alveolar macrophages (AM) in response to silica exposure has been linked to the development of pulmonary fibrosis, the present study was carried out to determine the inhibitory effects of these compounds on rat AM activity in vitro. The following parameters were monitored: (1) cellular viability; (2) zymosan-induced respiratory burst activity (superoxide and hydrogen peroxide release, chemiluminescence, and oxygen consumption) of AM; (3) drug binding to AM; and (4) lipopolysaccharide (LPS)-stimulated interleukin- I (IL-1) release from AM. The bis-basic ethers, at 40 did not affect cell viability when incubated with AM for 30 min, but significantly inhibited zymosan-induced macrophage respiratory burst activity. The inhibitory effect of these agents was F-9-oxime > F-9-one ~F-9-H,H > F-9-ol. Binding of these drugs to AM was time and dose dependent, and exhibited the following binding affinity: F-9-oxime > F-9-one > F-9-H,H > F-9-ol. F-9- oxime was shown to inhibit LPS-stimulated IL-I release by AM in a dose-dependent manner. This inhibition of IL-1 release by AM cannot be explained as a decrease in viability. In addition, these drugs were also shown to impair human fibroblast proliferation in response to serum stimuli without impairing cell viability. These results indicate a positive correlation between drug binding to AM or other cell types and their inhibitory effects on cellular activities including oxygen consumption, superoxide release, hydrogen peroxide secretion, chemiluminescence, IL-I release, and proliferation. The ability of-these bis-basic ethers to modify AM and fibroblast functions in vitro suggests that further investigation of their reported antifibrotic potency in vivo is warranted.

Dec 1, 1996

By D. K. Deardorff

The hafnium-vanadium phase diagram was constructed within an estimated accuracy of ± 10° C and ± 2 wt pct composition. Alloys for investigation were melted under an atmosphere of purified helium by nonconsumable tungsten-electrode arc melting on a water-cooled copper hearth. Melting points were determined by optical pyrometer, and the remaining phase relationships were investigated by metallography, thermal analysis, and X-ray diffraction. The existence of a face-centered cubic intermetallic compound HfV2 (a = 7.38 A) was confirmed. A eutectic reaction occurred at 20 wt pct vanadium and 1,395° C to yield HfV2 and 8 solid solution. HfV2 melted incongruently by a peritectic reaction at 1,480° C, and the 3 solid solution decomposed eutectoidally at 1,165° C and 6 wt pct vanadium to yield HfV2 and a solid solution. The eutectoid, the eutectic, and the peritectic isotherms extended from 1 to 36.3 wt pct vanadium, from 8 to 36.3 wt pct vanadium, and from 26 to 89.5 wt pct vanadium, respectively. Terminal solid solubilities of hafnium in vanadium at 1,300° C and of vanadium in hafnium at 1,100° C determined to be about 3 and 1 wt pct, respectively.

Jan 1, 1965

By L. C. Karrick

The Bureau of Nines has received many inquiries on the subject of assaying oil-shales, both from individuals who desire to wake their own assay while in the field, and also from Commercial assayers and investigators. The present paper describes the assay retort used by the Bureau of Mines. in the research work on oil-shales now in progress at the Intermountain Experiment Station of the Bureau at Salt Lake City, Utah, and at the Colorado cooperative oil-shale laboratory, Boulder, Colorado. This retort, which was developed through experimentation in the bureau's laboratories, has been found to be convenient in use and. capable of yielding reproducible results. M. J. Gavin, Oil-Shale Technologist, gave valuable assistance in preparing the subject matter for publication and made many helpful suggestions during the experiments made by the writer in the course of the development of the assay retort. L. A. Anderson, research "fellow" University of Utah, assisted in the preliminary development of the assay retort.

Jan 1, 1921

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

By K. C. Dean

A semiquantitative test for the presence and identification of cesium and rubidium in rocks, clays, and mineral waters has been developed by the Bureau of Mines. The test can be used in the field, as a guide for the prospector, geologist, or mining engineer engaged in location or development [w]ork. It comprises two simple spot tests of a solution prepared from the [m]ineral sample. Phosphomolybdic acid, added to a drop of the test solution, [d]etects cesium, rubidium, and potassium in quantities as low as 60 parts per [m]illion. Silicomolybdic acid, added to a second drop of test solution, enables the operator to distinguish between cesium and/or rubidium and potassium. Test procedures, equipment requirements, and limitations of the method are described in this report. Cesium and rubidium were discovered in 1860 and 1861 by Bunsen and Kirchhoff with a spectroscope. The elements usually occur together, particularly in granite and granitic pegmatites. Rubidium does not occur as an essential constituent of any known mineral, yet it is found as a minor element in so many minerals that rubidium is 16th in abundance in the earth's crust. Cesium, which ranks as the 37th most abundant element, is the principal component of pollucite and a minor element in a wide variety of minerals.

Jan 1, 1960

By R. L. Grant

The Bureau of Mines applied automatic computational methods to analyze the degree of correlation between sound transmission and atmospheric conditions. Statistical analysis of data collected over a 5-month period indicated that the following weather variables, listed in order of decreasing importance) have a significant effect on the transmission of sound in the atmosphere: 1. Wind velocity and wind direction. Winds in the direction of travel of the sound wave increase the sound intensity and duration. 2. Barometric pressure. High pressures are related to low sound intensities and durations. 3. Atmospheric temperature. High temperatures are related to low sound intensities and durations. Inversion of the atmospheric temperature did not appear to affect sound transmission under the conditions of this study.

Jan 1, 1967

By Richard L. Jenkins

Systematic sampling, in reconnaissance fashion, of the continental shelves of the United States to define favorable areas of offshore mineral deposits, is one of the long-range marine mineral; programs of the U.S. Department of the Interior. In mid-1966 the Department of the Interior launched its Heavy Metals Program to stimulate domestic output of gold which is in serious short supply. The program is jointly conducted by the Geological Survey and the Bureau of Mines.

Jan 1, 1968

By H. S. Caldwell

This report describes work by the Bureau of Mines on the vacuum distilla¬tion of some of the more volatile metals such as cadmium, zinc, and magnesium from lead and tin. Evacuation within a distillation apparatus allows rapid diffusion of vapor away from the evaporation surface and prevents reaction of the vapor with residual gases. A reduction of pressure to several tenths of a millimeter makes possible practicable distillation rates, at temperatures for which the partial pressure of the metal vapor exceeds 10-3 atmosphere. The rate and selectivity of distillation depend primarily on the volatility and molal ratios of the alloy metals, and their chemical activity to each other. For very rapid evaporation or low concentration of the more volatile constituent, the rate is determined by the rate of diffusion of the evaporating metal, to the surface of the melt. Cadmium, zinc, magnesium, and tellurium were found to volatilize readily from both lead and tin. Tellurium appears to volatilize as an intermetallic compound rather than the pure metal. Antimony could not be removed from lead at 1,000° C.; the condensate was nearly all lead. Antimony, bismuth, and lead were removed from tin.

Jan 1, 1960

By Charles W. Huggins

Knoop hardness indentations were studied and measured with the electron microscope on TiB2, HfC, and A1B12 crystals. A detailed description of replicating the indentations using collodion and Faxfilm is made. A John Hopkins grating having 28,800 lines per inch was used to accurately determine the magnification used on the electron microscope. The primary objectives were to prepare carbon replicas of hardness indentations, to measure the indenations accurately, and to compare the results with those obtained with the light microscope. The resulting data showed excellent agreement between the measurements made on the replicas with the electron microscope and those made with the optical microscope. The replicas made from collodion showed slightly better agreement with the light optical values than did the replicas made from Faxfilm.

Jan 1, 1963

By Paul W. Jeran

Subsidence was monitored by the U.S. Bureau of Mines over the ends of longwall panels operating in the Pittsburgh, Kittanning, and No. 2 Gas Coalbeds of the northern Appalachian Coal Basin. The final subsidence over the finishing ends of three panels in the Pittsburgh Coalbed are compared with the subsidence measured over the rib at these panels. The characteristics of subsidence are different. At Mine A, data over the start of a longwall panel shows similar characteristics to the subsidence measured over the rib. Subsidence over the fmishing ends of panels in the Kittanning and No.2 Gas Coalbeds are also different from the subsidence over the rib. The use of a subsidence prediction model based on data gathered over the rib of a panel will not yield accurate results if it is applied to the finishing end of a longwall panel. Acceptable results may be obtained along the centerline over the starting end of a panel.

Jan 1, 1991

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.