Search Documents

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985

By Wilber Duvall, Leonard Obert

"INTRODUCTION This report is the first of four to be presented on the microseismic method 4/ of predicting rock failure in underground mining. The application of the microseismic method to one specific case, namely, that of predicting rock bursts in deep mining, has been described in two previous reports. 5/ 6/ Since the publication of these reports 5/ 6/ the method has been extended to other fields of mining, end it is the purpose of this report (Part I) to describe the general microseismic method, giving the empirical facts upon it is based, the different testing procedures, the method of recording and analzing the data, and the interpretations that can be obtained there-from. Part II will describe a series of laboratory experiments that were performed to give information on the origin of microceismims and the microseismic properties of various rocks. Part III will cover application of the method to specific mining problems together with a brief description of a number of investigations performed during, the last three years. Part IV will describe in detail the microseicmic equipment used in the various phases of these investigations."

Feb 1, 1945

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By Thomas M. Barczak

he stiffness characteristics of longwall shields were investigated in this Bureau of Mines study. Since longwall strata activity is characterized by roof-to-floor and face-to-waste displacements, a model with two degrees of freedom was used to describe the load-displacement relationship of the shield structure. The model considers the support as an elastic body and relates horizontal and vertical resultant forces acting on the support to associated displacements as a function of the stiffness of the support structure. Stiffness coefficients under full canopy and base contact configurations were determined by controlled displacement loading of longwall shields in the Bureau's Mine Roof Simulator (MRS). Three two-legged longwall shields of different manufacture were investigated. The stiffness characteristics of these shields were evaluated relative to two parameters, namely, shield height and setting pressure. The test results indicate a reduction in shield stiffness for increasing height. Setting pressure was found to have less of an effect on shield stiffness, producing only a slight increase in stiffness as setting pressure increased. Similar trends were observed for all three shields, indicating a similarity in stiffness characteristics for shields of the same basic configuration.

Jan 1, 1988

By Michael R. Yenchek

Contacts with energized conductors are a major cause of electrocutions in underground coal mines. Sensitive ground fault interrupters (GFI's) installed on in-mine three-phase ac utilization circuits would probably prevent the majority of these deaths. A sensitive GFI is a protective device that detects and interrupts small deadly ground currents in the milliampere range before those currents can cause ventricular fibrillation in humans. Commercially available three-phase sensitive GFI's have not been specifically designed for application in coal mines. The Bureau of Mines therefore tested three commercial GFI models to determine their worthiness for mine power systems. GFI design and construction, transient immunity, reliability, and time-current characteristics were evaluated in laboratory tests. No commercial device was found suitable for mine use without design modifications. The tests results will serve as a basis for the development of a mineworthy sensitive GFI in ongoing Bureau research.

Jan 1, 1985

By Robert J. Anderso

Few elements have received more attention and developed greater interest in the last ten years than titanium. The substantially pure metal has been din...ie. cult to isolate, and so far has been little employed oommercially, but the use af alloys and chemical compounds of titanium has increased markedly in recent years. The earlier attempts at preparing pure titanium resulted in various impure forme which, from their metallic appearance, were always mistaken for the metal. Hunter in 1910 isolated pure titanium by the reduction of titanium tetrachloride with sodium. This brief statement is issued by the Bureau of Mines in response to numerous inquiries which have been received concerning titanium. More complete in. formation on the metal may be had by consulting the referenpes appended. The Literature is voluminous and only the more important references are Riven. It has been drawn upon freely in preparing this report; also information was supplied by M. g. Hunter, Arthur Braid, M 1. Schmid, C. M. Johnson, N. B. Hoffman, and de Courny Browne. The pioneer investigator in titanium is A. IL Rossi.

Oct 1, 1922

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By F. W. Hoertel

Tungsten from the hydrogen reduction of WF was vapor - deposited to coat MERM (Material Evaluation Rocket Motor ) graphite and rhenium- lined graphite nozzles . These nozzles have surface configurations that preclude the conventional fabrication of high- density- tungsten liners . Operation at 550 ° C produced selectively placed uniform coatings of specified thicknesses at near theoretical density . An acceptable coating could not be deposited on a beryllia nozzle because of an undesirable side reaction between the substrate and one or more of the products of the reduction reaction .

Jan 1, 1964

By Robert J. Hundhausen, GEORGE M. GRISMER

This circular describes the methods and costs of deepening the Silver Summit three-compartment shaft in the Coeur d'Alene mining region of Idaho. A noteworthy rate of advance was achieved at this operation by the successful use of a mechanical shaft-mucking machine. The Silver Summit mine is 1 mile west from the town of Osburn, Idaho, via U. S. Highway 10. The adit-level portal of the mine is on the south slope of the Coeur d'Alene River Valley at an altitude of 2,700 feet. The Silver Summit shaft is 6,000 feet from the portal. In past years this shaft had been sunk from the adit level to a depth of 1,500 feet. During 1946 the Polaris Mining Co, deepened it to 3,095 feet. The work was done under a co- operative development agreement between the Silver Summit Mining Co. and the Polaris Mining Co.

Jan 1, 1948

By Thomas R. Bur

The strain and pressure gage methods for evaluating the relative performance of explosives in rock were compared. This comparison was based on a study of the responses of strain and pressure gages to explosion-generated seismic waves. Several explosives) representing a wide range of detonation pressures) were used. In general the relative performance of these explosives) as determined from amplitude) impulse parameter) and energy parameter measurements) is the same if the compressive portion of the strain pulse and the comparable portion of the pressure pulse are considered. Other similarities and differences of the two methods are also discussed.

Jan 1, 1967

By Rolland L. Blake

The Bureau of Mines is concerned with extracting minerals from residual geothermal brines after their heat content and some demineralized water have been recovered. This literature study is based on a survey of the literature and discussions with individuals knowledgeable on various aspects of the subject. This report examines the potential of the domestic geothermal mineral resources, considers the technical problems involved, and outlines possible effects on the environment from reservoir fluid withdrawal and reinjection. Geothermal resources in the Western United States were extensively explored during the 1960's. Limited development operations included exploratory drilling and operating wells producing hot brine, separating steam for experimental electric power generation, and recovering minerals in solar evaporation ponds or in extraction plants. Interest in the recovery of minerals and salts from geothermal fluids waned because of corrosion and scaling problems and low or no market value of the mineral products. Most of these problems can be controlled with existing technology and careful planning of processes and equipment. Extracting geothermal minerals is technically feasible, but the problems of low or no market value for major mineral products, and insufficient amounts of more valuably major products, make mineral recovery uneconomical at present.

Jan 1, 1974

By Carl R. Peterson

Development of reliable, portable, low headroom, hard rock crushers would improve the efficiency of most currently operated conveyor systems and make it possible to bring conveyor haulage closer to the face, thus eliminating expensive rock rehandling procedures. A crusher that could be easily moved would permit the more widespread use of lower cost haulage systems, such as conveyors, to transport the ore out of the mine. Such crushers would be installed close to the working areas, resulting in an optium haul from the face to the dump location. A recent contract study by Rapidex, Inc., "Application Study of Portable Underground Hard Pock Crusher" (USBM Contract No. J0265006) provides a survey of industry needs in portable underground crushing, together with conclusions and concepts as to specifications and type of crusher required to serve the greatest number of operations. To fill this need a three phase program has been undertaken by the Bureau of Mines: Phase I - Design: Phase II - Construction and Testing, and Phase III - Production Underground Test. This report covers Phase I only, and includes the complete engineering design and specifications of the Rapidex Rotary Jaw Crusher conceived in the earlier "Applications Study". Also included are the design, construction, and testing of a quarter-scale functional model, utilizing three different types of rock and two different crusher feeder systems.

Jan 1, 1978

By T. E. Gray

This report describes preparation characteristics of the significant coalbeds in Marion County, W. Va., as determined by the Bureau of Mines. It is one in a series telling what coals are suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.4 million tons of coal was produced in Marion County, W. Va., in 1958, of which almost 6 million tons was cleaned mechanically in nine cleaning plants. All of the coal mechanically cleaned came from the Pittsburgh bed. The Bureau of Mines estimated that 1,578 million tons of recoverable coal remained in the county in beds 28 inches or more thick as of January 1, 1955.

Jan 1, 1960

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980

By D. Harrington

Although for many years considerable attention has been given to devising safe and efficient methods of using explosives, with some success, relatively little has been done to provide satisfactory storage facilities for them. This was known long before the present war began, but it was emphasized during the past 30 months? inspections of explosive magazines by employees of the Bureau of Mines in administration of the Federal Explosives Act of December 26, 1941. These inspections have revealed woeful in adequacy as well as definite hazards and the urgent need for obtaining better storage facilities either by remodeling old magazines or constructing ink new ones that would afford suitable protection for the contents against theft, fire, deterioration, and detonation. The purpose of this paper is to offer suggestions and to show by sketches and drawings some of the fundamental features of suitable magazines. Type of construction and available materials differ with different; localities, but the information herein contained can be applied to most magazines, whether already constructed or the construct: on of which is planned. It is hoped that this information will be helpful and will aid persons who are trying to provide suitable storage for explosives end detonators. It is also hoped that States and cities will be made aware of the unbelievable laxity practiced in storing explosives in the United States and will take some remedial action.

Jan 1, 1945

By K. O. Bennington

The thermodynamic properties of two manganese silicates, pyroxmangite and fowlerite (zincian rhodonite), were experimentally determined by the Bureau of Mines. The standard enthalpies of formation were determined by hydrofluoric acid (HF) solution calorimetry, the low-temperature heat capacities by adiabatic calorimetry, and the high-temperature heat capacities by differential scanning calorimetry over the range 322 to 1,372 K. Data for the standard enthalpy of formation (AH298), the derived standard entropy (S298), and the standard Gibbs energy of formation (AGf 298) are as follows: Pyroxmangite [(Mn0.9554Cao,0446)(Si03)J- AHf298 319.668±0.46 kcal/mol AH298 (from oxides)... -7.215±0.11 kcal/mol 5295 23.785±0.048 cal/(mol'K) AGf298 -301.190±7.96 kcal/mol Fowlerite [(Mno.7o3Zno.0884Ca0.2086)(Sio3)]--AHf298 ?... -329.914±0.419 kcal/mol AH298 (from oxides)... -8.400±0.104 kcal/mol 5598 21.949±0.059 cal/(mol-K) AGf298 -310.716±7.99 kcal/mol These experimentally determined values were combined with data from the literature to calculate the Gibbs energies and equilibrium constants of formation over the temperature range of the measurements. Standard enthalpies, Gibbs energies, and equilibrium constants of formation are given as a function of temperature from both the elements and the constituent oxides.

Jan 1, 1987

By Loren R. Anderson

This volume documents the use of the probabilistic slope stability program PROBISH. The probabilistic slope stability program is an interactive program and is essentially self-tutorial. It prompts the user for the required input data as it is needed, and allows the user to correct mistyped data before analysis is initiated. The program computes safety factor probable Width of failing and probability of failure for a given circular failure surface. Four example problems are included to illustrate its use.

Jan 1, 1982

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964