Search Documents

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By J. J. Demeter

A tube-wall reactor with a Raney nickel catalyst deposited on the outer wall of the tube by flame spraying is effective in the practically complete conversion of 3H2+1CO synthesis gas to a high-Btu gas (methane) at an hourly space velocity of 7,000 volumes of gas (NTP) per hour per volume of annular volume. Partially reacted synthesis gas containing an appreciable amount of methane can also be treated in this reactor to increase the heating value to over 900 Btu per cubic foot. Excellent heat removal through the metal wall to a coolant and temperature control were obtained. The heat transfer co-efficient from the catalyst to the coolant was about 275 Btu per hour per square foot per ° F. Synthesis tests were conducted with tubes 1.2 inches in ad by 6 inches long, and 1.3 inches in od by 36 inches long. When operating at a synthesis gas rate of 100 to 120 scfh per square foot of catalyst-coated tube, catalyst life was long enough to realize a catalyst cost for the raw Raney nickel alloy of about 0.3 cent per 1,000 cubic feet of pipeline gas (900 to 950 Btu per scf). Gas recycling at ratios of 1:1 to 3:1 was effective in increasing conversion and in extending the life of the catalyst to about 16 weeks. In cost and in operating characteristics the tube-wall reactor compares favorably with the fluidized-bed and hot-gas-recycle reactor systems for the synthesis of high-Btu gas from H2+CO.

Jan 1, 1967

By D. B. Dow

The study of oil production methods with reference to the amount of oil originally pressent in the oil-bearing, formations has developed the fact that-ordinary methods-of production remove only a part of the oil actually present. In fact, it is generally realized that when a field is abandoned more oil remains in the sand than has ever been removed. As a consequence of this realization, the petroleum engineer has devoted considerable tine in recent years in devising methods for increasing the percentage of recovery. His studies have indicated that in most cases the total production of a field is dependent upon the available gas rather than upon the available oil. Mien the gas in the sand is exhausted, oil production ceases even though there may be enormous quantities of oil remaining unrecovered. Consequently, any method of conserving the gas or increasing the supply of gas will increase the ultimate recovery from a field. The practice of producing oil under vacuum increases the effectiveness of the gas remaining in the sand, as well as furnishing more gas by evaporating the light fractions of the crude. Pumping ' compressed gas or air down selected wells of a lease has been found to increase the production of oil from the surrounding wells. Studies of oil and gas ratios have indicated that much of the available gas has been wasted as far as its effectiveness on oil production is concerned. his has led to the development of "stop cocking"3 and the practice of producing under back pressure3, which methods aim, to obtain more effective work from the gas with reference to the amount of oil delivered to the well.

Jan 1, 1926

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By L. C. IlsLey, E. J. Gleim

It is the firm belief of the Bureau's engineers that the introduction of electrical mining machines has done much to increase safety in mining as a whole . There can be no doubt but that the substitution of machine mining together with permissible powder for the method of " shooting from the solid " has been the means of saving the lives of many shot- firers . Machine mining also leaves the roof in a better condition as lighter charges of powder are required to bring down the coal . Thus the danger from falls of roof are lessened . It is recognized that every effort should be made to prevent all accidents due to the use of electrical machinery but it is felt that any action tending to limit the use of such machinery would be a backward rather than a forward step in the safety measures laid out to decrease the hazards in coal mining .

May 1, 1920

By G. B. Goodman, W. H. Pailes, P. D. Kaplan, I. Stachura, V. Castronova

"The risk of developing silicosis in underground coal miners, tunnel workers and some foundry workers is well-known. These persons generally develop the classic form of the disease over a prolonged period of time. Workers involved in abrasive blasting of bridges and those polishing tombstones have been reported to develop an acute form of silicosis within a few years of commencing exposure. Not well-appreciated is the potential for development of acute silicosis among drillers at surface coal mines. We report the case of a 33-year--old man who worked primarily at surf ace drilling, developed acute silicosis within three years of beginning exposure, and who initially responded dramatically to corticosteroid therapy. CASE REPORTThe patient is a 33-year-old white man who worked as a rock driller at a quarry and also at surface coal mines in western Pennsylvania since 1975. Prior to 1983, much of his work was done with a wet process in which water was applied to reduce dust generation. After 1983 he worked primarily as a driller at a surface coal mine using a dry process. He never wore a respirator. He described the dust as being so dense that he ""couldn't see anything.- In August 1986, he presented to his local physician with a complaint of pleuritic chest pain and shortness of breath. A chest x-ray film was obtained showing only a few p and q opacities. He continued working and these symptoms subsided, but the patient noted the onset of progressive weight loss. By May 1987, he had lost approximately 50 lb. In addition, he suffered profound malaise, dyspnea, migratory chest pain and arthralgia, fevers and drenching night sweats.A course of erythromycin therapy given in the hospital resulted in only fleeting improvement. Studies for Legionella and Mycoplasma infections were negative, as was a tuberculin skin test. The patient was transferred to Allegheny General Hospital in Pittsburgh on June 4, 1987.There was no history of serious medical illness, including tuber¬culosis. The patient admitted to smoking between I and 1 1/2 packages of cigarettes daily for 2 1/2 years prior to May 1987 when he stopped smoking. He denied intravenous drug abuse, homosexual activity or receiving transfusions of blood or blood products.On physical examination the patient was a thin, febrile white man who appeared chronically ill. Bilateral axillary and cervical lymphadenopathy was present. Chest examination showed restricted expansion and bilateral crackles. Examination of the heart and abdomen disclosed no abnormalities."

Mar 1, 1992

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

By E. C. Lane

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of samples of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 3162/4 is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By Will H. Coghill

This paper on milling methods and costs at a flat river (Mo.), mill is one of a series of information circulars on milling methods and costs which is being prepared by the United States Bureau of Mines, The mill under consideration treats 5,000 tons of load ore daily by table concentration and flotation. It is 25 years old, and yet it is a new mill. Research has been in continual progress at the plant since its beginning, and accordingly a day never passes without a record of change for advancement. The changes have been so orderly that no evidence of obsolete equipment remains.

Jan 1, 1932

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By W. P. Huleatt, Jr. Traver, Jr. Hazen

"Vanadium and uranium occur widely distributed throughout western Colorado and eastern Utah, and a few deposits have been found in northeastern Arizona and northwestern. New Mexico. The area in which it occurs includes approximately 10,000 square miles and is generally referred to as the vanadium region of Colorado and Utah.The majority of the deposits consist of replacement bodies and impregnations of rare minerals in the lower Morrison formation of Jurassic age. The ore bodies are flat, with irregular margins, and most of them conform to the stratification.The ""rim rock"" topography of the region includes many steep-walled canyons and plateaus, which afford an abundance of outcrops that have been responsible for most of the discoveries of mineralized areas. Delimitation of ore bodies within the areas is accomplished most effectively by core drilling from the surface.The deposits were discovered in 1899 and from 1911 to 1923 wore worked extensively for radioactive uranium ores, principally carnotite.The discovery and marketing of the richer and more cheaply mined pitch-blende ores of the Belgian Congo left the Colorado-Utah deposits without economic importance as sources of radium and uranium, and the region became inactive in 1923. After a period of comparative inactivity, the rising demand of the alloy-steel industry for vanadium renewed interest in the deposits, which were known to contain that metal. By 1938, vanadium production in the area had achieved respectable proportions, and new impetus was given to it by the United States’ entry into World War II in December 1941. In 1942, new treatment plants for vanadium ores were completed in Monticello, Utah, and Durango, Colo. In order to meet the requirements of these and other plants in the region, it became necessary to open new vanadium mines and prepare old onus for production.In an effort to stimulate mining, the Metals Reserve Company initiated a stock-piling program and appointed the united states Vanadium Corporation, to act as its purchasing agent.The extra production was expected to come largely from small, independent operators whose limited funds did not permit them to maintain development and exploratory programs. Study of conditions made it apparent that extensive exploration would be necessary to sustain production, and accordingly the Bureau of Mines initiated an exploratory drilling project on a cooperative basis with the Geological Survey. The principal objects of the work were to enlarge the known ore reserves of the area and, if possible, discover new ones. The results have been gratifying in both respects."

Sep 1, 1946

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of sample of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 31624/ is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By Albert L. Toenges

The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by: (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war material; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this Critical fuel situation, an investigation was made of possible sources of fuel nearer to points of consumption in New England.

Jan 1, 1948

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By William L. Crentz

Late in the nineteenth century en active coal-mining industry was begun in the Lower Freeport bed near Reynoldsville, Pa., where the bed thickened to more than 10 feet in places . The coal was readily accepted as an excellent steam fuel. Much of the thick coal his been depleted, but there are many areas where the deposit averages about 14 feet in thickness. As the more desirable mining sites were worked out in the Lower Freeport bed, other beds were exposed from which will come the county's major cowl production in future. The Lower Freeport bed is still the most important bed in Jefferson County from a production standpoint. The Lower Kittanning bed is second. Sporadic mining is being done in the Upper Freeport, Upper Kittanning, Middle Kittanning, Clarion, and Brookville beds. Strip mining has permitted recovery of much coal that could not be mined profitably by conventional underground methods.

Jan 1, 1953

The Department of Interior, U.S. Bureau of Mines performs the task of estimating the quantity of coal reserves existing in each state on a county by county basis. As a part of Information Circular 8655, the Bureau of Mines established the criteria for the uniform estimations of coal reserves and listed the most recent estimates of coal reserves by county and by seam. At the same time however, the Bureau recognized that these figures represented the upper bound with regard to the estimated actually usable or obtainable reserves. Recovery of these reserves are subject to the mining methods used and to the resolution of such problems as the use of poor quality coal and competition provided by conflicting land use. These problems, in practice restrict the recovery of the estimated quantities of coal reserves listed in IC 8655. Another impact, the subject of this manual, is the impact resulting from previous mining activities. In particular, many of the reserve seams included in the reserve estimates overlie or underlie mined-out coal beds. Portions of these reserve seams may therefore be unmineable or at best may have a reduced quantity of extractable coal. In order to improve the accuracy of the coal reserve base estimates, the Bureau of Mines funded an effort1 to develop a systematic methodology for estimating the coal loss associated with the impact of previous mining activity. The coal loss calculation model (CLCM) described in this manual is a result of that effort and addresses the percentage of coal loss in reserve seams due to previous overmining or undermining.

Jan 1, 1976

By Harold J. Barnett

In January 1948 , the Secretary of the Interior directed that a study be made of energy resources and requirements that would provide a basis for continuing appraisal of the adequacy of the Department's programs in the energy field . That this instruction was timely has been demonstrated by the increasing interest being evidenced by Congress , industry , labor , and the public in the future of the energy segment of our national economy . Several studies of individual energy sectors have appeared . Various legislative proposals have been made in Congress for obtaining more information on this subject . Substantial interest in energy projections is not , of course , a recent innovation . Energy availability and consumption are strategic factors in peacetime prosperity and growth and in our national defense as well . The past generation's literature of earnest public discussion and of legislative consideration of matters involving energy projections is very extensive . This is an exploratory study produced in the Program Staff of the Office of the Secretary of the Interior in the first half of 1949 and revised recently to take account of certain of the preliminary energy data from the 1947 Census of Manufactures and critical comments . It is offered at this time solely as a technical contribution in economic research technique . As the Bureau of Mines has recently undertaken to revise this preliminary study , critical and other comments are invited .

Oct 1, 1950

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943