Search Documents

By B. B. Letson

The heats of formation of lithium chloride and lithium oxalate were determined with the aid of a Bureau-developed, glass Dewar-type solution calorimeter which uses thermistors as its temperature sensing element. Values obtained at 298.15° K were -98.38 ± 0.54 kcal/mole for lithium chloride and -329.02 ± 0.79 kcal/mole for lithium oxalate, using graphite as the standard state for carbon.

Jan 1, 1965

By M. M. Jones

Natural brines are potential domestic resources of minerals. The brines of Searles Lake, CA, for example, contain an estimated one-fourth of our current reserve of tungsten. A key to Bureau of Mines research to recover this critical mineral is the ability to quantitatively measure concentrations of particular constituents in the large number of brine samples and process solutions produced under a multiplicity of test conditions. This paper describes procedures used to determine arsenic, boron, phosphorus, silicon, and tungsten in these solutions by simultaneous inductively coupled plasma spectrometry. A variable in-ternal standard method was used to compensate for tungsten interference on the other analytes in tungsten concentrates, and matching standards were used to determine tungsten in raw brine. Other solutions were analyzed using normal techniques. Analytes were determined down to 1 mg/L with an average precision of 2.5 pet relative standard deviation. Accuracy, estimated using synthetic solutions and by comparison with values obtained by other methods, averaged about 2.5 pet. The methods were rapid, required little sample preparation, and provided the needed sensitivity.

Jan 1, 1985

By D. Harrington

Coal mines and mining-, as well as metal and nonmetallic mines and min¬ing, are not inherently unsafe, although mining people think they are and would like to have everyone else think so. It is now being demonstrated that mines can be operated with essentially as much safety as any other major industrial enterprise; but most mining people, including workers as well as officials, have been slow to realize or admit this. In the past, and with most people even at present, the idea has prevailed that it is utterly impossible to operate a mine without accidents. Although, as in all other kinds of industrial activity, it is true that some injury is likely on occasion to occur to some workers and an extraordinary accident may occur to one or more persons under exceptional conditions, mines can be operated with few if any accidents if a reasonable amount of the right kind of precautionary effort is exerted and kept in effect.

Jan 1, 1934

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By G. E. McClelland

The Bureau of Mines investigated chemical methods for producing high- purity gold from precious-metal-bearing zinc precipitates and steel wool cathodes. Precious-metal-bearing zinc precipitates and steel wool cathodes are unrefined products from conventional cyanidation and heap leaching-cyanidation operations. The zinc precipitates contained 14,40 pct Au and 0.35 pct Ag. The precious-metal-bearing steel wool cathodes contained 20.65 pct Au and 4.84 pct Ag. The precipitates and cathodes were treated with dilute acid to solubilize the silver and/or base metals. The gold-bearing residue was leached in dilute aqua reqia to solubilize the gold. High-purity gold was precipitated from the aqua regia solution with oxalic acid, sulfurous acid, sodium bisulfite, and gaseous sulfur dioxide. The leaching-precipitation experiments recovered 99.9 pct of the gold. The gold precipitates ranged in fineness from 997 to 999 fine. The chemical refining method provides a viable technique for the smaller operator to produce high-purity gold without using pyrometallurgical refining methods.

Jan 1, 1985

By M. M. Tilman

As part of ongoing research to improve mine safety, the Bureau of Mines conducted research on the corrosion of friction rock stabilizer steels in five Missouri lead and iron mine waters. Electrochemical corrosion tests, including evaluation of pitting tendency, were performed on two types of high-strength, low-alloy (HSLA) steels and galvanized steel in four Missouri lead mine waters and one Missouri iron mine water. The tests were conducted at in-mine water temperatures in both air-saturated and deaerated waters. Static, weight-loss corrosion tests were also conducted on HSLA steel specimens in the five Missouri mine waters for 2,900-h duration at average in-mine water temperatures and air-dissolved oxygen contents of 6 to 7 ppm. Corrosion rates determined by the weight-loss tests were roughly comparable with rates determined electrochemically in deaerated waters containing 0.3 to 0.5 ppm dissolved oxygen content. Passivation of specimen (nongalvanized) surfaces in air-saturated waters resulted in very low electrochemically deter- mined corrosion rates. Pitting-tendency was generally higher for both HSLA steels in air-saturated waters than in deaerated waters. Galvanized steel generally exhibited higher tendency to pitting in the deaerated waters than in the aerated mine waters.

Jan 1, 1985

By John J. Sammarco

The functional safety of programmable electronic (PE) mining systems is an international issue and concern. From 1995 to 2001, 11 PE-related mining incidents in the U.S. were reported by the Mine Safety and Health Administration (MSHA); 71 PE-related mining incidents were reported in Australia. MSHA does not have regulations for formal evaluations of the functional safety of PE mining systems. Hence, the National Institute for Occupational Safety and Health (NIOSH), in partnership with MSHA and the industry, generated the NIOSH safety framework for functional safety of PE mining systems. An overview of the NIOSH framework is given; the key framework elements, the safety life cycle and safety integrity levels are detailed. The safety framework approach has impacted the national and Australian mining industries by enabling the industries to advance from an ad-hoc approach to a formalized and systematic functional safety process. In retrospect, valuable lessons were learned for addressing functional safety and for changing industry perspectives and practices. These lessons continue to benefit mining and are applicable to other industries as well.

By Bernard Porter

The rate of the heterogeneous reaction between high-purity uranium metal and uranium tetrafluoride in molten lithium fluoride was measured. The apparent heat of activation for the reaction is 16.91 kilocalories per mole of UF4. A surface-controlled mechanism is suggested in which UF4 is adsorbed on the uranium metal surface. Additional UF4 reacts with the adsorbed species and the metal site to form an activated complex that decomposes to the product UF3. The reaction is an important source of metal loss in the electrowinning of uranium metal.

Jan 1, 1966

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might perhaps, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this distinction in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Camp Brothers Company, Mogadore, Summit County, Ohio.

Jan 1, 1936

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

By Barry Beith

This report details a study which was designed to assess the effect of retroreflective material on detection and form recognition of workers in the mining environment. Further, the study attempted to determine an optimal configuration of retroreflective material with respect to amount and placement on the body to facilitate detection and form recognition. The study involved a one-fifth scale simulation of the perceptual task found in the underground low seam coal mine. Four different configurations of reflective material were presented in various body positions, common to low coal miners, at three different locations in the visual field, i.e., 10, 25, and 45 degrees from focal line-of-sight. All reflective configurations significantly improve detection and form recognition over configuration (cap only) worn by miners. As the amount of reflective material increased, accuracy also tended to increase. Based on the configurations investigated by this study, the Armband configuration (i.e., refectorized armbands, belt, self-rescuer and battery pack) was determined to be optimum. It is recommended that an actual field evaluation be made using the Armband configuration to establish if simulator results are generalizable to the underground mining environment.

Jan 1, 1980

By Benjamin W. Haynes

This research was conducted as part of the U.S. Department of the Interior, Bureau of Mines program to recover metals, glass, and a combustible fraction from municipal solid waste (MSW). The objective of this analytical study was to determine the concentration of antimony, arsenic, and mercury in samples taken from various sampling areas in the Bureau of Mines raw refuse recycling plant and to compare these values with those for coals used in the generation of electricity. To provide the necessary analytical data, sensitive reproducible ashing-chemical digestion-atomic absorption procedures were adapted from published procedures. It was determined that antimony and mercury concentrations in the combustible fraction of MSW are approximately an order of magnitude higher than those found in coals presently used for power generation;' the arsenic concentration is similar in both fuels.

Jan 1, 1978

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

By Robert Howard

With the rapid depletion of the Peerless Coal Co.'s mine in Spring Canyon, it was necessary, if the company was to remain in the coal-producing business, to look to the development of a new property or to acquire a mine already developed. After careful investigation of several operating properties it was decided by the officials of the company to take over the lease on an undeveloped acreage held by a private party in Price Canyon, about 3 miles north of Castle Gate, Utah.

Jan 1, 1930

By Welby Courtney

Because of the inherent safety problem associated with the deposition of airborne respirable dust onto the floor and other airway surfaces, the Bureau of Mines investigated the rate of reduction of airborne respirable dust in an airway due to deposition of the particles onto the surfaces of the airway. The effects of relative humidity and air velocity on the deposition rate were examined. It was found that the deposition rate was comparable in magnitude with the Stokes sedimentation rate and that it was independent of relative humidity. However, near the dust source the deposition rate depended significantly upon the air velocity, with such dependence decreasing with increasing distance from the dust source. In addition, the size distribution of the airborne particles was approximately constant along the first 300 ft of the airway, indicating that it was not merely the larger (heavier) particles that were being deposited. These results suggest that deposition, though comparable with the Stokes sedimentation rate in magnitude, does not follow a simple Stokes-type process, and that the process of deposition remains to be explained.

Jan 1, 1986

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967

By A. J. Barry

To determine the torque-load relationship for SIB-inch (nominal)-diameter roof bolts, the Bureau of Mines tested 5 makes of expansion shells and 2 types of bolts (regular and high-strength) in 2 sandstone and 2 shale mine roofs. Unused flat-steel bearing plates in as-received condition were used in these tests. The relationship between torque and load was found to be approximately 50 pounds of load per foot-pound of torque for both the regular and high-strength bolts. This relationship is valid up to 130 foot-pounds for the regular bolts and up to 175 foot-pounds for the high-strength bolts. A torque of 130 foot-pounds on a regular bolt will produce a load of 6,150 ± 1,910 pounds 90 percent of the time, and a torque of 175 foot-pounds on a high-strength bolt will produce 8,050 ± 2,750 pounds 90 percent of the time. Above these values, the torque-load relationship tends to be erratic due to binding between the bolt and plug threads. Binding causes excessive torque to be expended in producing torsion in the bolt rather than tension. This torsion adversely affects the yield load of the bolt. Therefore, the installed torques should not exceed the 130-and l75-foot-pound values. A statistical analysis of the data showed that the torque-load relationship was not significantly affected by the type of bolt or expansion shell unit but might have been affected by the type of rock.

Jan 1, 1956

The Bureau of Mines, U.S. Department of the Interior, devised a flotation technique for upgrading chromite in chromium ores and gravity concentrates. The technique consisted of cationic flotation of chromite from a slime-free pulp acidified to pH 2.5 or lower using H2S04 modifier. Flotation results showed that ore containing serpentine as the primary gangue mineral was more amenable to concentration by this technique than ore containing the readily floatable olivine as the primary gangue mineral. Rougher flotation of a chromite ore containing abundant serpertine increased the grade form 19 to 41 percent Cra03 at a chromite recovery of 89.6 percent. Rougher flotation of ore containing abundant olivine upgraded the chromite from 23.4 to 29.6 percent Cr203 at a recovery of 89.4 percent. The technique was also applied to chromite gravity concentrates to further upgrade chromite and to reject silicates. Flotation of a gravity concentrate containing 40.9 percent Cr203 and 4.4 percent SiO2 recovered 90 percent of the chromite in cleaner products containing 44.9 percent Cr203 and 0.63 percent Si02. The combined recovery by gravity and flotation was 87 percent. An economic evaluation of this technique will be undertaken to deter-mine its feasibility for commercial use.

Jan 1, 1980

By M. F. Chambers

The U.S. Bureau of Mines conducted experiments on electrowinning of neodymium metal by using a molten-metal cathode at 650° C and an electrolyte of 50 mol pct NdCl3 (neodymium chloride) and 50 mol pct KCI (potassium chloride). The molten-metal cathodes were alloys of magnesium and zinc or magnesium and cadmium. Current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode; The Mg-Cd cathode was easily separated from the electrolyte. In contrast, the Mg-Zn cathode tended to mix with the electrolyte, making separation difficult. The cathode metals were separated from the neodymium by distillation at 1,100° C under a vacuum of 10-3 torr. Neodymium metal of 99.9+ purity was recovered from the Mg-Cd alloy cathode after 30 min distillation time. The neodymium recovered from the Mg-Zn system contained almost 2 pct Zn after vacuum distillation. Continuous operation using the Mg-Cd alloy cathode was demonstrated.

Jan 1, 2010