Search Documents

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By David C. Oyler

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbed at a vertical depth of 999 feet. The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a "bird foot" pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to 130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By William J. Campbell

This Bureau of Mines report describes a study conducted to determine the relationship of mineral habit to particle size and shape characteristics for prismatic, acicular, fibrous, and asbestiform varieties of tremolite. Particle measurements were made with the petrographic microscope at X 1,250 and the scanning electron microscope at magnifications up to X 10,000. All of the varieties of tremolite, upon Wiley milling, produced a significant percentage of particles that meet the Federal regulatory criteria for counting as asbestos fibers. However, only the asbestiform variety gave milled particles that fell into a size range of >10 µm in length and <0.5 µm in width; some medical scientists consider this range significant for production of adverse health effects.

Jan 1, 1979

By D. Harrington

We Americans pride ourselves that ours is the greatest, most advanced and most civilized nation in the world, yet statistics indicate that apparently we have little appreciation for the lives and limbs of the people whose efforts give us whatever greatness we possess. The latest available statistics indicate that the annual accident death rate per 100,000 of population is nearly 80 or far higher than that of any other country in the world except Chile; is more than double the rate in Hungary, Netherlands, Ireland, Belgium, Denmark, Italy, Germany, Norway, Sweden, and Finland; is nearly double that of England, Wales, the Union of South Africa, New Zealand, Japan, Australia, and Scotland; and is 25 to 40 percent greater than Switzerland, France and Canada. To make matters worse, from the viewpoint of mining; the latest available statistics give mining by all adds the worst accident rate of the major industrial occupations in the United States, the accident severity rate for mining in 1935 being listed by the National Safety Council as 10.14, the next highest rate being 4.52 for construction, and the average rate for 30 main industries being 1.58. IMPROVEMENT IN SAFETY RECORDS Offsetting to a slight extent this rather dark picture is the fact that starting about 1930 the mine-accident rate in both coal and metal mining began to fall, reaching an all-time "low" in metal mining in 1932 and in coal mining in 1933. It now appears probable that the year 1936 has again lowered the accident rate in coal mining and this, together with the fact that the years 1933, 1934, 193 5, and 1936 all set much lover accident rates in coal mining than ware achieved for any similar previous period, gives hope that the trend is definitely in the right direction, though from the above figures mine-accident severity has a long, tedious road to travel before it becomes as low as the severity rate of all other major industries in the United States.

Jan 1, 1937

By Leonard Obert

A triaxial procedure is described for measuring the modulus of elasticity and Possion's ratio of stress relief cores , that is , the concentric hole cores obtained by the overcoring technique . The elastic constant determinations can be made at stress levels comparable with those encountered in underground mining . The results from tests on an aluminum alloy calibration specimen and four rock specimens are included .

Jan 1, 1964

By Elton L. Litchfield, Milton L. Weiss

Studies were made on the projectile impact sensitivity of explosives by subjecting explosive samples to the impact of metal projectiles fired from a 0.50- caliber gun . The projectiles , in the form of right cylinders , made plane surface to plane surface contact with the explosives . Pressures in the explosive were investigated with an expendable pressure transducer in some instances . The physical model of the projectile - explosive interaction describes , in principle , the duration of the peak shock pressure in terms of the projectile and explosive geometry and the steady- state penetration of the explosive . Of the explosives studied , liquid hydrogen- solid oxygen and liquid oxygen - solid or liquid hydrocarbon fuel were the most shock sensitive ( requiring an initiating shock of about 1.0 kb or 987 atmospheres pressure ) ; cast TNT was the least sensitive ( requiring an initiating shock of more than 110 kb pressure ) . Measurements of pressure in the explosive showed some moderate space resolution by the transducer and gave pressure distributions in agreement with expectations from the model of the shock processes . The appearance of the recovered projectiles and the calculated initiation shock pressures suggest that the solid explosives were initiated directly to high- order detonation , whereas the liquid explosives were probably initiated to low- order detonation-- with a subsequent , later transition to high- order detonation .

Jan 1, 1965

By M. R. Geer, H. F. Yancey

Fuel requirements of the Pacific Northwest have been increased greatly by the war . To the normal peacetime demands for fuel have been added the requirements of new industrial and metallurgical plants engaged in war production , the increased demand arising from expansion of existing industrial establishments , increased amounts of railroad fuel required to handle wartime traffic , and increased quantities of domestic fuel required by the influx of war workers . In the face of these augmented demands for fuel shipments of fuel oil have been curtailed , wood fuel which normally is an important factor in both industrial and domestic markets of the area is less abundant , and the production of coal in Washington has decreased sharply . The fuel requirements of the region have been met so far by shipping large tonnages of coal into the Pacific Northwest from Utah , Wyoming , Montana , and Colorado ; the quantity received from these States and Canada in 1943 amounted to 2,688,9124/ tons , 175 percent of the Washington production . or The proximity of the Washington coal mines to large centers of war production has resulted in widespread migration of miners to employment in shipyards and aircraft plants ; the ensuing shortage of miners largely accounts for the decreased production of coal in the State . Hence , strip mining , which requires relatively few workers and a shorter time for development , offers an attractive means of alleviating the local coal shortage and obviating the necessity of shipping coal from the producing areas of the Rocky Mountain States to the Pacific.coast . So urgent has been the necessity for augmenting local coal production that any coal property that promises to be amenable to strip mining , even though the coal may be inferior in quality , has warranted examination . Even low- grade coals that cannot compete in the normal market can be used locally , thus releasing better coals for shipment to critical centers. of consumption ... One such deposit of low- rank fuel examined by the Bureau of Mines is in western Lewis County , about 9 miles east of Toledo , Wash . The coal is lignitic and on the as - received basis has a heating value of 6,000 to 6,500 B.t.u. per pound . The property is of interest primarily because the physical conditions favor operation by stripping and offer opportunities for low- cost production with very low manpower requirement .

Jan 1, 1945

By M. M. Tilman

The purpose of this investigation was to determine the effects of small amounts of cobalt in nickel on the tensile properties and hardness of representative types of austenitic stainless steels . Cobalt substitutions for nickel up to 2 weight - percent were made in types 302 and 309 stainless steels . Data were obtained at room temperature for tensile strength , yield strength , percentage elongation , percentage reduction in area , and hardness . In type 302 steels , tensile strength and hardness increased with increased percentages of cobalt , percentage elongation and reduction in area decreased , and yield strength showed little change . Property changes were largely due to the reduction of nickel content rather than to the addition of cobalt . In type 309 steels , only minor variations were observed for the properties investigated ; the effects of the relatively snall cobalt substitutions and nickel reductions were somewhat reduced by the higher total alloy content .

Jan 1, 1964

By R. W. METCALF, A. G. Charles, F. M. SHORE

To furnish the information frequently requested by producers and suppliers as to the fuel requirements of the Federal Government , the Bureau of Mines , with the cooperation of the consuming departments and establishments , has collected the data herein , showing the Government's fuel consumption during the fiscal year ended June 30 , 1930. The following tables show the quantities and kinds of fuels consumed by the Federal Government in each of its departments and their principal branches , in each State , and in Alaska , Hawaii , Panama Canal Zone , Porto Rico , and the Virgin Islands . The separate departments and establishments were asked to supply information for each Federal building or other plant and , as to vessel fuel , the amount loaded at each port of supply . Fuels consumed in internal combustion engines are not included . The report does not include fuels used by Post Offices of the fourth class , since their fuels are not purchased by the Federal Government but are covered by an allowance in each case for light and heat . In some cases the data supplied represent receipts , which are approximately equivalent to consumption . The present study is believed to be the first effort to bring together the data representing the Government's requirements for the various fuels which it consumes . Figures showing the coal consumed by the Federal Government were gathered for the year 1922. These data are shown in an article by O. P. Hood and R. H. Kudlich of the Bureau of Mines , contributed as a chapter to " Industrial Coal ; Purchase , Delivery and Storage , " published by the American Engineering Council . The figures of coal consumption presented herewith are approximately comparable with those published for 1922 , a relatively small difference being due to the fact that the 1922 figures include the Philippine Islands and all other territory in which any coal was consumed by the Government . At the present time , the only data on Government fuel consumption that are published regularly are those compiled by E. B. Swanson , chief economist of the petroleum economics division of the Bureau of Mines . These are published annually by the Bureau of Mines in " Sources and Distribution of Major Petroleum Products , Atlantic Coast States , " and by the bureau in cooperation with the American Petroleum Institute in the annual " National Survey of Fuel Oil Distribution . " It is believed that the data herewith will prove of interest and value to the fuel industries as well as to Government consumers and that it will also afford a basis for measuring future trends in the use of the various fuels by the Federal Government . Figures showing the quantities of the various kinds of fuels consumed by each of the executive departments and independent establishments , are given in Table 1. It should be noted that when one organization procures and delivers fuel to be consumed by other branches

Apr 1, 1932

Norton Co., a manufacturer of abrasive products and diamond drilling and coring bits for oil and gas exploration, is building a $19.1 million addition, scheduled for completion in late 1980, to the Huntsville, AL. The plant makes alumina-zirconia abrasive grains used in grinding wheels and coated abrasives. ALUMINUM Martin Marietta Aluminum Inc. announced plans to expand production capacity of its 112,000-ton-per-year primary aluminum smelter at Goldendale, WA to 177,000 tons per year. The $125 million expansion was scheduled to come onstream in 1981. The Aluminum Company of America announced plans to restart a fourth potline during October at its 185,000-ton-per-year Point Comfort, TX primary aluminum smelter.

Jan 1, 1979

By James C. Barker

In 1981 and 1985-1986, the Bureau of Mines conducted orientation studies of marine placer platinum-group metals (PGM). PGM are derived from the Goodnews Bay ultramafic complex and magnetic surveys show that the complex extends offshore at least four mi. The present seafloor was an emergent foreland as recently as 8000 years ago. High-energy ocean processes are transporting and depositing sediment such that PGM-bearing materials are reworked and later masked by barren littoral drift. Exploration targets include 1) placers formed since present transgression began, and 2) ancient marine and drowned fluvial deposits. Additionally, there is evidence of PGM solution transport and accretion. At least minor values of PGM in Recent lag-type placers and possible submarine strands are concentrated along an offshore scarp incised through glacial deposits into the preglacial surface between Flat Cape and Red Mountain. Other Recent PGM-bearing features include Flat Cape shoal, Chagvan Bay, Salmon River delta, and modern beaches. Ancient placers include possible N-S fluvial systems 2 to 3 mi offshore, a nearshore scarp 50 ft below sea level, and strands adjacent to projected ultramafic bedrock slopes. The existance of ancient placers is dependent on depth of glacial erosion. SEM studies show PGM are principally isoferroplatinum and osmiridium, with minor sperrylite, moncheite, and platiniridium. Gold is a co-product, and concentrates comprise chromite, ilmenite, and magnetite. Beneficiation tests successfully concentrated precious metals from natural blacksand accumulations, but failed to concentrate low-grade lag gravels.

Jan 1, 2011

According to reports in August, Botswana RST&apos;s copper- nickel-cobalt smelter at Selebi-Pikwe produced 7 percent above the rated capacity of about 3,500 metric tons of matte per month. This record production occurred after 2 years of plant production difficulties and was brought about by a new management team. A shutdown for furnace maintenance had been planned for this year, but was postponed because of the improvements in production and operations. However, the mining operation continued to face problems relating to higher costs and some outstanding claims. COPPER: Effective December 1, ASARCO, Inc. and Phelps Dodge Corp. reduced their domestic copper prices by 54 per pound. Within a period of 3 days, a11 other producers (Kennecott Copper Corp., Newmont Mining Corp., Cities Service Co. , Copper Range Co. , Duval Corp., and Inspiration Consolidated Copper Go. ) had either lowered or discounted their market postings by 5¢ to 65.625¢ per pound on electrolytic wirebar and 65$ on cathode plate. Between November 29 and December 3, New York merchants decreased wirebar quotations by 1.8¢-2¢ to within a range of 57.8¢-58¢ per pound. New York Commodity Exchange (COMEX) spot-contracted copper in the week was priced at 57. 1¢ on Monday, 56.7¢ on Wednesday and Thursday, and 57.4¢ on Friday, resulting in a 5-day average of 56.9¢, London Metal Exchange (LME) cash (prompt) wirebar averaged 56.3¢ last week, opening Monday at 56.6¢, falling from Tuesday?s high of 57.2¢ to Wednesday?s low of 55.6¢ and closing Friday at 56.1¢. Foreign producers, guided by LME market transactions, lowered wirebar quotes to 56¢ per pound. Copper stocks as of December 3 totaled 187,702 short tons at COMEX warehouses and 654,573 tons at LME depositories, compared to 97,413 and 537,481 tons, respectively, for the corresponding 1975 period.

Jan 1, 1976

By E. D. Gardner

Oil shale, a long-considered potential source of motor fuel in the United States, is found over an extensive area in the Green River formation in Colorado, Utah, and Wyoming.4/ Oil has been retorted commercially from shale in Scotland for many years,5/ and work done by the Bureau of Mines and other investigators has shown that it is technically feasible to extract oil from American shales.6/ By refining, the shale oil may be converted into marketable products similar to those manufactured from crude petroleum. The present paper, which was finished in 1936, discusses methods that would be adaptable to mining certain American shales, and the treatment applies specifically to conditions iii the Green River formation on Naval

Jan 1, 1942

By R. H. Schutz

This publication lists the respiratory protective devices approved by the Bureau of Mines as of December 31, 1968, and the names and addresses of their manufacturers. The purpose of this publication is to inform the public about approved equipment for safe use in mines and mineral and allied industries.

Jan 1, 1969

In this issue, the Bureau of Mines announces the availability of the latest of its Mineral Perspectives series: ?MP-4, mineral Industry of Western Europe." This publication describes the mineral industries of 19 Western European countries. For readers unfamiliar with this new series, reproduced below and on the two succeeding pages, is the section dealing with the mineral industries of France. Information regarding acquisition of this publication is found inside the back cover of this issue. FRANCE France is a moderately important producer of minerals, including iron ore, coal, potash, fluorspar, and uranium. In addition, France is a significant processor of imported minerals, chiefly for its own consumption. In general, it has exportable surpluses only of a little iron ore (low-grade ore exported to Luxembourg) and some nonmetallics.

Jan 1, 1977

Law of the Sea. - The Ninth Session of the Law of the Sea Conference resumed July 28 at Geneva and will run for 5 weeks. The 160-nation Conference began in 1973. Two of the major factors to be discussed are the transfer of technology to the UN-controlled Enterprise or mining authority, and how the 36-member Council will make decisions. As the session completed its third week, delegates expressed little hope of completing a treaty text this year. There was a feeling, though, that substantive issues might be settled so that a treaty text can be completed next year. The Deep Seabed Hard Mineral Resources Act signed by the President on June 28, provides an interim regulatory procedure for ocean mining activities conducted by U.S. nationals that may be superseded by a law of the sea treaty.

Jan 1, 1980

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976

This is the initial issue of STATE MINERAL SUMMARIES. This publication provides estimated data and summaries of mineral activities at the State level for 1988. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1989

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969