Search Documents

By W. H. Oppelt

The Federal Bureau of Mines investigated combustion of lignite in domes-tic heating equipment to obtain information on equipment performance and to evaluate testing procedures. Three types of domestic heating equipment were tested, ranging from a hand-tilled, magazine-type space heater to a ram-type overfeed stoker. Lignite was readily burned in each of the three units under various test conditions. Burnoff rates determined by adding weighed charges to the magazine were found to be in error because of shrinkage of the lignite when only a portion of the magazine capacity was consumed during a test. More reliable burnoff rates could be determined by carbon-nitrogen balances. A hand-fired magazine-type space heater (Booker heater) was operated without the furnace attachment at efficiencies to 75 pct. One test series was run with minimum supervision under conditions encountered in actual household operation. No mechanical trouble was encountered.

Jan 1, 1960

By John Gross

From the time when man first pounded one rock upon another or used heat and sudden chilling with water to disintegrate rock, the art of crushing advanced but slowly to the mule-driven arrastre and the Chilean mill stage until the advent of power-driven appliances made material progress possible. The combined efforts of manufacturers and operators have made modern machines highly efficient mechanically. Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or the Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere.

Jan 1, 1938

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By W. H. Coghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989

By G. B. Shea

In 192b, there wore 47 fatal accidents in the California petroleum industry, 14.6 per cent more than occurred in 1927 when 41 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. This increase in the number of fatal accidents for 1928 has caused the first upward trend in the fatality curve of the California petroleum industry since 1923. In no other year during the 6-year period have the fatalities in any one year been greater than those for the preceding year. This fact should be given serious consideration and study by the petroleum industry, and an endeavor should be made to cause the number of fatalities again to decrease and conform to the previous gradual declining trend of the fatality curve. The following chart shows the trend of fatal accidents during the past six years:

Jan 1, 1929

By Allen D. Look

Underground fires often prove difficult to control , and a small fire can quickly grow into a large one , endangering life and causing large property damage . Even a small underground fire may produce enough noxious gases to cause suffocation ; therefore , every precaution should be taken to prevent and control such fires . It is ironic that mine fires should be caused when utilizing materials that are in themselves fire - resistant ; yet , cutting and welding of iron and steel are proving to be common causes of underground fires in metal mines . This paper includes 19 examples of underground fires of this nature , and undoubtedly this is only a fraction of the number of similar fires that have occurred in the last few years . This paper will review some metal - mine fires caused by cutting or welding and point out precautions to be taken to prevent other fires from this cause .

Apr 1, 1948

Vanadium, molybdenum, and a titanium-10 percent vanadium alloy were evaluated for their susceptibility to stress corrosion cracking in a number of corrodents. Tests were conducted utilizing conventional U-bend techniques with subsequent evaluation in a pneumatic constant-load apparatus. Vanadium and molybdenum were generally resistant to stress corrosion cracking in the media studied. U-bend specimens of vanadium showed evidence of stress corrosion cracking in 6 li hydrochloric and 18 li sulfuric acids; however, tensile stress specimens exposed to these solutions did not exhibit stress cracking. Similar results were obtained when U-bend specimens of molybdenum were immersed in 10 percent formic acid. Titanium-10 percent vanadium alloy was susceptible to stress corrosion cracking in 10-percent (2.85 li) hydrochloric acid solution. Heat treating the alloy greatly reduced its corrosion rate and its susceptibility to stress cor-rosion cracking in this medium.

Jan 1, 1965

By G. R. Palmer

The Bureau of mines evaluated the elution of uranyl carbonate from a strong base resin with a mixed carbonate eluant in a fluidized system. The system consisted of a multiple-compartment ion-exchange (MCIX) elution column with a continuous flow of solution, except for short periods when the resin increments were withdrawn. The exchange of uranyl carbonate from the mill-loaded strong base resin with an eluant composed of 1.0 [M] NaaCOs plus 1.0 [M] NH4HCO3 was studied. The effects of solution flow rate, aqueous-to-resin flow ratio, column diameter, compartment height, initial resin concentration, and column length were examined. The experimental data indicate that for the eluant examined, a resin residence time of 240 minutes is necessary to attain 90-percent elution efficiency. Also provided is a technique for sizing an elution MCIX column form pilot plant experimental data.

Jan 1, 1979

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M') and the ratio of the maximum air velocity to the minimum air velocity (V') as measured in the cyclone entrance channel.

Jan 1, 1972

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following questions are frequently asked by coal users: (a) Will the coal lose any, of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when coal is stored? DISCUSSION (a) Loss of Heating Value Studies by the Bureau of Mines show that the loss of heating value of coal in storage commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh gas, and Sheridan (Wyo.) coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating Value of Coal During Storage, by H. C. Porter and F. K. Ovitz (p. 8):

Jan 1, 1943

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By Albert E. Long

THIS GLOSSARY is published lay the Bureau of Mines as a contribution too the mining literature to fill a long-felt need for a compilation of the terms used by the diamond-drilling industry. The first step toward preparation of the glossary was taken in October 1955 when the Diamond Core Drill Manufacturers Association (DCDMA) proposed that the Bureau of Mines undertake the cons compilation and publication of a glossary of the terms used by the diamond-drilling industry. The work was authorized in July 1956, and a preliminary draft of the glossary was completed in may 1958. Copies of the draft were submitted for review to members of the DCDMA and appropriate personnel of the Bureau of Mines. The final draft, incorporating the many helpful suggestions of the reviewers representing both the diamond-drilling industry and the Bureau of Mines, was completed in March 1959.

Jan 1, 1960

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

This manual covers the operation and lubrication procedures for the Eimco Pumpable Roof Bolting Machine. This machine meets U. S. Bureau of Mines Schedule 2G Approval. This manual is divided into three major parts: 1. Machine dimensions; 2. operating instructions and; 3. Lubrication. Whenever front or rear, right or left arc mentioned it is assumed that the reader is standing behind the machine looking toward the boom. The boom is at the front of the machine. Safety When leaving machine parked on an incline turn wheels into the rib or block wheels. Do not run over power cables. Make sure your power cable is up out of the way so others can't run over it. Machine has a fire suppressor system for the power unit. The remote actuator (pressure cylinder) is located at the operator's station. Components and service procedures on page 59.

Jan 1, 1976

By H. W. St. Clair

Sampling of heterogeneous mixtures of fused metals or solidified melts is subject to errors not met in sampling finely ground ores or granular materials. These errors arise largely because of the segregation of constituent metals that usually takes place during solidification. It is seldom that a random sample of a lot of metal will represent the composition of the entire lot. The problem becomes especially difficult when it is necessary to make accurate analyses for a segregated impurity present in very small amounts. This paper discusses some of the pertinent experimental observations made in selecting a method for sampling melts of aluminum and zinc containing small amounts of iron and silicon as impurities. Although this experimental study dealt only with sampling this specific combination of metals, many aspects of the study apply generally to any mixture of mol ten metals containing minor constituents that segregate rapidly during freezing of the melt.

Jan 1, 1949

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following; questions are arising n the minds of coal users: (a) Will the coal lose any of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when storing coal? In regard to the loss of heating value of coal in storage, tests made by the Bureau of Mines show that the loss commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh Gas, and Sheridan Wyoming coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating; Value of Coal During Storage, by H. C. Porter and F. K. Ovitz:

Jan 1, 1942

By Robert P. Vinson

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By S. M. Dar

The U.S. Bureau of Mines constructed a full-scale model of a 15-ft-wide coal mine entry to use in combination with finite-element analyses to investigate roof support systems and various types of roof bolts. The objective was to enhance understanding of the fundamental mechanics of the interaction between rock and supports and the relative integrity of bolted mine roof as a function of roof bolt type, length, spacing, and tension, and the basic characteristics of the roof strata. The laboratory test results, when correlated with computer simulations using fmite-element analysis and underground verification tests, should provide a basis for desigillng safer, more cost-effective roof control systems and help to establish guidelines for employing fully grouted resin and mechanically anchored bolting systems. The background for this research, the research approach, the methods and equipment employed, and the results are described in this report.

Jan 1, 1989