Search Documents

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in REscent years. The tenative ball-mill grindability method D409-35T4/was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-Mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity. ACKNOWLEDGMENTS This study was conducted at the Southern Experiment Station of the Bureau of Mines in cooperation with the University of Alabama. The Alabama liming Institute was of great assistance in furthering the investigation, and the work was undertaken largely as a result of its request that the Bureau of Mines should make certain studies of Alabama coals. Grateful acknowledgments

Jan 1, 1938

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By D. W. Frommer, M. M. Fine

"INTRODUCTION Laboratory mineral-dressing investigations covered by this report show that ores from Montgomery County, Ark., and Morgan County, Mo., are potential sources of barite and zinc. Fine grinding and froth flotation yielded drilling-grade barite from the former and chemical-grade barite and zinc concentrates from the latter.Samples from these deposits were subjected to a laboratory investigation to develop an economic and feasible treatment. The Arkansas ore, submitted by the Husky Refining Co., consisted of an intimate mixture of the economic mineral and quartz. Fine grinding and fatty acid flotation were utilized to effect a good recovery of a drilling-grade product. The other was a zinc-barite ore submitted by the Rocky Ford Mining Co., Stover, Mo. There was no problem in the recovery of zinc (most of which occurred as sphalerite), but the recovery of barite by flotation was complicated by the presence of gangue carbonates. Ultimately, an excellent recovery of barite was achieved with a relatively new type of flotation promoter, petroleum sulfonate.In recent years, barite has become one of the major industrial minerals as an essential ingredient in heavy drilling fluids, pigments, and chemicals. New sources of this important commodity are always interesting; thus, it is the purpose of this report to present information that may permit commercial exploitation of two deposits not in production."

May 1, 1952

By D. P. Desmond

The U.S. Bureau of Mines investigated leaching automobile catalysts with sodium cyanide (NaCN) solutions at high temperatures to recover platinum-group metals (PGM). The feed was virgin monolith rejects, used monolith, and used pellet catalysts. Leaching with a 5-pct NaCN solution for 1 h at 160° C dissolved over 97 pct of the PGM in the virgin monolith, over 85 pct of the PGM in the used monolith, and over 90 pct of the PGM in the used pellet catalyst. Over 99.8 pct of the dissolved PGM was recovered as a precipitate by heating the solution to 250° C for 1 h in an autoclave. The cyanide complexes were decomposed, and free cyanide was destroyed.

Jan 1, 2010

By Jos. R. Guiteras

This paper is one of a series describing; mining and milling methods and costs being published by the Bureau of Mines. It deals with the mineral resources of western South Dakota and describes the mining and milling of tantalite and associated amblygonite by the Black Hills Tin Co. and the Fansteel Mining Corporation. ACKNOWLEDMENTS Acknowledgment is made to Earl C. Schultz and Arthur I. Johnson, respectively superintendent and engineer for both the Black Hills Tin Co. and the Fansteel Mining Corporation, who contributed the information on mining and milling operations.

Jan 1, 1939

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

By G. Richards Gwinn

The mineral olivine, though known to mineralogists for many years, was of little commercial value in the United States before 1933. It was first described in 1790 by Johann Gottlieb Werner, who named it "olivine in allusion to its olive-green color. Commercial olivine first attracted attention because of its refractory properties. Further research has developed methods of extracting the magnesia content for the production of various magnesium compounds. Experimental and pilot-plant work also are in progress to make olivine available as a low-cost raw material for the production of magnesium metal.

Jan 1, 1943

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By Lawrence G. Houk

Lithium is the lightest of all metals, but as it deteriorates rapidly in air it has no structural applications. Alloys of lithium that will float upon water can be made with other light metals, but these ultralight alloys are not useful in aircraft production or elsewhere at present. Alone or alloyed with alkaline earth meals, lithium acts as reining agent on molten metals, and as a minor constituent with other metals it imparts characteristic properties to the allay. Lithium compounds have somewhat wider application in commerce than either the metal or the alloys. They are used in the glass, ceramic, chemical, and air-conditioning industries and less extensively in the optical, pharmaceutical, electrical, and textile industries. The United States is the leading producer anti consumer of lithium ores and compounds and apparently has the largest known ore reserves. The value of lithium ores and primary chemical byproducts produced is relatively small, yet the lithium chemical industry yields products worth hundreds of thousands of dollars each year, owing partly to the high degree of purity demanded by the trade for most finished products and to the low combining weight of lithium. Fortunately, the low-grade ores can now be concentrated economically, and this fact, together with our extensive reserves, assures adequate supplies to meet any reasonable increase in demand. Lithium is listed as essential by both the American and British war agencies, and its military importance may be greatly enhanced.

Jan 1, 1942

By W. V. Kuster

The investigation described in this report is part of a survey by the Federal Bureau of Mines of the titanium resources of the United States. The purpose of this project was to study a typical coastal deposit of beach sands in the Middle Atlantic States, particularly in the area surrounding the Delmarva Peninsula. The field investigation consisted of a reconnaissance survey of the Eastern Shore of Maryland, followed by surface sampling and drilling of the sands on Assateague Island, off the Atlantic coast of Maryland. The study covered the period January-December 1957. Detailed analyses were made of 5-foot sections of eight drill holes along the Maryland section of the island. The heavy-mineral fraction of these samples was separated by sink-float tests, using acetylene bromide as the heavy liquid. The minerals comprising the heavy fraction were examined microscopically, and mineral counts were made on selected samples.

Jan 1, 1959

By O. M. Bishop

"INTRODUCTION Early in World War II, the Bureau of Mines realized that reserves of fluorspar ore at many mines in the southern Illinois fluorspar district were not being developed as rapidly as the old ones were being depleted. At some mines the measured and indicated ore reserves were almost entirely depleted, although geologic factors favored new discoveries. The Leo mine, which had not been worked since 1938, was among this group of mining. The Bureau of Mines, together with the Illinois Geological Survey examined the property, studied the mine records and,geologic factors in 1944, and agreed that exploratory drilling was warranted Funds were,obtained for the work in the fiscal year 1945, and drilling was done; between October 27, 1944, and June 15, 1945.The property was owned in fee simple by the Hllside Fluor Spar Mines at the time exploration was begun in October 1944. Subsequently, in 1945, the Inland Steel Co. acquired of the Hillside property."

Jan 1, 1947

By Robert W. Ageton

Optimal planning for mining the deep, lead-zinc-silver deposits of the Coeur d'Alene mining district, Shoshone County, Idaho, could be facilitated by a knowledge of the magnitude and direction of the pressure acting in the virgin rock. The distribution of primary stresses should be considered in order to prevent possibly destructive mining-induced stress concentrations. This particular investigation was concerned with determining stress in a zone 4,000 feet below the surface and known to be ender stress concentrations due to mining operations. Disking of the stress-relief cores obtained in a vertical down hole permitted qualitative evaluation from visual observations; the results indicate that a high lateral stress existed at the time the measurements were made. Stress-ellipsoid determinations gave a compressive principal stress of -13,000 psi oriented about N 45° W and nearly horizontal, a compressive principal stress of -11,000 psi oriented about S 45° W and abut 60° off the vertical pointing away from the vein, and a compressive principal stress -5 -7,000 psi oriented N 45° E and about 60° off the vertical, pointing toward the vein. Subsequent to the overcoring stress-relief drilling, a rock burst occurred about 100 feet northwest of the test site.

Jan 1, 1967

By C. C. Knox

In Kiowa County, Okla., extensive deposits of clay are closely associated with pre-Cambrian anorthosites and gabbros. Investigation by the Bureau of Mines, including 1,723 feet of auger drilling, has shown the presence of very large quantities of clay containing between 20 and 25 percent alumina. All of the material contains large amounts of impurities, and even the best clays, selected for their relatively low content of iron, titanium, and magnesium, are unsuitable for the production of alumina by the sulfuric-acid process The soda-lime process gave somewhat better results, the product being nearer specification for commercial alumina. The clays are not amenable to beneficiation by simple sedimentation processes, and the alumina content could not easily be increased to produce material suitable for any alumina process.

Jan 1, 1948

By R. S. Sanford

The Claim Point chromite deposits are at tidewater near the southern tip of the Kenai Peninsula in southwestern Alaska, The United States Geological Survey had a field party in the region from July until September 1940 under P. W. Guild, assistant geologist; maps and geological data were assembled and made available to the Bureau of Mines. A preliminary investigation of the deposits at Claim Point by the senior author during July 1941 was followed by surface sampling and core drilling to determine the quantity and grade of the ere, The Geological Survey was represented at the project by George O. Gates, geologist. Cores were checked and the structural data revealed by drill cores were interpreted. The principal chromite deposits have been sampled and delimitated by trenching and core drilling. Other deposits were trenched and sampled but were too small or too low-grade to warrant core drilling.

Jan 1, 1949

By William A. Beck

The K.T. Dome Mine in Owen and Henry Counties, Ky., has been operated intermittently under several different owners since the early nineteen hundreds. No record of total production is available, but it is said that during 1943 and 1944, while being operated by the Twin Valley Mining Co., 30 cars of zinc concentrates and 10 cars of lead concentrates were shipped. The vein can be traced for about 10 miles along the strike from Lockport, Henry County, to Big Twin Creek in Owen County. It pinches and swells both vertically and horizontally and is reported to average 20 inches in width. In order to develop additional reserves on the property, the Bureau of Mines drilled four holes on the south extension of the vein. Drilling disclosed that the vein dips to the west on the south side of the Kentucky River and is continuous along the strike and in depth. However, the extent of mineralization in the vein varies widely.

Jan 1, 1949

By R. H. Jefferson

An electrochemical method to selectively determine sulfur dioxide in the presence of sulfur trioxide was investigated. A hydrophobic gas-permeable membrane separates the gas sample solution from an internal filling solution containing a fixed quantity of chloride ion and a sufficiently large excess of sodium bisulfite so that its concentration may be considered constant. Sulfur dioxide diffuses through the membrane to dissolve in the internal filling solution and liberates an equivalent quantity of hydrogen ions. The electromotive force between a precision-ground, flat-ended pH electrode, which acts as the sensing element, and a chloride sensing electrode, which acts as the reference element, gives a direct measure of S02 in the gas sample solution. Calibration curves in water, tetrachloromercurate (TCM) , and citrate buffer absorption solutions were closely parallel with slopes in their linear segments, ranging from 57 to 52 mv/decade of S02 concentration. The slopes compare reasonably well with the theoretically expected slope of 58 millivolts at 21° C. The water standard curve was linear with respect to the logarithm of S02 concentration from 1 to 1,000 ppm S02; the TCM standard curve was linear from 10 to 2,000 ppm S02; and the citrate standard curve was linear from 30 to 5,000 ppm S02' The high efficiency and nontoxicity of citrate favor it as a substitute for the conventionally used TCM in the absorption solution.

Jan 1, 1976

By George W. Heim

Before and during World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for development included those expected to contain metals of importance in the successful prosecution of the war. This report describes the work performed and results obtained in developing the Daggett Chief manganese deposit near Manila, Daggett County, Utah (fig. 1), during 1941. The work comprised mapping and a study of the geology by the Federal Geological Survey, and bulldozer and hand trenching, sinking of two shafts, and sampling by the Bureau of Mines. Work was started April 17, 1941, and was completed June 28, 1941. Two bulk samples for metallurgical testing were taken.

Jan 1, 1950

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By Ellis S. Hertzog

The relatively large amount of phosphorous occurring in many iron ores limits their usefulness aid sometimes renders them valueless under present conditions of nip-iron manufacture. A practical method for removing the phosphorus would be valuable to the iron and steel industry. Gravity concentration has been of little value as far as the removal of phosphorous is concerned, because the compounds of this element are, as a rule, disseminated very finely. Removal of the phosphorous by leaching is not a new idea and has been the subject of some investigation,3,4/ out for data :lave been published. W.R. Crane published analyse of various ore bodies in the Birmingham ham district. The hard or unleached ores a .re much higher in phosphorous than the Soft, leached ores along the outcrops. This fact indicates that as mild a leaching agent as water removes phosphorus effectively if enough time is allowed for it to react. As the forms in which phosphorous occurs in the iron ores are important in the consideration of any leaching operation, much time was expended in devising a method for determining them. According to Professor McVey, University of Alabama, the phosphorous-bearing minerals in the red iron ores of Alabama have not been positively identified by any microscopic methods.

Jan 1, 1935