Search Documents

By Kenneth Lipman

Auxiliary equipment was assembled around a purchased oscillograph to permit observation of the current and voltage characteristics of low-energy, capacitance-discharge sparks having durations of at least 10 mµ-sec. Circuit details of the assembled apparatus, performance characteristics of the complete system, and some preliminary data from representative self-initiated sparks are given in this report. INTRODUCTION One of the subjects of continuing research by the Federal Bureau of Mines Division of Explosives Technology is the ignition of explosive-gas mixtures by means of low-energy capacitance sparks. Quite early in these investigations it was recognized that understanding the gas-ignition phenomena would be facilitated by detailed information about the performance of the ignition source (spark) under the actual conditions of interest; however, the sparks of practical interest are nonrepetitive transient phenomena whose duration could reasonably be estimated to be in the time range of 1 mµsec. to 1 µsec. As such, the only feasible method of obtaining detailed information was and is oscillographic representation of the pertinent current and voltage transients. It was not until 1947 that a suitable, commercial, dual-channel oscillograph could be obtained as the basic instrument for these studies; the instrument specified in 1947 was delivered in 1950. This paper describes the auxiliary

Jan 1, 1959

By M. E. Tyrrell

Mixtures of zirconium diboride and iron, cobalt, and nickel were resistance sintered to high-density compacts using modified electric welding equipment. To evaluate the use of iron, cobalt, or nickel as binders for zirconium diboride, the sintered compacts were examined in polished section and tested for crushing strength, hardness, microhardness, oxidation rate, and resistance to mechanical shock. Each of the zirconium diboride-metal mixtures produced brittle cermets, but the hardness was generally satisfactory. The iron- and cobalt-bonded cermets exhibited rather poor oxidation resistance. Cobalt provided the least brittle bond, and nickel, the hardest and most resistant to oxidation. Iron tended to form chalky compacts with low resistance to mechanical shock.

Jan 1, 1963

By W. S. Sanner

This report describes the commercial application of the launder screen in anthracite-industry fine-coal cleaning operations. No new device, the launder screen has been used since the early part of the present century to size, screen, classify, and deslime the fine-anthracite sizes (Buckwheat Nos. 1 through 5) recovered by "river-coal" men dredging along streams draining the anthracite fields. The launder screen is stationary, has no moving parts, requires ample water for operation, and can be constructed economically on the job. Essentially, it consists of a wooden trough with baffles placed through its width to form a well system. The wells are covered by fine-mesh woven-wire screening. Each well is tapped with a number of orifices, and the hydraulic suction head developed in this manner removes high-gravity fines and slimes through the screening as underflow to waste. Material retained on the screen surface discharges as overflow product.

Jan 1, 1954

By Charles Janin

The recovery of gold from sands and gravels is one of the oldest forms of mining; it antedates history and has been practiced by savage peoples. In North America the search for placer gold has been a powerful agency in the exploration and development of unknown regions and has profoundly influenced the course of our civilization. With the progress of invention, the improvements in machinery, and the availability of large capital for the conduct of great operations, the tendency in placer, as in many other branches of mining, has been toward the working of extensive but comparatively low-grade deposits. The early miner washed the rich spots in stream beds or terraces with his pan, his long tom, and his primitive sluice. Then followed the growth of hydraulic mining and the use of giants supplied with water under pressures of hundreds of pounds to the square inch that could work at a profit gravels whose gold tenor was less than 3 cents to the cubic yard. Finally came the dredge that could handle deposits lying so far below water level as to be beyond attack by other methods. Although the gold dredge was first successful on a commercial scale in New Zealand, it has reached its present strength and efficiency in this country and its development is a monument to the daring, per- severance and technical skill of the many men, mine owners and engineers who have each contributed something to the final result. The Bureau of Mines, authorized to conduct investigations for the purpose of increasing efficiency in the mineral industries, had its attention called some years ago to the need of a comprehensive report on gold dredging in the United States. The director of the bureau recognized that such a report should summarize the development of the gold dredge, should describe in detail the essential features of present-day dredges, should discuss the facts that determine whether a placer deposit can be profitably dredged, and should point out the approved methods of prospecting placer ground and of operating dredges. At the request of the director, the author undertook the preparation of such a report and has been intermittently engaged on the task for several years. This bulletin is the outcome of his labors. He hopes that it will prove of interest to designers and builders of dredges, to mining engineers, and to persons who may contemplate investing capital in placer-mining ventures.

Jan 1, 1918

By John C. Ferm

This report summarizes the results of an investigation of geologic factors that contribute to roof quality in underground mines in the Pocahontas #3 coal bed in southern West Virginia and southwestern Virginia. The investigation consisted of three phases, the first of which was selecting for detailed study five mines which represented the range of roof conditions, mining practices and geologic phenomena. This was accomplished by a statistical analysis of questionnaire data from 35 mines. The second phase consisted of detailed mapping in a "good" and a "bad" top area in each of the five selected mines and resulted in a qualitative assessment of geologic factors contributing to roof £alls. In the third phase, five mines were selected in which most non-geologic factors believed to contribute to roof falls were relatively constant but displayed a wide variety of geologic characteristics. Data from these mines were analyzed to test the qualitative assessments from Phase II. The primary result of this investigation is that slickensides arising from different geologic causes are the major geologic features leading to roof falls. These slicken-sides are found in ancient slump deposits, fire clays and sandy fire clays and channel contacts. Falls also occur where thick sandstone bodies directly over-lying the coal contain abundant shale or ironstone pebbles and coaly strips. The best top material is a sequence which consists of shale grading upward to sandy shale and sandstone within 30 feet of the top of the coal. Thick sand-stone units (301) without pebbles also provide good top.

Jan 1, 1978

By Louis R. Iverson

Patterns of species colonization, biochemical interaction among species, and competitive phenomena were studied in four reclaimed areas in western North Dakota ranging in age from one to four years after mining, along with a site from a native mixed grass prairie for comparison. Early successional changes in floristic composition and soil chemistry were quantified. The mined sites had been contoured, topsoiled, fertilized and seeded. Despite seeding of agronomic species, initial colonization was by fugitive species; analysis of the seed bank in topsoil showed that the most dominant colonizers immigrate after topsoiling. Of the 95 species encountered, Kuchia scoparia was the most dominant in the first two years following mining. Kochlo had relatively low densities in the first year (50-80 plants m-2), but was robust and attained heights of 88 cm with a biomass of about 400 g m-2 In the second year, the plant densities increased to over 10,000 plants m"2 but the height and biomass were reduced to 15 cm and 90 g m-2. However, during the third and fourth years Kochia density declined and was practically non-existent by the fourth year, while the planted Agropyron grasses had concomitantly increased. Other pioneers like Amaran thus retroflexus, Chenopodlum album, Helianthus annuus, Salsola spp. And Setaria spp. showed a less abrupt but similar decline. Chemical analysis of the soils over the same time period showed decreases in electrical conductivity (E.C.), and in the concentrations of P, Ca, Mg, Na, Li, Sr, and SO4 (due to leaching), while N increased. Field studies were conducted on the competitive relations between the dominant species - Kochia scoparia and Agropyron spp. - during early succession. It was found the Kochia acted as a "nurse" crop for several months during the first year of Agropyron spp. establishment, but then began to shade heavily by late July, thus reducing grass tillering. Field and growth chamber experiments on the intraspecific competition relations of Kochia demonstrated that its density and dry matter production, per plant and per unit area, conformed to several laws of plant population biology. Autotoxicity or the depression in growth of a species by its own degradation compounds, in Kochia, appears to be the main factor causing the decline in its growth. Results from a field experiment indicated that thinning dense second year Kochia stands to the density of first year stands did not alter the growth of Kochia, providing strong evidence for autotoxicity. Similarly, several growth chamber experiments demonstrated that small amounts of decaying Kochia leaves and especially roots were toxic to Kochia growth, but not Melilotus officinalis or Agropyron canlnum, Chemical analysis of the soils and plant tissues indicated nutritional im¬balances as shown by P/Mn and P/Zn ratios may be responsible for autotoxicity. In addition to Kochia, a bioassay experiment showed allelochemics to be important in several other colonizing species. Although our results indicate that later stage species generally have greater toxicities than first year colonizers, autotoxicity in the very initial stages seems to be accentuated by harsh habitat conditions. Several practices (mowing. fire, etc.) are used to manage grasslands. Mowing of the first year erect, annual, colonizing vegetation was shown to be beneficial in the growth and establishment of wheatgrasses after mining in western North Dakota. Plots containing Kochio predominantly were mowed in mid-and late-July, and in mid-August, during the first year of growth after recontouring, replacing topsoil. seeding and fertilizing. It was found the Kochia densities were reduced to two percent of the control and its biomass reduced to less than one-third when the area was mowed in mid-August. On the other hand, wheatgrasses showed increases of 23% in stem density and 860% in biomass production over the controls when mowed in mid-August. The mowing of Kochia just before seed-set apparently reduces interspecific competition between Kochia and Agropyron spp. during the following growing season. The method is highly recommended for use in hastening the establishment of planted grasses.

Jan 1, 1982

By D. Bienstock, J. H. Field, M. J. Lempel

A computer program is presented to perform the detailed and numerous calculations required for determining the interface temperatures and steady - state heat flow through a furnace wall composed of several refractories in layers . A method is developed that will allow the designer to determine the various thicknesses for each refractory layer to minimize either the total wall thickness or the cost of the wall per unit of area . A sample problem is presented and analyzed to illustrate the techniques involved .

Jan 1, 1964

By G. F. Kuncir

The analysis described herein evaluates the Bureau of Mines Program for Advancing Mining Technology - Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to ail aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, Transportation, and Treasury, the Central Intelligence Agency, the Environ- mental Protection Agency, the Federal Reserve System, the interstate Commerce Commission, and the Securities and Exchange Commission, whose primary mission is the collection of data in nonmineral subject areas, but in which the mineral industry is a component.

Jan 1, 1983

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By Guy E. Dent, Hugo E. Kuehn

"SUMMARYFor making a comparison of magnetic surveys measured from the ground and from the air, Worcester County, Maryland, was chosen as a proving ground. Vertical magnetic intensities were observed on the ground, and total magnetic intensities were observed from the air. A comparison of the two magnetic maps reveals similar large magnetic features, but these are displaced in some instances by distances greater than a mile. Magnetic terrane in the two charts is of the same type but often differs greatly in respective characteristic features.The sacrifices in accuracy that may be expected from the use of different systems of diurnal magnetic corrections on ground observations constitute a part of this report.INTRODUCTIONThe value of magnetic surveys for gaining information concerning the crystalline basement is recognized increasingly. That this topography is often reflected to a major degree in the overlying sediments with certain offsetting is well understood. Even where such sediments are deep, the surface topography of upper formations often reflects this bedrock topography to a certain degree."

May 1, 1947

By Sidney Speil

In the study of clays and related minerals, the analytical techniques commonly employed in mineral analysis are not always applicable. The X-ray examination of a clay sample usually will show the major constituents, but often minor· clay impurities will not be detected because of line broadening and the similarity of the main lines of clay· mineral diffraction patterns, The petrographic analysis of clay minerals with clay particles as small as a few microns is usually difficult. With still smaller particles, a gross effect often is noted in which a mixture of several constituents gives the appearance of a single constituent with the mean optical-characteristics of the mixture. 3/ The electron microscope has recently been used to study clay particle shapes of various aluminosilicates. 4/ However, this method has not yet been sufficiently explored. The Chemical method in which a mineralogical analysis is calculated from the oxide chemical analysis has been discussed by Wilson 5/ and others, and many of the shortcomings have been pointed out. It should also be recognized that the variable alkali and alkaline earth content of bentonites makes it inaccurate to assign these basic elements arbitrarily to feldspar or mica in any clay that contains appreciable bentonite.

Jul 1, 1944

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By Manuel Gomez

The heat contents of thermally dried lignite, subbituminous B coal, and their corresponding low-temperature chars were determined at various temperatures below the highest temperature to which these materials had been exposed before testing. Similar studies were made on high-temperature char and coke, spent shale, and ash prepared from both coal and spent shale. Heat content of the carbonaceous materials tested correlated well with temperature. Heat con-tent results for spent shale compared well with the published results. Statistical analysis of experimental data together with published information showed moisture, volatile matter, carbon content, and temperature to be the principal variables influencing the specific heat of coal. The specific heat of devolatilized carbonaceous substances, char and coke, approached that of graphite as the carbonization temperature was increased. The elemental specific heats of coal constituents, estimated from the ultimate analysis and the specific heat of coal, compared favorably with published elemental specific heats.

Jan 1, 1965

By R. R. Sayers

That the maintenance of proper air conditions is a most important factor in the control of occupational hazards is shown by the large amount of material presented each year through the technical journal's on the effects on workers of injurious dusts, gases, and variations in temperature and humidity.. SUMMARY OF RECENT LITERATURE ON EFFECTS ON WORKERS OF EXPOSURE TO DUSTS The subject of the control of dust and dust diseases continues to be a matter of serious concern in most of the industrial countries of the world, as indicated by the following summary of reports published in a number of foreign countries as well as in the United States. Australia. The Workmen's Compensation Act of 1920 for New South Wales3 provided for the promulgation of schemes for the compensation of workers dis- abled by silica or other dust. In 1924 the prevalence of silicosis and tuberculosis among Sydney stonemasons, quarrymen, sewer miners and rockchoppers was investigated by a Technical Committee of Inquiry, appointed upon the recommendation of the New South Wales Board of Trade. The findings of this committee were published by the Government in 1925. No scheme was promulgated by the Government and in 1926 the Act was amended limiting its scope to workmen disabled by disease caused by silica-dust. This was promulgated and gazetted on September 16, 1927, and applies to men working in sandstone as stonemasons, quarrymen, rockchoppers, and sewer miners in the County of Cumberland.

Feb 1, 1931

By August J. Kwitowski

This report presents the results of a joint Bureau of Mines-U.S. Department of Energy project that evaluated a newly developed low-coal mining system: the 4M miniminer system. The evaluation took place from April through October 1981 and determined potential health, safety, and productivity factors for the mining system using the surface test facilities at Bruceton, PA. The planning, testing, results of testing, and a summary evaluation of the 4M miniminer system are included in the report. The miniminer system was found to be a very good concept with future potential for safe, healthful, and economic production in thin-seam mining. The mining system was also judged to have considerable potential for use in some coal seams that are presently considered unminable by other existing mining equipment. The preproduction, prototype version of the miniminer system that was tested suffered from several safety and production problems. These problems are also described, along with suggested remedies.

Jan 1, 1989

By D. A. Reynolds

THIS PAPER gives results of an investigation of the composition and carbonizing properties of coals from the Beckley bed, Caretta No. 5 mine, Susanna, McDowell County, and Glen Rogers No. 2 mine, Glen Rogers, Wyoming County, W. Va. The investigation included BM-AGA carbonization tests at. 800° and 900° C. and various chemical and physical tests designed to evaluate agglutinating, plastic, and expanding properties of coal. Both coals were of low-volatile bituminous rank, and each was blended with 70 and 80 percent high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa. The Beckley bed was 39 to 58 inches thick at three points in the Caretta No. 5 mine, and the coal was 39 to 49 inches thick. The carbonizing sample contained 83.0 percent fixed carbon on the dry, mineral-matter-free basis. It contained 3.1 percent moisture, 15.8 percent volatile matter, 72.4 percent fixed carbon, 0.7 percent sulfur, and 8.7 percent ash, as carbonized. The ash softened at 2,680° F. The free-swelling index was 7;i, and the agglutinating value was 7.7. This sample fused weakly in the Gieseler plastometer; its blends with 70 and 80 percent Pittsburgh coal attained maximum fluidities of 830 and 600 dial divisions per minute, respectively. The single coal yielded 83.0 percent coke at 900° C. Yields of other carbonization products per ton of coal at 900° C. were: Gas, 9,950 cubic feet; tar, 3.5 gallons; light oil, 1.36 gallons; and ammonium sulfate, 16.3 pounds. Blending with Pittsburgh coal lowered the yield of coke and raised the yields of other products significantly. Caretta coal yielded strong, blocky coke at 900° C., 89 percent of which was plus-2-inch size. Strength indexes of 900° C. coke from 30:70 blends of Caretta No. 5 and Pittsburgh and of Pocahontas No. 3 and Pittsburgh coals were, respectively: 2-inch shatter, 68 and 53; 1%-inch shatter, 90 and 85; 1-inch tumbler, 50 and 53; and %-inch tumbler, 62 and 65. The specific gravity of the 900° C. gas from Caretta No. 5 coal was 0.272, and the heating values were 491 B. t. u. per cubic foot and 2,440 B. t. u. per pound of coal. The blends yielded much richer gas. Yields of tar acids and bases (0.09 and 0.04 gallon per ton, respectively) were within the normal ranges for low-volatile coals. Caretta No. 5 coal expanded 7.5 percent in the sole-heated oven at a charge density of 55.5 pounds per cubic foot. The blends containing 70 and 80 percent Pittsburgh coal contracted 4.8 and 7.5 percent, respectively.

Jan 1, 1953

By John P. Capp

Information is summarized on the major uses of fly ash and prospects for utilization in agriculture and in brick and mineral-wool manufacture. Technological aspects of utilization are discussed and references are given to the work of many of the leaders in the fields of fly ash production, processing, and utilization.

Jan 1, 1970

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1977