Search Documents

By Forrest T. Moyer

The safety record of the metal mining and milling industries in 1965 is reviewed by the Bureau of Mines. The overall injury-frequency rate of 23.77 per million man-hours was 5 percent lower than in 1964 and was the lowest annual rate in a statistical history beginning with 1931. The injury-severity rate of 3,521 days lost per million man-hours in 1965 represented a 5-percent improvement over 1964. However, the total of 3,825 disabling work injuries comprised 61 fatal and 3,764 nonfatal injuries, one and 92 more, respectively, than in 1964. At primary nonferrous smelters, refineries, and reduction plants, the injury-frequency rate of 8.97 per million man-hours in 1965 was 13 percent lower, but the severity rate percent higher than in 1964. these plants in 1965, 4 more of 1,173 days lost per million man-hours was 17 There were 12 fatal and 971 nonfatal injuries at and 28 fewer, respectively, than in 1964.

Jan 1, 1969

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By J. M. Stuve

Thermodynamic properties were determined by the Bureau of Mines for the intermetallic compound, TiA13. Heat capacities were obtained from 5 to 303 K by adiabatic calorimetry. The derived value of S2 1s is 22.08±0.07 cal/deg¬mole. Enthalpies relative to 298 K were obtained from 298 to 1,413 K by copper-block drop calorimetry. No anomalous thermal behavior was noted in the temperature ranges investigated. Low- and high-temperature data were combined with a known enthalpy of formation at 298 K to give values of enthalpy of formation and Gibbs energy formation, 0 to 1,400 K.

Jan 1, 1974

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By William W. Adams

The quarrying and related industries of the United States made a large gain in employment (man-hours of work) in 1942 with a somewhat smaller number of men employed than in 1941. This was accomplished chiefly by increasing the number of workdays per man and also by increasing the length of the workday. In spite of the greater volume of work performed, the industry had a more favorable accident-frequency rate in 1942 than in the previous year. Accident and employment reports from operating companies showed that the industry employed 84,270 men for an average of 271 days per man in 1942, with a volume of work of almost 181 million man-hours. The average workshift comprised 7.93 hours, and the number of man-shifts worked totaled nearly 23 million. Injuries from accidents in and about the quarries and plants caused disability to 6,461 employees, 112 of whom died as a result of their injuries, including 28 employees whose lives were lost in a single disaster. The accident-frequency rate in the industry was 35.73 per million man-hours worked, comparing favorably with a rate of 40.11 for the previous year. However, the figure for 1942 included a death rate of 0.62 per million man-hours which, because of the disaster referred to, was considerably higher than the fatality rate of 0.44 for 1941. Had the disaster not occurred, the fatality rate for the industry for 1942 would have been 0.46. The major disaster in which 28 lives were lost occurred on March 26 at the Sandts Eddy quarry of the Lehigh Portland Cement Co. near Easton Pa.

Jan 1, 1944

By Thomas G. Murdock

The possible contribution of an improved mineral economy to the further advancement of the lesser developed regions of the world is a vital consideration today. Many of the newly independent countries recognize the problems and the challenge involved in orderly development of mineral resources. Some countries are inventorying resources, planning development, and encouraging local and foreign participation. The Malagasy Republic, composed of the island of Madagascar and the immediately adjacent islands, formerly the French Overseas Territory of Madagascar, is one of the members of the French Community which achieved independence in 1960. It is making real progress towards improving its mineral economy, an effort particularly remarkable considering the generally unfavorable geographic location of the area with respect to world markets and what is, after all, a comparatively sparse-economic mineralization in the light of discoveries to date. Most of the development of the Malagasy economy before independence was fostered by French private enterprise, although the State participated in some ventures. Since independence, the Government has encouraged private investment from a variety of sources through favorable legislation and has indicated that legitimate investment projects that will further advance social and economic programs will be welcome.

Jan 1, 1963

By Thomas G. Murdock

The possible contribution of an improved mineral economy to the further advancement of the lesser developed regions of the world is a vital consideration today. Many of the newly independent countries recognize the problems and the challenge involved in orderly development of mineral resources. Some countries are inventorying resources, planning development, and encouraging local and foreign participation. The Malagasy Republic, composed of the island of Madagascar and the immediately adjacent islands, formerly the French Overseas Territory of Madagascar, is one of the members of the French Community which achieved independence in 1960. It is making real progress towards improving its mineral economy, an effort particularly remarkable considering the generally unfavorable geographic location of the area with respect to world markets and what is, after all, a comparatively sparse economic mineralization in the light of discoveries to date. Most of the development of the Malagasy econorny before independence was fostered by French private enterprise, although the State participated in some ventures. Since independence, the Government has encouraged private investment from a variety of sources through favorable legislation and has indicated that legitimate investment projects that will further advance social and economic programs will be welcome.

Jan 1, 1963

By E. Morrice

The Bureau of Mines investigated methods for beneficiating platinumgroup metal ores from the Stillwater Complex , Montana , as part of its program to increase the supply of critical and strategic minerals and metals from domestic resources . This report presents results of a 5- day continuous campaign employing a pilot flotation mill to recover sulfide concentrate containing platinum- palladium values from anorthositic ore . A mercaptobenzothiazole - sulfuric acid reagent suite was used . The pilot flotation mill was operated at an average feed rate of 106 lb/ hr of ore . A rougher concentrate containing 8.5 pct of the feed was prepared ; it assayed 1.1 oz /ton Pt and 3.5 oz / ton Pd . Recovery of platinum and palladium were 91 and 87 pct , respectively .

Jan 1, 1965

By N. S. Dalal, X. Shi

"It has been recently suggested that the exceptionally high antitumor and antibacterial activity of natural fredericamycin A (FMA) is related to its ability to spontaneously generate the superoxide anion (02-) and hydroxyl (""OH) radicals in aerobic solutions [Hilton, B. D., Misra, R., & Zweier, J. L. (1986) Biochemistry 25, 5533]. With a view to understand the mechanistic details, attempts were made to reproduce earlier electron spin resonance (ESR) evidence for the oxygenated free radical formation in well-aerated solutions of natural FMA in dimethyl sulfoxide and dilute H 20 2• Little or no evidence was obtained for the formation of the 0 2- and methoxy (""OCH3) radicals, while the detected formation of the 'OH and methyl ('CH3) radicals was attributable largely to mechanisms not involving FMA. These results thus reopen the T question regarding the mechanism of its exceptionally high tumoricidal-bacteriocidal activity. This paper reports on an electron spin resonance (ESR) investigation of the formation of oxygenated free radicals in solutions of natural fredericamycin A (abbreviated as FMA) which has recently been reported to be a highly potent anti¬tumor antibiotic (Pandey et al., 1981; Warnick-Pickle et al., 1981). The impetus for this undertaking was provided by recent reports (Hilton et al., 1986; Stinson, 1986) suggesting that the strong tumoricidal activity with high therapeutic—toxic index of FMA was related to its ability for the spontaneous generation of superoxide anion (02-) and hydroxyl (OH) radicals. For example, the suggested mechanism for the formation of 02- by FMA was (Hilton et al., 1986)FMA-OH + O2 FMA-O + H+ + 02-Here FMA—OH is simply the FMA molecule emphasizing the —OH moiety which becomes FMA-O, the free radical rep¬resenting the oxidized form of the drug. While some other highly effective anticancer drugs in current clinical application, such as bleomycin, are also thought to exert their antitumor effects via the formation of reactive drug-based or oxygenated free radicals (Carmichael et al., 1985; Gianni et al., 1983), FMA was considered unique in that only in this case the free radical formation was thought to be spontaneous, rather than through a metal- or an enzyme-activated process (Hilton et al., 1986; Stinson, 1986). Thus it was suggested (Hilton et al., 1986; Stinson, 1986) that FMA could be the forerunner of a new class of anticancer drugs. However, we noted that while the hypothesis seemed plausible, the reported ESR spectral evidence appeared to be ambiguous. Because of the high significance of the earlier conclusions (Stinson, 1986), we undertook a systematic ESR study of the radical formation in FMA solutions, and as discussed below, our conclusions disagree with those reported earlier."

Jan 1, 1989

By B. W. Madsen

The Bureau of Mines conducted a large-scale (6.4 t), long-term (2,165 days) test to gain a better understanding of the leaching characteristics of chalcopyritic ores. An ore sample containing 0.77 pct Cu was leached in a fiberglass column by downward percolation of acidified ferric sulfate solutions. Three sets of leaching conditions were investigated: (1) ambient temperature leaching, (2) elevated temperature (50° to 60° C) leaching, and (3) elevated temperature leaching after inoculation with thermophilic bacteria. Leaching at ambient temperature resulted in a copper extraction rate of 0.44 pct per 100 days. Increasing the temperature to 50° to 60° C resulted in decreased activity of natural mesophilic bacteria, and the leaching rate decreased to 0.22 pct per 100 days. The pH was lowered from 2.0 to 1.6, and nutrient solutions that contained thermophilic bacteria were added. This procedure resulted in an increase in the ferric-to-ferrous iron ratio and an increase in the copper leaching rate. However, the increased leaching rate was not sustained, and 120 days after inoculation the bacterial activity declined, the ferrous iron content increased, and the copper leaching rate decreased.

Jan 1, 1983

By H. N. Dunning

A comprehensive production research program, now in progress at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville, Okla., includes studies of the displacement of petroleum from sand by detergent solutions. An earlier report (12)2/ presented the results of an extensive research program to determine the value of detergents as floodwater additives. This report presents later results of the detergent-testing program (13, 17). Although water-flooding methods and controls are constantly being improved to increase the production of oil from secondary-recovery operations, considerable crude oil commonly remains.in place after a water flood has been terminated. Therefore, the possibility of improving the efficiency of a waterflood by the use of detergents is of increasing interest. The effects of many substances on the efficiency of water flooding have been investigated in laboratory studies (5, 11, 13, 17, 19, 24). Of the various sub-stances tested, only surface-active agents were consistently effective in removing oil from sand. Results of laboratory studies presented in earlier reports (9, 11, 12, 13) show that many detergent solutions effectively displace petroleum from sand surfaces under varying conditions encountered in centrifuging, manual and mechanical agitation, ultrasonic vibration, and imbibition.

Jan 1, 1957

By R. E. Siemens

A process is being developed by the Bureau of Mines to selectively recover nickel and cobalt from low-grade domestic laterites. In laboratory evaluation of the process, the oxides in the laterite were selectively reduced with carbon monoxide at temperatures from 350° to 600° C. For material containing more than about 5 percent magnesia, pyrite additions or post-reduction heat treatments were necessary to achieve satisfactory nickel and cobalt extraction for this range of reduction temperatures. Multistage leaching of the reduced material at ambient temperature and pressure in the presence of oxygen, ammonium sulfate, and ammonium hydroxide extracted up to about 90 and 85 percent of the contained nickel and cobalt, respectively. The nickel was selectively recovered from the leach solution by solvent extraction and was then stripped from the loaded organic with dilute sulfuric acid to provide a nickel-rich electrolyte. Treatment of the raffinate with hydrogen sulfide resulted in the recovery of cobalt as a sulfide. The only contaminant in solution was magnesium which was removed by ion exchange or precipitation. In this process the energy requirements are relatively low and except for minor operation losses, only coke and oxygen are consumed.

Jan 1, 1975

By D. C. Dahlin

The Bureau of Mines investigated the Ketchem Dome tin prospect in east-central Alaska to evaluate the tin resource. The studies included field investigations, mineralogical characterization, and concentration of the tin-bearing minerals. The tin mineralization consists of cassiterite (Sn02), which occurs as grains disseminated in a greisen (quartz-mica) matrixo A bulk sample from the largest and best-developed greisen vein exposed at Ketchem Dome contained 0.51 pct Sn. Concentration of the cassiterite by gravity table methods resulted in a product that contained 56 pct of the tin at a grade of 41.4 pct Sn. The mineralization exposed at Ketchem Dome is typical of greisen found in the area and elsewhere in interior Alaska.

Jan 1, 1987

The U.S. Bureau of Mines (USBM) has developed a test procedure to compare the initiating strength of detonators by using adjustable-sensitivity liquid explosives. Various tests of detonator strength are currently used by the industry, but many of them do not quantify the ability of detonators to initiate detonation reactions in an explosive charge. The USBM used mixtures of nitromethane and ethylene diamine, the sensitivity being "fine-tuned" by 2-nitropropane. Military standard J-2, commercial No.6, and commercial No.8 detonators were evaluated using three test configurations: (1) axially immersed in the test explosive, (2) tip just touching surface of the explosive, and (3) immersed transversely in the explosive. Markedly different results were obtained for these three configurations, indicating that the directional effects are important. This explains why different detonator strength tests do not correlate well with each other. Some tests, such as the sand bomb and underwater, measure the total energy out-put, while other tests, such as the plate dent, test measure the energy in the axial direction. The USBM's test data indicate the importance of conducting the experimentation in the manner in which the detonator is actually intended to function.

Jan 1, 2010

Three -dimensional boundary value problems are difficult to solve. Indeed, while the separation of the scalar wave equation can be effected in 11 different coordinate systems, an analytic solution requires that the boundaries, both external and internal, possess the same symmetry as the coordinate system. Numerical methods are thus of great importance for the solution of such problems; however, despite the availability of high-speed, large memory digital computers , the solution to a significant three -dimensional problem is by no means trivial. It is unfortunate that the results reported here by Jones are invalid. Jones discusses a model in which a three-dimensional island lies off a linear coastline where all the interfaces lie in the coordinate planes in a Cartesian system. A downward plane em wave polarized with the electric field parallel to the linear coastline, and two of the islands coast, is incident downward. This, of course, requires that the incident electric field is perpendicular to the other faces of the idealized Cartesian island. The significant equation used by Jones for his finite difference calculations is [ ] where n2 = sµ? . is the conductivity, µ=µo is the permeability of the appropriate medium, and w is the angular frequency of a Fourier component of the incident field. We see that the displacement current term is omitted, which is an excellent approximation for the parameters of interest in this model. In the similar equation for the y- component of the diffusion equation, the same considerations which we are about to discuss are equally valid. It can be seen from the equation that the field components are related and thus any errors introduced will be propagated into all three components. The difficulty arises when Ex or E is perpendicular Y to one or other of the surfaces of discontinuity in s. The continuity of current at the air-earth interface (upper surface), e. g., jy, requires

Jan 1, 1973

By Arthur L. Murray

"During recent months much criticism as to the efficiency of mine labor has been heard from various, sections of the country. No doubt much of this criticism has been well founded. The present lack of efficiency and of stability is due primarily to a spirit of restlessness and partial irresponsibility engendered during the transition from war conditions to peace time conditions. This spirit or unrest not only among the laboring classes but in every branch of the human family following a period of intense nervous tension in a nation appears to be a natural sequence of war and beyond the control of man. This condition will gradually disappear, and the majority of our people will again assume their natural order of living, but labor will for a considerable period be sensitive to these influences, whether they be exerted for good or for evil. Employers of labor should take cognizance of this fact and bend every effort towards the development of measures that promote efficiency and permanence of the working force.Labor efficiency depends upon many and varied factors. Some of these factors as applied to mine labor are briefly enumerated in the following paragraph:Selection and Placement of Manpower:In the selection of men the two main considerations are physical ability and adaptability. The laws of mechanics should be applied in the selection of men as in the selection of machinery. If a machine is required for a certain class of work, the type of machine known to be mechanically fit for such work is selected. Likewise, men should be selected with regard to their physical and temperamental fitness for the kind of work expected of them."

Apr 1, 1920

By Mark L. Chatman

This report presents an economic mineral assessment and Inventory of mines and prospects In the approximately 176,000-acre Patagonia Mountains-Canelo Hills Unit of Coronado National Forest. Deposits or areas most likely to experience future development are characterized in terms of their economics, based on data acquired by the author from a variety of sources, and supplemented by USBM field data collected by other workers in 1990 and 1991. Numerous mine maps, rock-chip sample assays, and detailed descriptions of mine and prospect sites are in this report and appendixes. Heavy but sporadic mining, mainly between the 1850's and 1950's was nearly all confined to the Patagonia Mountains. High-grade sulfide veins, replacements, and skarn deposits accounted for most of the production, which included large quantities of zinc, lead, copper, and silver, and considerable quantities of gold. Small Quantities of molybdenum, manganese, tungsten, and placer gold have been mined. Most of the traditionally mined metalliferous sites will not see future activity due to the low tonnages present and removal of most high-grade rock. Possible future development areas include copper porphyries and breccia pipes; most are too deeply buried for current development. Localities where similar deposits may be concealed are identified.

Jan 1, 1994

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930

By Lulie H. Crump

U.S. supply and demand data for dry natural gas by source, form, and major consuming sectors--within and between States and defined regions--were tabulated for the years 1960 and 1965. State-by-State quantitative data are provided for the natural gas industry that can be arranged into regional groupings and used to determine regional flow patterns. The tables show the derivation of the total supply of gas available for consumption from total marketed production. The tables also report the distribution of the supply among the major consuming sectors (household and commercial, industrial, transportation, and electricity generation, utilities). The summarized data show an increase in the absolute demand for natural gas in all regions for the period 1960-65, although the relative posit ions of the various subregions, with respect to national consumption, remained about the same. To enable comparison of data on dry natural gas with data on other energy sources, quantities in terms of million cubic feet were converted to British thermal unit (Btu) equivalents.

Jan 1, 1969