Search Documents

By D. R. Torgoson, Th. G. Sahama

"This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2siO4 and MgSiO3-FeSiO3 and gives the results of a thermodynamic attack on the problems of stability end parageneses.. Although some data are lacking satisfactory agreement with mineralogical and petrological observations is indicated.The use of thermodynamic methods in mineralogy and petrology has been rather limited, because accurate thermal data, especially for the more complicated and more important rock-forming minerals, have been too scanty to permit any systematic application to problems in those fields. It is, nevertheless, a fascinating task to investigate to what extent the mode of occurrence and the stability relations of the minerals and mineral parageneses, as revealed by petrological and mineralogical observations, agree with predictions of thermodynamics. At the present stage of development calorimetric data are needed for most of the abundant silicate minerals.Measurement of the heats of solution in hydrofluoric acid of minerals in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 affords a ready means of obtaining their heats of formation from the oxides. Combination of such data with entropy and heat-capacity values gives a means of obtaining free energies of formation from the oxides, which, in turn, are connected di¬rectly with stability and paragenoses.The two silicates of magnesium, Mg2SiO4 and MgSi03, occur as rock-forming constituents as forsterite and clinoenstatite or enstatite. The orthosilicate (forsterite) forms a series of isomorphic mixtures with ferrous-orthosilicate (fayalite). The continuity of this series, suggested by petrological observations, has boon proved experimentally by Bowon and Shairer.4/ The present work shows that those minerals constitute a series of perfect solid solutions - that is, a series of solid solutions for which heats of formation from the individual pure silicates, Mg2Si04 and Fe2SiO4, aro negligibly small.The metasilicates of magnesium and iron also form an isomorphic series. However, this series differs from the forstorito-fayalite series in the fact that the most iron-rich mixtures, between about En10Fs90 and pure Fs, appear to be unstable with respect to the paragenesis iron-rich olivine plus quartz. The supposed instability of pure FeSiO3 as a crystalline compound, at least at high and at moderate temperatures, is remarkable, as no crystal struc¬tural reason for such instability is apparent. The present work indicates, also, that these minerals form a perfect series of solid solutions and throws additional light on the instability question.In the following, the samples used in this investigation will be described. For each of the natural olivines and orthopyroxenes, with the exception of sample L, a chemical analysis was made of the purified and actually used fraction. All the analytical work was carried cut by Oleg v. Knorring, and the specific gravity determinations, by moans of a pycnomctcr, by Oiva Joensuu, both of the University of Helsinki, Finland. The determinations of the optical properties were made by Mrs. Toini Mikkola, of the Geological Survey of Finland."

Feb 1, 1949

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931. The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results of other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time each sample was taken will also be reported.

Jan 1, 1932

By Carl R. Peterson

Development of reliable, portable, low headroom, hard rock crushers would improve the efficiency of most currently operated conveyor systems and make it possible to bring conveyor haulage closer to the face, thus eliminating expensive rock rehandling procedures. A crusher that could be easily moved would permit the more widespread use of lower cost haulage systems, such as conveyors, to transport the ore out of the mine. Such crushers would be installed close to the working areas, resulting in an optium haul from the face to the dump location. A recent contract study by Rapidex, Inc., "Application Study of Portable Underground Hard Pock Crusher" (USBM Contract No. J0265006) provides a survey of industry needs in portable underground crushing, together with conclusions and concepts as to specifications and type of crusher required to serve the greatest number of operations. To fill this need a three phase program has been undertaken by the Bureau of Mines: Phase I - Design: Phase II - Construction and Testing, and Phase III - Production Underground Test. This report covers Phase I only, and includes the complete engineering design and specifications of the Rapidex Rotary Jaw Crusher conceived in the earlier "Applications Study". Also included are the design, construction, and testing of a quarter-scale functional model, utilizing three different types of rock and two different crusher feeder systems.

Jan 1, 1978

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment: including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that arc recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel al the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

By Leonard F. Heising

At the Groveland mine iron ore is mined by open-pit methods and concentrated by means of spirals and flotation. A brief history of the mine and its early development is given. The ore deposit is described, with emphasis on those physical characteristics that affect the choice of mining and milling methods. Development and mining, which include breaking ground, loading, transportation, engineering, and operating control, are explained, and the milling method is described Mining and milling costs are given in percent of total cost.

Jan 1, 1963

By J. R. Thoenen

During 1928 questionnaires covering the calendar year 1927 were sent to over 1700 quarries: producing stone for purposes other thaw cutting to dimension. These inclined producers of stone for limn burning; cement manufacture, rip rag, and crushed stone. The various rinds of stone represented were limestone, trap rock, sandstone, granite, and marble. Replies received from limestone producers prior to November, 1928, were compiled into tables and published in February, 1925, as a preliminary report (Bureau of Mines Report of Investigation 2911).

Jan 1, 1930

By C. W. Lee

"Introduction of diesel engines in underground mines may generate severe health hazards associated with exhaust contaminants. One of the most important parameter in determining the optimal air quantity for hazard reduction is the exhaust dispersion. Through analyzing the exact solution of the diffusion equation and its approximation by finite difference method(FDM) , this paper aims at doing a fundamental research to find an efficient dispersion model suitable to the domestic mines. Diffusion coefficients are likely to be small in the underground airways with high ventilation resistance. This makes concentration profiles similar to the convection-based step functions. It is the case for fixed as well as moving engines. Concentration estimation by exact solution is almost impossible in the case of either a single engine moving at a variable speed or the existence of multiple engines. Application of FDM to the diffusion equation including turbulent dispersion results in the various problems; unstable concentration profiles depending on the engine location, nuctuating concentrations near the engine, and overestimation of the dispersion region of which error grows with waning diffusion coefficient.Convection-based dispersion model is found to fit well for dynamic simulation of exhaust dispersion from multiple diesel engines in the airways showing low diffusion coefficients. Its suitability is more likely in the regions with frequent equipment passage. Published"

Nov 1, 1995

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By R. V. Higgins

This report presents computer instructions for calculating the performance of three-phase flow of gas, oil, and water. The calculated results for an illustrative example are presented. The example is the waterflood of a reservoir containing free gas in the reservoir as a result of the partial depletion of the oil by the expansion of the gas initially in solution. The flood pattern for the example is a 5-spot.

Jan 1, 1967

By Terry P. Medhurst, Stuart A. MacGregor, Peter J. Hatherly

In addition to fractures and joints, compositional factors and bedding influence the strength of clastic sedimentary rocks. Rock mass rating schemes must therefore consider all of these factors. In this paper, a rating scheme for clastic sediments based on geophysical measurements is described. Geo-physical logging allows an approximation of rock com-position to be obtained and an assessment of bedding frequency and laminations. Velocity measurements incorporate the effects of fracturing. The rating requires scores for the intact rock, bedding/cohesion, and defects. These are combined to yield a Geophysical Strata Rating (GSR). Determination of the GSR is objective and repeatable. GSR values are typically between 20 and 80 and can be related to the Coal Mine Roof Rating.

Jan 5, 2007

By Eugene H. Skinner

The 7-mile Flathead Tunnel, located in the central Salish Mountains of northwestern Montana, was constructed between 1966 and 1969, With the contract awarded April 19, 1966, drill and blast tunnel excavation began September 30, 1966, and was completed June 21, 1968, in 488 tunnel-driving days, Peak advance was 66 feet per day. On June 27, 1969, all tunnel concrete lining was completed. Average wall and arch concrete placing rates exceeded 1,700 cubic yards daily, with nearly half of the concrete placed during a severe winter season. Major cost savings in concrete tunnel lining were achieved through a value engineering clause in the contract. Achieving consistent results and high rates of placement in concrete lining ranked equal to ground control in overall tunnel problems. Ground control problems exceeded expectations and were of continual concern throughout excavation, One support collapse in the tunnel and one portal slide condition developed during construction. Critical surface geologic exposures were largely obscured; only a portion could be accurately projected underground, An instrumentation program to gather basic data on rock defamation near the heading face for support purposes was a pioneering effort. The Flathead Tunnel was placed in service on November 7, 1970.

Jan 1, 1974

By S. R. Droes

The U.S. Bureau of Mines investigated calcium fluoride (CaF2) assisted sulfuric acid (H2S04) leaching as an alternative to the melting-quenching procedure to obtain Mn from domestic manganese silicate resources. Pyroxmangite [(Mn, Fe) Si03] ore containing, in percent, 34.4 Mn, 22.8 Si, 2.6 Ca, and 1.3 Fe was leached in a 500-mL resin kettle. Ninety-six percent of the Mn was extracted under conditions of 330 g/L ore, 245 g/L H2S04, 35 g/L CaF2, 90' C, and 2 h. To incorporate electrowinning in recovering Mn, the ore was leached with a simulated spent anolyte solution containing, in grams per liter, 12 Mn, 140 H2S04, 130 (NH4)2S04 (ammonium sulfate), and 5 CaF2. Manganese extraction of 92 pct was achieved from 130 giL ore leached at 90° C in 3 h. The Fe, silica (SiOJ, and other impurities were precipitated from the pregnant solution by neutralization with ammonia (NH3). Manganese of greater than 99-pct purity was deposited at a cathode current density of 50 mA/ cm2 at 30° C, with a current efficiency of 65 pet in a two-compartment cell. A flowsheet was proposed for the leaching and electrowinning procedure.

Jan 1, 1990

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By Robert M. Doerr

In a process being investigated by the Bureau of Mines for recovering alumina from domestic nonbauxitic resources, calcined kaolinitic clay is leached with hydrochloric acid. Iron impurity in the clay is coleached and is removed in a solvent extraction step prior to crystallization of aluminum chloride hexahydrate, which is subsequently thermally decomposed to alumina. The FeCI3-HCl stripping liquor from the solvent extraction step is unsuitable for discharging to the environment; furthermore, economics requires recovery of the contained chloride values. In the present research, it was shown that the stripping liquor can be reacted with calcined clay to yield AlC13 in solution, plus precipitated iron oxides, residual silica, and unreacted excess clay as mixed solids. For the recovery of the AICl3 solution, the slurry could be separated or returned to the clay-HCI process stream at the solids washing step that follows primary HCI leaching of the clay. For the range 20° to 99° C, the time (t) (103 sec) required to react the waste liquor with excess clay, for essentially complete iron precipitation, depends on the absolute temperature (T) chosen, according to the expression t = e[(9.000/T) -23.5J. (1) Alumina was tried as a reagent alternative to clay but was not very effective, even under pressure and at high temperatures.

Jan 1, 1982

By J. E. Murphy

A method is being developed by the Federal Bureau of Mines for recovering lead metal from galena without the generation of SO2. Lead chloride is obtained by leaching lead concentrate at a temperature of approximately 100° C with FeCl3 solution: PbS + 2FeCl. " PbC1 2 + 2FeC1 2 + S. Electrolysis of the PbCI 2 product in a fused-salt bath results in deposition of molten lead metal at the cathode and evolution of chlorine at the anode. The chlorine can then be absorbed in the spent leach solution to regenerate FeCl3 for recycling. Optimum electrolyte composition was a PbC12-LiCl eutectic containing 7.6 wt-pct LiCl. The PbCl2-NaCl eutectic also proved satisfactory. Electrolysis in the PbCl2-LiCl bath at 450° C yielded 99 pct current efficiency at a current density of 5 amp/in2 with an energy requirement of only 0.24 kW-hr/lb metal produced. This compares with 98 pct current effi¬ciency and 0.26 kW-hr/lb metal produced for the PbCI2-NaCI bath. A typical lead deposit contained less than 100 ppm total detectable metallic impurities. At the low temperature employed for electrolysis, there was essentially no vaporization of Pb or FbC12.

Jan 1, 1974

By McHenry Mosier

This is the fourth progress report in the series on the use of detachable rock-drill bits in the metal mines of the United States. It contains comparative statistics and costs or drilling at eight mines not reviewed in previous reports, comparison of the use of detachable bits at small mines and large mines, a discussion on the life of drill rods, and general conclusions derived from an analysis of the rock-drilling practice at all the mines investigated on this survey. This paper completes the descriptions of operating practice in rock drilling at individual mines. Data on drilling practices at 28 mines are given in appendices I and II and drilling costs are shown in appendix III. Research in the fundamentals of rock drilling, including the use of detachable bits, has been undertaken by the Bureau of Mines in its testing adit at Mount Weather, Va. Reports on the progress off this investigation will be issued when results warrant their publication.

Jan 1, 1937

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964