Search Documents

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By E. Morrice

High-purity neodymium, praseodymium, and didymium (a cerium-free mixture of light rare-earth elements) were prepared by electrolysis of the oxides in a medium consisting of the respective rare-earth fluorides and lithium fluoride. The metals were electrodeposited in the liquid state and collected as nodules on a skull of frozen electrolyte. Cells were operated from 1,000° to 1,100° C. The requisite temperature was maintained by passing alternating and direct currents through the bath. Graphite was used for the anodes and tungsten for the cathode. The metal products contained <0.02 percent each carbon and oxygen and <0.025 percent tungsten as major impurities. Analysis of typical didymium metal nodules showed an approximately twofold enrichment in neodymium and praseodymium over their respective concentrations in the cell feed. The lanthanum content of the metal was about one-half its content in the oxide.

Jan 1, 1967

By R. L. Grayson, W. E. Wallace, J. W. Stephens, M. D. Attfield, P. S. Brower, V. Vallyathan, M. J. Keane, J. C. Harrison

Pure respirable quartz is a known pathogenic agent for lung disease. However, for mixed dusts, neither mineralogical nor in vitro cytotoxicity assays unequivocally predict the contribution of quartz to their pathogenic potential.First, although Coal Workers' Pneumoconiosis (CWP) and Progressive Massive Fibrosis (PMF) prevalence have been found to correlate with total respirable coal mine dust exposure, and with coal rank (Attfield and Morring, 1992), epidemiological studies generally have not found the quartz component of coal mine dust as measured by X-ray diffraction or infrared spectroscopy (each of which essentially measures the mass-percent quartz in a bulk sample) to be clear predictors of CWP prevalence or incidence (Walton et al., 1971). Second, the properties which distinguish the extreme fibrogenic potential of quartz are not revealed by conventional in vitro bioassay comparison with other silicate mineral dusts. As an example, quartz and kaolin (aluminosilicate) clay in vitro cytotoxicities are comparable for lavaged primary pulmonary macrophages.The studies discussed here address these two anomalies from a general hypothesis that the pathogenic activity of respired quartz particles is associated with properties of, and interactions with, the particle surfaces. One factor in the expression of toxic activity by a particle surface is the biological availability of that surface. Anomalous lack of correlation of disease prevalence with mass percent quartz in exposures to some mixed composition respirable-sized dusts suggests that individual particle surface features, invisible by bulk sample mass analysis, may alter the biological availability of a fraction of quartz particles in a dust. For pure-surfaced mineral particles, the comparably strong prompt membranolytic activities of quartz and kaolin in vitro suggest that upon deposition of such particles in the lung there must be other interactions with particle surfaces which distinguish quartz. This might be due to toxic surface-associated sites specific to silica, or to interactions of other sites on other mineral particles which affect the biological availability of their toxic functional groups. For example, alurninol groups on clays affect the availability or activity of adjacent silanol groups. Surface activities which distinguish quartz pathogenici ty might be manifest in one or more of the sequential interactions upon deposition in the lung; first with the pulmonary surfactant system, then with extracellular and phagolysosomal enzymatic digestive processes, or with subsequent cytotoxic processes.

Dec 1, 1995

By BUREAU OF MINES

PLATINUM

Feb 1, 1922

By Mark L. Chatman

The U.S. Bureau of Mines studied mineral resources of the Dragoon Mountains Unit, Coronado National Forest (54,264 ac), Cochise County, AZ. This study involves literature and field investigations with a focus on mine and prospect sites, which were inventoried and mapped; maps are contained in this report. Rock-chip samples were taken from mineralized zones and from some mine dumps; assays of the 477 samples are in appendixes. Mineral deposits are genetically and spatially related to Tertiary-age granitic intrusive activity. Most metallic mineral deposits are also strongly fault-controlled. Colored marble resources (270,000 st) are valued at approximately $6.5 million, if all were to be developed and sold as landscaping material in the form of-marble chips. However, with current demand, it is unlikely that regional markets could absorb all this material. Economic modeling of copper-zinc-silver skarns suggests none would be profitable to mine and capitalize at early 1993 commodity prices, mainly due to the small estimated size of the deposits (30,000 st to 40,000 st maximum). In the entire Unit, 140,000 st of inferred subeconomic skarn resources were estimated by USBM on five different skarn trends; measured subeconomic resources are negligible. Exploration by industry, 1992, was small-scale (on 2 skarn trends and 1 auriferous fault zone).

Jan 1, 1993

By H. C. Carpenter

Lignite tar made by low-temperature Lurgi-Spülgas carbonization of North Dakota lignite was hydrocracked in single-pass, fixed-bed operation at 3,000 pounds per square inch over cobalt molybdate catalyst to produce gasoline, and at the same pressure, over zinc chromite catalyst to crack the high-boiling phenolic compounds to low-boiling phenolics. Hydrocracking the raw tar or the creosote-oil fraction from the tar over cobalt molybdate removed most of the oxygen, sulfur, and nitrogen in the forms of water, hydrogen sulfide, and ammonia, and produced gasoline yields from 31 to 59 volume-percent. The gasoline fractions contained from 0.1 to 7.7 volume-percent tar acids, but tar-base percentages were too low for reliable measurement; removal of these materials with dilute caustic and acid solutions also reduced the sulfur and nitrogen to 0.01 weight-percent or less.

Jan 1, 1963

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

By W. W. Graff

This paper describing the mining practices at Mine, No. 4 on the Marquette range, Michigan, is one of a series of articles on mining methods and practices in various mining districts in the United States. Mire No. 4 is located in the Swanzy district, in the southern end of the Marquette range, about 3 miles from Gwinn, Mich. The Swanzy district is an isolated ore-bearing formation, and Mine No. 4 is at the extreme southeastern end.

Jan 1, 1930

By I. AITKENS

The basic mining law of Cuba is contained in the basic Spanish mining decree having the effect of law December 29 , 1868. This legislation has remained substantially unchanged , with the exception of a few minor administrative changes made by the present Government . These changes provide for the register of mines , oil wells , and operations of such nature , and also provide for the keeping of records showing the value of minerals taken out . By Royal decree of April 17 , 1883 , the law of mines enacted for the Peninsula ( Spain ) on July 6 , 1859 , and the General Bases of December 29 , 1868 , were declared in force in Cuba . In order to encourage the mining of iron org , in 1883 the Crow of Spain issued a royal decree to the following effect.

Jul 1, 1931

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Guatemala has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Oct 1, 1929

By R. R. Sayers

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try , if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By G. L. Fitzpatrick

Future applications of seismic holography to "seismically transparent phase objects," such as rock inclusions, fracture zones, liquid-filled cavities, etc., will require techniques to improve the poor image contrast generally characteristic of these objects. Although conventional phase-contrast enhancement techniques could be used, these methods involve additional optical elements such as quarter-wave spatial filters. Owing to the anticipated practical difficulties of properly alining such optical devices and properly locating poorly defined image planes and filter planes, this approach is not considered to be well-suited to the case of seismic holograms and their laser reconstructions. Results similar to those achieved with spatial filters may be obtained without filters by specially processing the seismic hologram data. The new process, which is an extension of Gabor&apos;s subtraction holography, achieves an improvement in contrast by an interferometric technique. The process involves adding a ?before" hologram without an object present to a 90° phase-shifted "after" hologram with the object present. Then, the combination is reconstructed with a laser or by computer. Not only is the image contrast improved in such processed holograms, but the images are also phase-contoured. In general, the latter feature is not to be expected when conventional phase-contrast enhancement techniques are employed. The new technique is experimentally verified by examining computer-generated synthetic seismic holograms rather than by examining actual seismic field data. However, results of this study are directly applicable to real seismic data and should prove useful in future applications of seismic holography.

Jan 1, 1973

By C. L. Klingman

The Bureau of Mines tested eight commercially available, activated charcoals experimentally to compare the following characteristics: capacity for adsorption of nitrogen at 77° K and 170 atmospheres&apos; pressure, surface area, carbon tetrachloride adsorption capacity, hardness, and density. The nitrogen adsorption test was devised to simulate plant conditions occurring in the final step of purification in Bureau helium faciliti.es. The remaining tests were patterned after empirical acceptance tests that are widely used throughout the adsorbent industry. Surface area and carbon tetrachloride adsorption correlated well with nitrogen adsorption. The samples with low density generally had better adsorption qualities than those of higher density. The carbon tetrachloride test appeared to be the most practical for selecting a charcoal to be purchased, but an attrition, or hardness test should also be run to be sure the charcoal will not crumble in use.

Jan 1, 1966

By G. W. Jones

Among its investigations into the prevention of waste in production and use of oil and gas, the Bureau of dines has made considerable study of the efficient utilization of gasoline and by-product distillates in motors, this being done chiefly by measuring and analyzing the exhaust gases therefrom. A number of reports3 of a highly practical nature have been published and are available on this subject. The results of these tests have shown that the average motor vehicle wastes approximately 30 per cent of the heat value of the fuel used, as incomplete combustion products - carbon monoxide, hydrogen, and methane, These unnecessary large heat losses are mainly due to improper carburetor adjustment, and by proper¬ly adjusting the carburetors for maximum power and efficiency a large part of this heat loss can be eliminated. This in turn results in an increased mileage per gallon of fuel used.4

Jan 1, 1924

By L. Mark Irwin, R. A. Marsyla

The objective of this laboratory investigation was to develop a mattesmelting process for the recovery of copper from industrial smelter dusts . Experimentation was conducted on three samples of Cottrell precipitator dust from a northern Michigan smelter with variations in the following conditions : Temperature , charge composition , pelletization , and moisture content . Based on chemical analyses of the furnace slags , poorest recovery of copper was effected in smelting dry charges regardless of composition . Some improvement was noted with uniformly moistened charges and still more with pelletized (but dry) mixes , but best results were obtained from smelting moist , self - fluxing pellets . Under favorable conditions , experiments yielded furnace slags with an average copper content of only 0.15 percent , which is well below that of industrial copper reverberatory slags .

Jan 1, 1963

By H. B. Brunot, L. C. IlsLey

The design , construction, inspection , and test for permissibility of a storage- battery locomotive outfit in accordance with the requirements of Schedule 15* represents a large amount of work, first on the part of the locomotive manufacturer and secondly on the part of the Bureau of Mines . Detailed information of the first investigation under the schedule is presented here . This investigation covers the inspection and test of a storage- battery locomotive manufactured by the Geo . D. Whitcomb Co. , Rochelle , Ill . , to which Approval No. 1500 was assigned ,

Feb 1, 1923

By J. E. Berg

This paper3 describing the mining methods at the Page mine operated by the Federal Mining & Smelting Co., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Page mine is the most westerly of the producing lead-silver-zinc mines in the Coeur d&apos;Alene mining district of Idaho, being situated 5 miles west of the city of Kellogg and at an elevation of 2,677 feet above sea level. It may be classed as one of the new active producers, of the district and owes its present activity largely to the development of floatation.

Jan 1, 1930

By H. C. Miller

For nearly a score of years the American petroleum industry has faced the problem of maintaining its economic structure while oil -producing potentialities greatly exceeded the increasing market demand for oil and its products . However , the combination of maximum civilian demand with rising defense requirements caused an all - time peak in crudeoil production in the latter half of 1941 , with a daily production (as estimated by the Bureau of Mines ) of 4,139,000 barrels in December - an increase of 16 percent over the daily production of 3,573,000 barrels in December 1940. In the event of a long war , a continuing , steady, and adequate supply of petroleum and its products for military and required civilian needs is essential, and the efficiency of recovery of oil from natural underground reservoirs will have to be maximum. Whereas it may not be possible to increase production in some fields , the output from others may have to be drawn at a much faster rate than formerly . More than 10 years ' experience in operating oil fields under proration control has demonstrated to petroleum engineers that some of the efficiency of recovery of oil from reservoir sands and rocks is sacrificed if the oil and gas are withdrawn at too . rapid a rate . As petroleum is an irreplaceable natural resource for which suitable substitutes probably will not be available in desired quantities for many years , any producing method that jeopardizes the quantity of oil that may be recovered from underground reservoirs must be considered at this time of declared war against aggressor nations as conflicting with the best interests of national defense . At best, the efficient recovery of oil is a complex problem . It involves not only a knowledge and application of the fundamentals of fluid flow through porous mediums, but the sources of energy responsible for the movement of oil and gas through reservoir sands and porous rocks to wells must be known to determine the best practices for extracting these hydrocarbons . Reservoir energy is of two kinds - (1 ) water under hydrostatic head underlying the oil in the extraneous parts of the reservoir system and ( 2 ) natural gas under pressure as "free " gas in the reservoir or in solution in the oil . Inasmuch as the efficiency of oil recovery depends largely on the manner in which reservoir energy is used to move oil through reservoir sands and porous rocks to wells , optimum practices for withdrawing the oil cannot be determined until it has been established that the oil in the reservoirs is being forced to wells by an internal gas expansion, by a natural water drive , or by a combination of gas expansion and water drive . There is a fundamental difference in the performance characteristics of gas - expansion and water - drive reservoirs . In a strictly gas - expansion reservoir the energy available to move oil and gas through the porous formations to wells results solely from gas pressure , which is maximum when the reservoir is tapped by the first well . Pressures decline as oil and gas are withdrawn ; consequently, the energy available for moving oil and gas through the oil - bearing formations to wells decreases with production . Curtailing the oil - production rate or shutting in gas - expansion reservoirs entirely will not act to replenish energy previously used in the production of oil and gas ; in their operation , therefore , it is especially important not to waste reservoir energy - the production of oil with high gas : oil ratios will be reflected in lower ultimate recoveries of oil .

Apr 1, 1942

By A. B. Cecala

The Bureau of Mines has developed a pallet loading dust control system designed to lower the dust exposure of workers during the bag stacking process at mineral processing facilities. The system makes bag stacking much easier because the pallet height remains constant throughout the entire bag stacking cycle through the use of a hydraulic lift table. The system uses a push-pull ventilation technique to capture the dust generated during bag stacking. A low-volume, high-velocity blower system operating at approximately 150 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-in air jets (approximately 1,200-ftjmin velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they entrain the dust generated during bag stacking. The exhaust ventilation system pulls approximately 2,500 cfm of air and dust through the exhaust hood. This exhaust air can then be dumped into a baghouse ventilation system, or filtered before being discharged outside the mill. During a laboratory evaluation, a 70-pct dust reduction was recorded for the bag stacker. The system was then evaluated in an actual working environment. The first field evaluation was performed at a silica sand operation in which one worker performed the entire loading and bag stacking process. This worker&apos;s dust exposure was lowered 76 pet when using the new pallet loading system. The second field evaluation showed only moderate dust reduction, but this was mainly attributed to an overriding problem associated with background dust and the cleanliness of the bags. From both the ergonomic and production standpoint, the system was well received by both the workforce and plant management.

Jan 1, 1988

By J. M. Kuchta

The Bureau of Mines used laminar hot air jets of l/8- to 3/4-inch diam-eter to determine the hot gas ignition temperatures of various combustible vapor-air mixtures. The combustibles were n-hexane, n-octane, n-decane, a hydrocarbon jet fuel (JP-6), and an adipate ester aircraft engine oil (MIL-L- 7808). Minimum ignition temperatures occurred at a fuel to air weight ratio of about 0.5 and were not greatly sensitive to variations of fuel concentra¬tion. Moderate variations of jet velocity also had little influence on these ignition temperatures. However, these temperatures decreased with increase in heat source dimensions (jet diameter). The hot gas ignition temperatures of the combustibles were not necessarily much greater than corresponding autoignition and wire ignition temperatures when the size (,F the heat source and the ignition criterion were the same.

Jan 1, 1966