Search Documents

By Lester M. Adams

In 1980, the Bureau of Mines surveyed a group of mine seals in Randolph County, WV, to evaluate their effectiveness for reducing toxic pollutants in mine water discharges. The survey focused on 11 block wet mine seals, but mine seals of several other types were also examined. The seals were installed in 1966 and 1967 in abandoned drift portals by the Federal Water Quality Administration (FWQA), a predecessor of the Environmental Protection Agency (EPA), in cooperation with the Bureau of Mines and other Federal and State agencies, in a project known as Elkins Mine Drainage Pollution Control Demonstration Project. The seals were designed to prevent air from entering the mine portals while allowing mine water to flow out. It was believed that by preventing air from entering inactive or abandoned mines, the formation of toxic pollutants and acid mine drainage (AMD) could be reduced. Evaluation of the seals was based on water flow measurements, water analyses, and visual observations. The Bureau's 1980 data were compared with past data collected by the EPA. Several leaks and failures were observed in the clay seals, as evidenced by apparent blowouts and the absence of vegetation where the mine water surfaced. Analyses of the 1980 data indicated some improvement in the quality of water discharged from many of the wet air seals.

Jan 1, 1984

By Michael Sokaski

A dense-medium cyclone pilot plant was built to clean 112-inch to 0 size coal. This pilot plant does not require the removal of the extremely fine material (usually minus 1/2-mm) from the feed, which is necessary in conventional dense-medium cyclone plants. The essential difference between conventional cyclone plants and the pilot plant is in the medium-recovery system. The latter uses a combination of sieve bend screens, classifying cones, and magnetic separators for medium recovery. Eight tests were run in the pilot plant at a feed rate of 5 tons per hour with four different raw coals and one crushed jig middling product. Sharp separations were obtained as indicated by an average error area of 27 and probable error of 0.047 for the 112-inch to 200-mesh size range. Magnetite loss averaged about 2.5 pounds per ton of feed. The influence of several factors on cleaning performance of the cyclone was investigated. The diameters of both the overflow and underflow orifices were found to be important for optimum cleaning performance, but these diameters could vary over a wide range without serious effect; however, if this range was exceeded, cleaning performance deteriorated. Better cleaning performance was obtained when the cyclone inlet pressure was increased from 9 psig to 13 psig. The size of the magnetite particles in the medium was found to have a substantial effect, and the best cleaning results were obtained with grade B magnetite. Demagnetizing the magnetite in an effort to decrease the effective particle size did not improve cyclone performance.

Jan 1, 1963

By Michael P. Hardy

The report described improvements and applications of the Hybrid Computer facility. Improvements implemented under U.S.B.M. Contract H0252035 included expansion of the capability to model nonlinear seam behavior, installation of a color video output display monitor, and further development of software capabilities. To demonstrate the capability of the system, firstly, the influence of nonlinear seam behavior response to the occurrence of coal mine bumps was fully investigated and secondly, the effect of improper mining sequence on bump occurrence was demonstrated. In addition, the system was applied to the analysis of a series of practical coal mine problems. Mines in three coal seams were analysed to investigate the parameters which contribute to the occurrence of coal mine bumps.

Jan 1, 1977

By C. C. Anderson

"While conducting investigations in connection with the helium program of the Bureau of Mines, the Cryogenic Laboratory has improved an apparatus for the rapid and accurate determination of the helium content of natural gas and gaseous mixtures derived from that source. The separation of helium is effected by the use of activated coconut charcoal which, when cooled to liquid-air temperatures, absorbs the nitrogen and other constituents of the gas, leaving the helium in a. spectroscopically pure state. This absorptive property of activated charcoal was discovered- by Dewar3/ in 1875. Several years later, while conducting their original researches on helium in natural gas, Cady and McFarland employed the charcoal method for the absorption and removal of the common constituents of natural gas and constructed an efficient apparatus in which this operation could be effected.4/ Shortly after initiating the government's helium activities during the World War period, the Bureau of Mines adopted, with Minor modifications, the Cady and McFarland apparatus and method of analysis. Seibel.5./ described this modified apparatus and method of procedure as part of a publication on helium-bearing natural gas. Subsequently, the Bureau's apparatus for helium analysis has been simplified and improved to facilitate more rapid and positive operation. The apparatus and method of procedure now being used by the Bureau of Mines Cryogenic Laboratory arc described in this paper.The personnel of the Bureau of Mines Cryogenic Laboratory has improved and brought the helium apparatus described herein to its present state of perfection. The writer's contributions have been-of minor importance, and he wishes to give the various members and former members of the laboratory staff full credit for the improvements they have made. He also desires to express his appreciation for suggestions and criticisms offered during the preparation of this paper to the following members of the Petroleum and Natural Gas Division, Bureau of Mines, which now includes the Amarillo Helium Plant and Cryogenic Laboratory: H. A. Cattell, chief engineer; C. W. Seibel, supervising engineer of the Amarillo Helium Plant; W. M. Deaton, chemist-in-charge of the Cryogenic Laboratory; and H. S. Kennedy.The quantitative determination of helium in a gaseous mixture is accomplished by the removal of the other constituents from the sample, either by chemical or physical Means, leaving only the helium which can be measured directly. Chemical methods, when applied to natural gas, require the burning of the hydrocarbons in oxygen, the, absorption of the resulting carbon dioxide in a caustic solution, the removal of the excess oxygen in a suitable solution such as an alkaline pyrogallate, and the elimination of nitrogen by sparking or by combination with hot calcium or magnesium.. Such procedures are very slow and tedious compared with the physical method which employs the absorptive property of activated charcoal to effect the separation of the other constituents from the helium."

Jun 1, 1934

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

By F. E. Brantley

Research was undertaken by the Bureau of Mines to assess the technical feasibility of smelting cement-copper precipitate in an electric furnace to produce commercial-grade copper. The blister-grade copper produced in smelting was refined by gaseous oxidation and reduction methods to rive a product equal in quality to fire-refined copper. The cement copper used in the study was typical of the material produced in commercial operations. The sample product was received in a partially oxidized state and analyzed 77.5 percent Cu, 3.4 percent Fe, 0.8 percent Pb, 0.05 percent Ni, 0.6 percent Sn, and 0.9 percent S. Smelting tests were made on the precipitate using laboratory-size induction and electric-arc furnaces. Three types of furnace linings were tested during, the investigation: Carbon, including graphite; clay-graphite; and silicon carbide. Although all proved satisfactory, either carbon or graphite was preferred because of their superior refractory properties and low permeability to molten copper. Copper recoveries in the induction and arc smelting tests averaged 92 percent in commercial-grade metal assaying 99.8 percent copper. Refining the molten copper by oxidation and gaseous reduction or by chlorine lancing increased the purity to plus 99.9 percent.

Jan 1, 1961

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By R. K. Guthrie, H. B. Hill

"INTRODUCTION The Rodessa oil field in Marion and Cass Counties, Tex., Miller County, Ark., and Caddo Parish, La., was discovered in August 1930, when a well drilled to a depth of 5,506 feet in Caddo Parish, close to the surface trace of the Rodessa fault, produced gas in commercial quantities. During the next 5 years 21 gas wells were drilled, and a large reserve of natural gas was developed in the high part of the Rodessa structure underlying the Massive Anhydrite member of the Glen Rose formation.In July 1935 oil was discovered on the flank of the structure when a well drilled to 6,048 feet also in Caddo Parish, was completed as an oil well. The discovery of oil in the Rodessa structure initiated art intensive development program of more than usual interest to geologists, engineers, and operators in the petroleum and natural-gas industry. The complex nature of the different reservoirs, the large volume of ""free"" gas under high pressures and temperatures in the upper part of the reservoirs, and the high gas:oil ratios of some of the wells during the early production of oil presented many problems the solution of which taxed the ingenuity of those responsible for the development and exploitation of the Rodessa field.Early waste of gas and resultant dissipation of reservoir energy led to State intervention, which brought about effective regulation of the quantity of gas blown to the air. Oil production from wells producing more than 2.000 cubic feet of gas per barrel of oil was restricted, and oil allowables generally were based equally upon acreage and upon reservoir pressures. Consequently, oil-production statistics of the field are closely associated with gas:oil ratios and reservoir pressures.The primary object of this report is to present factual and statistical data on well performance in the Rodessa field and to show established trends under certain operating methods and practices in high-pressure gaseous reservoirs, which have been carefully developed and outlined by modern technique and exploited under close engineering supervision.The large size of the Rodessa field, it’s fairly well defined gas caps, and a somewhat definite water table in a part- of the oil- and gas-producing region are of special interest and importance in a study of the fluid and energy relationships in reservoirs. Consequently, the results of much of the authors' work in collecting and compiling date are presented in the form of tables, maps and cross sections to show the relative thicknesses of the different oil-and gas-producing members and their permeability and porosity relationships, and, when possible, the variations in stratigraphy are exhibited in cross sections. Results of a detailed analysis of cores from a number of wells also are presented in tabular and graphic form."

Aug 1, 1943

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By G. V. Sullivan, G. F. Workentine

Beneficiation studies were conducted by the Bureau of Mines on three samples of low- grade chromite - bearing material from the Stillwater complex of Montana . The objective of the study was to develop methods for recovering chromite from low- grade materials to improve the domestic reserve situation . Samples were obtained from the three largest deposits in the district , Mouat , Benbow , and Gish . The chromic oxide ( Cr₂ 0 ) content of the ore and of the chromite was about the same in each of the samples . The major gangue constituents ranged from clean olivine in the Mouat sample to such altered minerals as serpentine and talc in the Benbow and Gish samples . Tabling , flotation , high- tension electrostatic separation , and combinations of processes were applied to each ore . Treatment of the Mouat sample ( 9.95 percent Cr₂ 0 ) by high- tension electrostatic separation , a combination of tabling and high- tension electrostatic separation , and tabling with middling retreatment resulted in concentrates that graded 42.8 , 42.0 , and 40.7 percent Cr₂03 at chromium recoveries of 85 , 86 , and 84 percent , respectively . Other techniques were less selective . 2 The Benbow sample ( 7.75 percent Cr₂0 ) responded most selectively to tabling with middling retreatment and a combination of tabling and hightension electrostatic separation to produce concentrates of 40.1 and 39.5 percent Cr₂g with each process having a chromium 2 recovery of 69 percent . Response of the Gish sample ( 8.04 percent Cr₂03 ) to the various concentration techniques was about the same as that of the Benbow sample , but in general , somewhat less selective . A combination of tabling and high- tension electrostatic separation resulted in a concentrate that contained 71 percent The Mouat mine was reopened in 1953 when the American Chrome Co. contracted with the Federal Government to produce 900,000 tons of chromite concentrate . The ore , averaging 20.2 percent Cr₂03 , was treated by tabling to produce a 38.5 - percent Cr₂ O concentrate.

Jan 1, 1964

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By Leon E. Esparza

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 16,927-acre Pryor Mountain Wilderness Study Area (MT-067-206), part of the 3,955-acre Burnt Timber Canyon Wilderness Study Area (MT-067-205), and part of the 4,550-acre Big Horn Tack-On Wilderness Study Area (MT-067-207) to evaluate their identified mineral resources. The Burnt Timber and Big Horn Tack-On study areas contain 3,430 and 2,550 acres, respectively. The three areas are in Carbon County, MT, and Big Horn County, WY, about 13 miles north of Lovell, WY. No identified resources exist in any of the study areas. Bureau of Mines personnel reviewed literature, searched county mining records and examined prospects, claims, and mineralized areas to determine whether identified mineral resources existed. The three study areas are within the Pryor Mountain unorganized mining district. U.S. Department of Energy production records indicate there were 223,000 pounds of uranium oxide (U308) and 236,000 pounds of vanadium pentoxide (V205) produced from 19 properties within the mining district. The average ore grade was 0.36 percent [3,600 ppm (parts per million)] U308 and 0.416 percent (4,160 ppm) V20S. Only the Pryor Mountain study area has current claims, the 50 claims of the S0S group.

Jan 1, 1986

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By M. R. Geer

Three coals from the Wilkes on - Carbonado district of Pierce County , Washington , were subjected to washability analyses to estimate the amount and quality of washed coal obtainable . Because the coals were unusually difficult to clean , the washability examinations were supplemented by table tests , tests in dense - medium cleaning units , and flotation tests . None of the coals could be reduced to the desired 10 percent ash by tabling and the response to flotation by two of them was poor . Dense -medium treatment provided coal of the desired quality , but with the most difficult coal the recovery efficiency was lower than usual .

Jan 1, 1964

By Lowell B. Moon

The Stange and Byrnes Heirs manganese mines, adjoining properties in Bland and Giles Counties, Va., have produced at least 20,000 long tons of concentrates containing 8,000 long tons of manganese. They were selected as the site for a strategic-mineral development project because of the existence of geologic possibilities for extensions of the known ore body. In plan, the long dimension of the ore body parallels the axis of a major anticline. Localization apparently is due to longitudinal and transverse fracturing incident to two-way folding. That the manganese oxides were deposited by downward-moving solutions is suggested by the fact that mineable concentrations are confined to a coarse, porous sandstone under-lain by impervious silt and clay. Bureau of Mines project work began on January 15, 1941, and was completed on April 23. The work sampling the faces of the pit, bulldozer trenching, and churn drilling. Pit sampling consisted of 132 channel samples usually 5 feet long and taken at 20-foot intervals. Seventeen trenches aggregating some 4,500 feet in length were dug by the bulldozer. Trenches averaged 12.6 feet in width and 5 feet in depth. A total of 1,978 feet of churn drilling was done in 33 holes. In preparation for churn drilling it was necessary to construct roads to 21 of the 33 sites. A total of 2,867 linear feet of road averaging 13 feet in width was built.

Jan 1, 1950

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Southern field is part of the comprehensive study of the mine water problem in the anthracite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8, 9, 10, 11, 12, 15, 16, 18).4 Tim Southern field is in Carbon, Schuylkill, Dauphin, and Lebanon Counties, in eastern Pennsylvania; has an area of 200 square miles; is 70 miles long from Mauch Chunk on the east to the Susquehanna River on the west; and is 1 to 6 miles wide. In the Southern field are 37 underground water pools containing 37312 billion gallons of water (5). Most of these pools overflow to the surface because the barrier pillars controlling them are effective under existent, conditions. Abandonment of mines in the Southern field has resulted in the hooding of 34 percent of the field. The largest tonnage of reserves of anthracite lies in this field, where mining conditions are most difficult. Large reserves of anthra¬cite underlie the abandoned mine workings, and before a great part of these reserves can be developed and extracted, the abandoned workings must be unwatered and kept drained (5).

Jan 1, 1953

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. Then enough circulars have been completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed by bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual mines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); ventilation; wage, contract end bonus systems, etc.

Jan 1, 1930

[Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand .for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing2/ relative to the need for the sway, the opinion ms expressed that crude oil held in storage for long periods had lost so much of its gasoline content that he economic significant of total stocks should be discounted materially. Therefore, a primary objective of the survey was to]

Jan 1, 1938