Search Documents

By W. G. Pariseau

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mine in the Coeur d'Alene Mining District of northern Idaho. The present study uses rock deformation measurements to validate and calibrate a geomechanical model of the experimental Lucky Friday underhand longwall (LFUL) stope on the 5,100-ft level of the Lucky Friday Mine, Mullan, ID. The calibrated three-dimensional, finite-element model and measurements of rock mass displacement show a correlation of 0.795. The calibration reduces rock mass modulus to 14 to 17 pet of laboratory values and rock mass strength (with an energy rule) to 37 to 41 pet of laboratory values. This model suggested that stress-related ground control problems would be encountered west of the stope where the vein makes a right-angle turn and then splits. Rock burst activity was concentrated in this area during mining of the LFUL stope.

Jan 1, 2010

By S. L. May

Tantalum and columbium can be extracted from several of their ores or concentrates by chlorination procedures. Direct chlorination of high-grade minerals in the presence of carbon at temperatures between 500° and 800° C will extract up to 99 percent of the tantalum and columbium. Metallurgical beneficiation of low-grade source materials by carbothermic reduction produces a ferroalloy that is amenable to chlorination at a temperature of 500° C. Over 90 percent of the tantalum and columbium can be recovered.

Jan 1, 1965

By Aner W. Erickson

Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.

Jan 1, 1948

By W. W. Adams

In mining coal, the Nation's principal mineral fuel, loss of life has been much lower recently than in earlier years when coal mining contributed so heavily to the industrial-accident death toll in the United States. Particularly notable has been the relatively small number of deaths during the past few years compared with the number that occurred 20 or 30 years ago. Reports received by the United States Bureau of Mines, covering all commercially operated mines that were active during all or any part of the calendar year 1935, showed that accidents during that year had resulted in the loss of 1,242 lives. This death toll, although regrettable, represents a material improvement over the industry's experience during most years prior to 1935, and especially over the industry's worst year, 1907, when 3,242 men were killed. Fewer lives were lost in 1933, when 1,064 men were killed at work, than during any year for which complete figures are available.

Jan 1, 1938

By John A. Breslin

The Bureau of Mines measured respirable dust in coal mines by means of multiple dust samplers worn by persons moving about the mines. The measurements were made primarily to evaluate the effectiveness of certain dust-control techniques; however, for this report, the data have been analyzed to determine the precision of the personal dust-sampling measurements. A total of 68 sets of measurements were available from multiple personal samplers. The measured dust masses were less than 1.0 mg because the sampling times were short. The coefficient of variation calculated from these data was 18.5 pct, compared with coefficients of variation ranging from about 10 to 30 pct, which were calculated from the most precise and extensive data available for fixed-point dust measurements made in coal mines. From this comparison, it is concluded that dust samplers worn by personnel are as precise as fixed-point samplers in measuring respirabe coal dust; the wearing of the samplers by someone moving about a mine does not contribute significantly to the variation in measurements made with these instruments.

Jan 1, 1983

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By William W. Adams

A general increase in employment prevailed in the stone-quarrying industry of the United States during 1941 compared with 1940. Likewise, more accidents occurred to men working in and about the quarries, with the result that the accident-frequency rate for the industry as a whole was higher in 1941 than in the previous year. Reports from operating companies to the Bureau of Mines, covering open and underground quarries, as well as rock-crushing and rock-dressing plants, cement mills, and limekilns at or near the quarries, showed a total of 86,123 men employed and a total of more than 22 million man-days of labor performed during 1941. The total working time of the industry averaged 260 days per man. Measured in man-hours, the volume of work equaled 173 million, an average of 2,011 man-hours per employee.

Jan 1, 1943

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the? Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940, to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By D. W. Frommer

As one phase of a general problem of recovering sulfide slimes, mineral-dressing research was conducted on flotation tailing from the St. Joseph Lead Co., Bonne Terre, Mo., mill to recover a significant portion of the residual, finely divided galena. Production of a high-grade concentrate was not part of the immediate objective. Only a reasonable ratio of concentration of lead sulfide slime was sought, since the problem of upgrading by mechanical or extractive processes would be considered in the later stages of this study. The results show that, from a feed material averaging 0.20 percent lead (about 70 percent finer than 400-mesh), a recovery of up to 45 percent could be effected by flotation in rougher concentrate analyzing up to 6.5 percent Pb. These results were obtained by using larger quantities of various xanthates and sodium sulfide than used customarily in mills. Sodium sulfide, which is ordinarily detrimental to flotation of galena, was beneficial in this case.

Jan 1, 1959

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By Laurance L. Oden

Titanium-enriched smelter slag produced commercially by Quebec Iron and Titanium Corp., Sorel, Quebec, was evaluated as feed material for a process developed by the Bureau of Mines to prepare rutile. Glass-forming agents including P205, B203, and two binary mixtures were added individually to the as-received and preoxidized smelter slag, and the nonferrous tramp oxides were effectively partitioned into the resulting noncrystalline phase. Iron in the ferrous oxidation state was moderately soluble in the glass of reduced specimens but less soluble under oxidizing conditions. The solubility of iron oxide in phosphate glass exceeded the solubility of iron oxide in borate glass. Effective conversion of titanium oxide to rutile was not achieved in the high-iron commercial smelter slag, and 20 to 30 pct of the titanium remained as pseudobrookite, a mixed iron-titanium oxide.

Jan 1, 1973

By Oliver Bowles

"Properties and Uses.Iceland spar is a name given to a pure crystallized form of calcite (CaCo3) which is sufficiently transparent and free of defects to be used in the manufacture of optical instruments. While the actual requirements are small, the degree of purity and physical perfection demanded renders it somewhat difficult to obtain suitable material.The properties of value in Iceland spar are its transparency combined with double refraction. It is used in the manufacture of polarizing microscopes, saccharimeters, colorimeters and photometers. Its most important use is in the manufacture of Nicol prisms, which constitute an essential part of every polarizing microscope. The principle governing the construction of the Nicol prism is as follows:Ordinary light in passing through a crystal of calcite is resolved into two rays of plane polarized light vibrating in planes at right angles to each other and having different indices of refraction. Thus the two rays follow different paths through the crystal. The prism of Iceland spar is cut diagonally and cemented together again with a transparent cement having an index of refraction intermediate between the two rays passing through the prism. Canada balsam is employed for this purpose. The prism is cut at such an angle that the ray having the greatest index of refraction meets the surface of the balsam at an angle greater than the angle of total reflection, and it is thus deflected to the side of the prism, while the second ray passes through. Thus one of the rays is eliminated and polarized light vibrating in a single plane is obtained."

Apr 1, 1920

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By R. R. Sayers

There is probably no industry , trade , or art in which mercury is used but what has produced some cases of mercury poisoning . This is true of the mining and smelting of mercury , where the hazard has long been recognized . When the ore contains free mercury or the more soluble salts , and when the workings are underground and are poorly ventilated , cases occur , but there are a far greater number of cases among the employees about the reduction works . 3 In 1863 William V. Wells visited the mines at Almaden , * Spain , which were worked by convicts . He reported that the men at the furnaces suffered severely , being able to work only about one week out of four , when it was necessary to transfer them to places where the exposure was less . He states that "pale cadaverous faces and leaden eyes are consequences of even these short periods . " Mercury , like lead , when absorbed in small amounts at intervals , as daily, over an extended period of time will result in symptoms of poisoning . This is due to the fact that the mercury is eliminated from the body more slowly than it is absorbed . The frequency and severity of cases of mercury poisoning are far less with modern methods of mining and recovery of the metal than formerly . However , further reduction is possible and much can be done by both the workmen and the operators by following the proper precautionary measures , some of which are described in this chapter .

May 1, 1922

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By Michael G. Zabetakis, Glenn H. Damon, Joseph A. Herickes

The flammability and explosibility of unsymmetrical dimethylhydrazine ( UDMH ) were investigated by the Federal Bureau of Mines to evaluate hazards associated with commercial application of this material as a missile fuel . This program included the following determinations : 1. Temperature limits of flammability in air at one atmosphere pressure ; 2. limits of flammability at selected elevated temperatures and pressures ; 3. 4 . 5. spontaneous ignition temperature in air at one atmosphere and at 200 pressure per square inch gage ( p.s.i.g. ) initial pressure ; spontaneous decomposition temperatures in nitrogen at one atmosphere and at 200 p.s.i.g .; shock sensitivity over a temperature range from about ( ca. ) 25 ° to 50 ° C .; 6. shock sensitivity of reference propellants ( hydrazine , nitromethane , methyl acetylene , etc. ) ; 7 . shock sensitivity of UDMH plus small amounts of selected metal catalysts . Part of the corresponding data was obtained for a mixture of unsymmetrical - dimethylhydrazine and diethylenetriamine ( U - DETA) .

Jul 1, 1960

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By James P. McGee

Preliminary calculations show an economic advantage in using nuclear energy to supply the endothermic heat required for gasifying coal. It should be noted that the various assumptions used in preparing these calculations must undergo further evaluation through additional engineering design and research. The proposed system for gasification is the indirect process cycle with helium heated in a nuclear reactor and passed through an exchanger-type gasifier for the reaction of coal and steam to form CO (carbon monoxide) and H2 (hydrogen gas).

Jan 1, 1960