Search Documents

By Lloyd A. Morley

This report abstracts project work performed under USBM Grant GO155003 during the period 4 November 1975 to 3 November 1976. The research was funded, as a continuance of previous support from USBM Grants GO133077 and G0155003, to gain further knowledge in mine electrical system safety. Five reports have been separately produced, all under the grant title, "Coal Mine Electrical System Evaluation," and are as follows: 1. Volume I - Continuous Monitoring, 2. Volume II - Transient Analysis, 3. Volume III - Shielded Cables, 4. Volume IV - Computer Modeling, and 5. Volume V - Battery and Battery-charging Safety. Abstracts of these comprise the balance of this document with one exception. The task ?d-c offsett currents," does not fall under the scope of the other report volumes and, further, the material to be presented does not justify a separate report. Hence, this subject concludes the Executive Summary.

Jan 1, 1977

By Nabil A. Bibawy

The U.S. Bureau of Mines has established a method for the calibration of class 2 and class 4 standards of mass using a procedure from designs developed by the National Institute of Standards and Technology (NIST). This method produces a weight calibration that is within 1.0 pct of the balance sensitivity. A set of four 1-kg weights yielded a standard deviation of 3.25 mg compared to ±2.91 mg balance sensitivity. The method employs the use of a high-accuracy balance to measure the difference between a set of weights calibrated by NIST and the set to be calibrated. The error of the balance is included in the error for each weight calibrated.

Jan 1, 1989

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Nines investigation of the more economic utilization of the so-called "black oils" of Wyoming,. This problem is being studied by the Bureau of Nines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station, Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oilshas been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), end the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black oil, it was thought t that a more fundamental attack would assist materially in the problem of sulfur removal.]

Jan 1, 1941

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976

By Leon W. Dupuy

Marquette's first reported the existence of iron In Missouri in 1673. Recorded production wan begun in 1815, increasing in size and importance until 1888, when the low price of iron resulting from Minnesota's production of high-grade ore caused most of the operators to close down. Missouri's iron production came from three types of ore: (l) Brown ores, including the deposits of primary and secondary limonites in southeast and southwest Missouri, (2) hematites of the filled sinks, including the ores of Central Ozark district, and (3) specular ores in porphyry, including the deposits of the St. Francois Mountains.

Jan 1, 1949

By William Seymour, L. D. Schmidt

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of the Solid Fuels Administrator for War and with the advice of the Coke Production Committee indicated that production of pig iron could be increased. appreciably if present blast furnaces were supplied with a more uniform coke.4/ Nonvarying percentages of ash , sulfur , and fixed carbon in the coke , together with uniform physical characteristics , such as size , strength , and porosity , would aid the blast -furnace operator greatly in his trial - and - error methods of obtaining maximum production . With nonuniform raw materials he must employ certain factors of safety in operation , such as an excess of coke , an excess of limestone , and operation of the furnace below the maximum rate . Even so , he often has trouble from iron not being up to specifications , hot tops , high blowing pressures , furnace hanging up , etc. The more uniform his raw materials (of which coke is probably the most important) , the nearer to ideally can he run his furnace and thereby save raw material and increase production . One cause of nonuniformity of the coke produced by ordinary American plant practice is the prevailing lack of precise control of the bulk density ' of the coal charge in the byproduct oven . This report summarizes the available information on the subject of bulk density of crushed coal and its control . It includes brief reviews of some of the literature , some results obtained at plants visited by the authors , and results of a few preliminary tests made at the Pittsburgh Station of the Bureau of Mines .

Dec 1, 1943

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence co-efficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculatlon methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By O. Terichow

A pendulum sclerometer designed by the Bureau of Mines is described. Its method of operation is given, along with the results of tests made on representative mineral samples of Mohs' hardness scale to determine the applicability of the device for research on rock testing. The sclerometer hardness values obtained from the tests indicated that reproducibility and accuracy were good. A quantitative comparison of the pendulum hardness values with microhardness and surface energy values published by other investigators showed good agreement on minerals with Mohs' hardness numbers of 2 to 9.

Jan 1, 1967

By J. H. Adkins

The goal of this program was to produce a set of baseline health and safety training materials that could be used by the metal/nonmetal mining industry to reduce injuries and to comply with federal training requirements. The materials developed are arranged in a two level outline format. The first level provides the title, course goals, background and topical outline while the second level provides a detailed outline of the course content. Visuals, designed to portray miners in a positive, attractive fashion, were done in simple line drawing so they would reproduce for handouts without loss of quality. Each of the required units in the Baseline Guides have one or more self-checks. These are designed to be suggestive of evaluation techniques the users can develop for themselves. An instructors guide and a mining terms glossary are included. In a second phase the program developed performance based training guides for Annual Retraining and Experienced New Hires in the Underground Salt Industry.

Jan 1, 1983

By A. R. Rule

Research was done by the Bureau of Mines to determine the effect of a low-molecular-weight polymer on wet grinding of quartz, dolomite, and a copper ore. A 5-in ball mill equipped with a torque sensor for precise measurement of input energy was used for batch grinding tests. Grinding parameters were determined from size distribution data on the feed material and ground product. Zeta potential measurements were made to determine the effect of the polymer on the surface properties of the three materials, and a viscometer was used to measure the effect of the polymer on slurry viscosity. The addition of the polymer caused a sharp increase in the negative value of the zeta potential for all three materials, indicating that pronounced adsorption was taking place. At a constant slurry percent solids, addition of the polymer caused a similar reduction in slurry viscosity for each material. For quartz, dolomite, and the copper ore, grinding efficiency, as measured by kilogram of product per kilowatt hour passing a given screen size, was not affected by the addition of the polymer. However, the lowering in slurry viscosity caused by addi-tion of the polymer permits grinding at a higher slurry percent solids.

Jan 1, 1985

By George J. Carter

Data obtained from field and laboratory examinations were used by the Bureau of Mines to evaluate 82 silica deposits in the Pacific Northwest. A total of 94 field samples was taken from 64 deposits, and an additional 18 deposits were investigated that did not warrant sampling. Of the 37 deposits found to be of high quality, only 16 were large enough to be classified as industrial silica resources. Another 27 deposits did not meet quality requirements. Methods of simple low-cost beneficiation and rapid classification of a large number of samples were investigated in the laboratory. These tests indicated that high-intensity electromagnetic separation was equal or superior to either high-or low-intensity electrostatic separation. In general, the electromagnetic method gave higher recoveries and produced equal or better grade concentrates. A glass button method developed for estimating iron oxide content of silica samples proved to be highly satisfactory as a means of classifying field samples and evaluating beneficiation tests.

Jan 1, 1962

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By Robert C. Steckley

The Bureau of Mines performed a fragmentation experiment in cooperation with Duval Corporation in a porphyry copper-molybdenum deposit near the Sierrita pit south of Tucson, Ariz. This experiment evaluated the fragmentation created in a 10-hole test blast having blasthole spacings of 25, 20, and 15 feet. The 10 blastholes were 9 inches in diameter and contained a total of 17,400 pounds of aluminized slurry blasting agent in 50-foot columns with 60 feet of stemming. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. These core examinations included study of length recovery, rock quality designation (RQD), weight recovery, and size distribution. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the broken material on the surface. Fragmentation to depths of 110 feet was excellent from the 15-to 20-foot blasthole spacing patterns. Good breakage was also produced by the 25-foot pattern although the effects of the blast were not so obvious. In situ leaching tests were not conducted. However, based only on size consideration, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1975

By L. C. Marchont

This Bureau of Mines report tabulates data on nitrogen-gas reservoirs and isolated occurrences of inert gases in several Williston basin oilfields. Recoverable reserves of nitrogen gas in the Minnelusa nitrogen interval within the areas of five oilfields on the Nesson anticline in North Dakota are estimated at about 1.27 trillion standard cubic feet, based on computer analyses of logs from over 300 wells. This volume of nitrogen represents a large source of high-pressure inert gas and warrants consideration of possible application in oil-production operations. Drill-stem tests made in two of the fields indicated that nitrogen can be produced at rates up to 28 million cubic feet per day.

Jan 1, 1966

By Robert E. Barieau

General expressions for evaluating various thermodynamic properties applicable to the van der Waals equation of state have been derived. These formulas were subsequently used to evaluate various thermodynamic functions in the two-phase region. The results indicate that, for a van der Waals fluid, there is a finite discontinuity in the second derivative of the vapor pressure curve, in the second derivative of the chemical potential or Gibbs free energy at the critical point, and in the heat capacity at constant volume measured at the critical density. Numerical values are tabulated and graphs are presented for all functions calculated.

Jan 1, 1967

By E. R. Palowitch, A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high - sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations . The survey , which provided information on Appalachian region coals only , indicated that such important coalbeds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14 - mesh top size . For many other coalbeds amenability to sulfur liberation by crushing was indicated , although too few samples were available to draw firm conclusions .

Jan 1, 1966

By Allan E. Martin, George Glocker, C. E. Wood

"INTRODUCTION As part of a comprehensive investigation of the mechanism of defurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope.Vogt/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FexCay)S and (MnxCaa)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.Coloration of glass by sulfur also provides indirect information on the nature of sulfur in blast-furnace slags./ There seems to be a general agreement at present among the workers in the field of colored glasses that ferrous sulfide is a strong color producer. Colors that have been attributed to this compound include yellow, orange, brown, blue, and black. Apparently the ferrous sulfide is considered to be dissolved in these glasses. There is no indication that any of them have been examined for a colloidal phase.Lorenz 7/ investigated a single manganese slag in the glassy state and observed a Tyndall beam in an ultramicroscope. His conclusion was that either a manganese compound had precipitated in a finely divided condition or that metallic manganese had volatilized and penetrated into the slag as a vapor and thus formed colloidal particles."

Feb 1, 1941

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951