Search Documents

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the utilization of municipal solid waste. One of the primary objectives is the recycling of the magnetic fraction of municipal solid waste (raw refuse). This is consistent with one of the Bureau's goals, which is to minimize the requirements for mineral commodities by maximizing metals recovery from secondary domestic resources, In this investigation, cupola trials were made using combinations of refuse scrap with shredded automobile scrap under basic and acid slag practices. Furnace operating information and the behavior of alloying and tramp elements was obtained. The research showed that it is possible to utilize up to 60 percent refuse scrap in the cupola under basic practice and 30 percent under acid practice, Aluminum in refuse scrap, present in bimetallic cans, increased the recoveries of silicon and manganese charged to the cupola. Increased use of refuse scrap provided iron of lower sulfur. The alumina resulting from oxidation increased the slag volume. The aluminum and tin contents of the iron increased with increasing levels of refuse scrap in the charge. Lead was not a problem with respect to contamination of the iron. In basic practice, operation of the cupola was satisfactory since all slags were adequately fluid. In acid practice, operation became troublesome above the 45-percent level. Under both practices, the cupola iron melting rate decreased. Particulates in scrubber water and stack condensate samples contained lead, zinc, and tin, and the dust load increased. The tensile and transverse strengths of the iron produced under both practices are reported.

Jan 1, 1980

By C. H. Manney

This report deals with the feasibility of the use of vocoders as an integral part of a mine electromagnetic voice communication system. Limitations imposed by the nature of the transmission path, background noise and equipment are examined. Some properties of vocoders and apparent advantages of the use of vocoders in a mine communication are discussed. The conclusion is reached that the man-made noise level will ultimately determine the workability of such a system.

Jan 1, 1972

By Michael Rieber

An analysis of coal slurry pipelines was presented in our May 1976 study, Route Specific Cost Comparisons: Unit Trains, Coal Slurry Pipelines and Extra High Voltage Transmission (4]. The present study extends that analysis. The earlier work included technical and economic cost descriptions of the black Mesa and ETSI pipelines as well as some hypothetical pipeline routes. Water problems, safety and environment, required resources, and labor impacts were discussed at some length. Additionally, pipeline impacts on competing railroads, slurry-rail comparisons, and cost escalation. were analyzed. The difference in pipeline profitability to an owner-operator versus a promoter-builder was suggested. These aspects are not redone in this study. Here, we present a synopsis of the previous results and a general statement of coal slurry pipelines. Extensions of the arguments are presented where they appear warranted. New material is developed in the area of pipeline branching and tapping. This would appear necessary if slurry pipelines are to function as more than private lines; if they are, for example, to be responsive to common carrier requirements.

Jan 1, 1977

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr,5 Fieldner and Davis,6 and others, 7 has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M.8 standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting she results in those types of fuel which give erroneous results due to mechanical losses.

Jan 1, 1932

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By Roy F. Waters

An inventory was made by the Bureau of Mines of wastes of mineral origin, water requirements, treatment of wastes, and water treatment practice of 163 industrial installations in the Lower Missouri River Basin. This is the second and concluding report on the survey, conducted in cooperation with the Missouri Basin Field Committee of the Department of the Interior as part of the Missouri Basin project. Principal industries covered by this second report are: Sand and gravel, coal, meat, ice, brewing, paint, petroleum, chemical, fabricated metals, and a number of industries having either no waterborne wastes, or none of mineral origin. Gravel, sand, and silt from 47 producers are the major wastes, totaling 6 million tons annually, Coal mine wastes in the form of slurried solids from washing crude coal are second in volume, totaling 100,000 tons per year. They contain an average of about 40 percent coal. Salt is the third largest waste, amounting to 28,000 tons per year, Next is calcium carbonate, most of which is formed in water treatments, Because of its high unit value, chromic acid is important, although the waste quantity is much smaller; cyanide wastes are also significant because large quantities of sodium hydroxide and chlorine are consumed in their treatments prior to disposal. The various industries discharging wastes use 38 billion gallons of water annually; the recirculation rate is 109 billion gallons per year. The plants discharging no waterborne mineral wastes use 2 billion gallons of water per year and recirculate more than 1 billion gallons. Sand and gravel plants use 13.5 billion gallons; petroleum refineries use 10 billion gallons in direct use and recirculate 82 billion gallons per year.

Jan 1, 1962

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

By Yoginder P. Chugh

This study has appraised available deeper soil loosening equipment in the 1-4 ft. depth range, in the U.S. and abroad which has potential for Illinois prime farm-land reclamation. The appraisal was based on written and/or oral contacts with equipment manufacturers, reclamation experts, and visiting with selected equipment manufacturers. The results indicate that several manufacturers in the U.S., West Germany, and England market static and vibratory deeper soil loosening equipment which may have potential for application in Illinois. The pertinent information concerning each equipment with potential is presented in this report.

Jan 1, 1983

By W. G. Pariseau

This Bureau of Mines report is an evaluation of the state of knowledge about gravity flow from bin hoppers, the most commonly used method of handling bulk materials where the force of gravity is used. The requirements for flow to be initiated and to continue, formulas developed experimentally or mathematically from various assumptions to describe the materials flow, and the question of whether or not a material will flow over the entire cross sectional area of the bin hopper according to the flow regime developed are the primary areas discussed. The work of A. W. Jenike, whose pioneering investigations raised bin hop- per design from the trial and error state, is examined in depth and its limitations and assumptions are pointed out. Bin hopper design depends heavily upon prior experience, and suggestions for further studies of bin hopper flow to include the effects of feeders are made.

Jan 1, 1972

THE Synthetic Liquid Fuels Act. (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation.3 the Fischer-Tropsch synthesis,4 anal oil shale.5 The Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because coal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form will be valuable. The material will be presented in three parts, as follows: I. United States Patents. II. United Kingdom Patents. III. Other Foreign Patents. The domestic patents for this bulletin were collected between 1953 and 1955.

Jan 1, 1960

By C. R. Summers

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneumatic drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115-dbA stope drill to approximately 100 dbA.

Jan 1, 1974

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By Eugene T. Sheridan

This report presents statistical data on individual plants in the fuel- briquet and packaged-fuel industries circularized by the Bureau of Mines, United States Department of the Interior, in its 1957 annual survey. This survey revealed that 17 briquet and 23 packaged-fuel plants were active part or throughout the year. The annual production capacity of the fuel-briquet industry was 3,088,000 net tons, a decrease of 17 percent from 1956. The decline in capacity was caused in part by the permanent retirement of 4 plants and also by the reduction in capacities of 4 other plants. The rate of production of briquet plants also decreased as the industry operated at 35.8 percent of capacity compared with 40.9 percent in 1956. Every operating plant in 1957 had an annual capacity exceeding 25,000 tons.

Jan 1, 1958

By Jonathan S. Kelly

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and the underground evaluation of ventilated cutting drums, on a double ended ranging drum shearer. The ventilated drum uses high pressure (1,500 psi) water sprays to draw air (3,500 cfm) through 12 airmoving tubes mounted in the drum hub. The sprays draw dusty air from the face side of the drum, scrub the air, and discharge the clean air on the gob side of the drum against a deflector plate. During a three week underground evaluation, the cutting drums reduced shearer generated dust levels at the shearer operators position by 40%, at the shield operators downwind of the shearer by 55%, and at the tailgate by 55%. Cutting and loading performance of the drums were superior to the mine?s conventional drums. After the evaluation, the mine continued to use the ventilated drums to finish mining the panel. During this 3 month period, there were no mechanical or seal failures demonstrating excellent system reliability.

Jan 1, 1987

By Joseph M. Kurtak

The Bureau of Mines (Bureau) and the U.S. Geological Survey (USGS) conducted a 4-year (1979-1982) mineral assessment study of the Chugach National Forest (CNF), Ak, as part of the Roadless Area Review and Evaluation (RARE II) Program. The USGS remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. This report describes the results of Bureau work in the central 790,880 acres of the Forest. Copper, with by-product zinc, silver, and gold, has been the major metal produced from the study area as well as from the entire Chugach National Forest. The majority of the copper deposits are concentrated within basaltic rocks on Knight Island but the major producers are hosted by sedimentary rocks on Latouche Island. Approximately 182.6 million lb of copper, 1.5 million oz of silver, and an unknown but substantial amount of gold were produced during a 30 year period. Currently no mines in the area are producing. Inferred, indicated and measured reserves having mineral development potential total 4.6 million tons, with weighted average grades of 1.6% copper, 0.30 oz silver/ton, and 0.04 oz gold/ton.

Jan 1, 2011

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940

By David E. Nicholson

This report investigates the mechanical behavior of fine soils in a lunar environment in engineering gravity-flow bins. The ultrahigh vacuum, absence of moisture, and a lunar gravity one-sixth that of earth gravity represents a unique environment, both advantageous and detrimental to these systems. On earth, moisture and gases contained in powder masses can be responsible for complex descriptions of gravity flow. Their absence appear to simplify the lunar soil behavior. However, simulation of the lunar gravity and vacuum complicates the development of experimental data for designing bins. The properties of a dry soil powder, its behavior under one-dimensional compression, and its torsional and direct shearing strength under earth atmosphere are described in part 1 of this paper. These properties provide the parameters for a finite-element analysis to optimize the design of bins, to be described by Dr. William Pariseau in part 2. Shear tests assess the failure criteria for the material. Compression tests provide modulus and (Ko) stress-ratio values from the loading portion of the compression cycle, duplicating the condition of a bin at rest with the discharge closed. During the unloading portion of the compression cycle (soil overconsolidated), the residual Ko values rise. It is postulated that this phenomenon creates a high-lateral stress in bins when they approach incipient flow. Assessment of the Ko value, overconsolidation ratio, and the void ratio state is proposed as a criterion to determine the flowability of powder.

Jan 1, 1971

By John B. Umhau

[' is ann.tal surve:' gives sta.tistical data regC:ll~dirg rims.ry and feCOA-dUTY or ~cra:p tin used in thL United States by industries anc. includcc dc..ta l' is ann.tal surve:' gives sta.tistical data regC:ll~dirg rims.ry and feCOA-dUTY or ~cra:p tin used in thL United States by industries anc. includcc dc..ta ]

Jan 1, 1938

Under the Bureau of Mines Research Contract Number H0252071, Foundation Sciences, Inc. has compared the relative effectiveness of roof bolts installed at an angle over the rib with that of bolts installed vertically at the rib side, The information gathered during this investigation was sufficient to supply supplementary information on the mechanics of roof support systems and the general acceptability of field instrumentation methods. During the 140 days of field investigation, 235 bolts were installed, 45 inclined and 190 vertical, in two adjacent intersections. Of these 235 bolts, 30 were in-stalled with load cells and 38 were tested for anchor capabilities. In addition to this instrumentation, the deformation of the opening was measured by convergence meter on 9 lines throughout the two testing areas, and a borescope and photo-elastic gauges were utilized to obtain information on the roof action beyond the surface.

Jan 1, 1977

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969