Search Documents

By C. H. Riggs

This report presents pertinent data on all active water-flooding projects in Washington County, Okla., and describes in detail the operation and production history of five representative floods. The flooding of partly depleted oil-bearing sands to produce petroleum that would not be recovered by other methods is becoming increasingly important to the oil industry. In 1942, two water-flooding projects in Washington County produced 35 barrels of oil daily from 90 developed acres. In March 1951, 4,000 barrels of oil was being produced daily by the injection of 58,000 barrels of water on 19 active projects covering 1,645 acres. Several projects are being extended, and new operations are being initiated. Figure 1 shows the location of the active water-flooding projects in Washington County. The yearly oil production from Washington County increased from 1,076,000 barrels in 1948 to 1,720,000 barrels in 1950, owing principally to the effects of water flooding. To March 1951, permits to flood more than 8,000 acres in Washington County had been granted by the Oklahoma Corporation Commission.

Jan 1, 1951

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

By Thomas Fraser, William L. Crentz

"INTRODUCTION Sulfur is a most damaging impurity in many of our American coals. From the older coal industry of Europe and Britain we can apparently learn but little about the problem of preparing and using high-sulfur coal. Although washing has long been established there for controlling ash content, sulfur is referred to rarely, as the important deposits are singularly low in sulfur.On the other hand, widely distributed coal deposits of America differ tremendously in sulfur content. Many of the more extensive beds contain too much sulfur for metallurgical use, and almost everywhere except in the Rocky Mountain and Pacific coast regions sulfur control is at least a potential problem. American coal-preparation engineers are confronted not only with great variations in the total quantity of sulfur in coal but with an intricately varying pattern of the physical and chemical forms in which the sulfur occurs. It must be conceded that the baffling problem of sulfur reduction in coal is as yet substantially unsolved, for there are but few isolated instances in which we have been able to prepare a satisfactory metallurgical fuel from coals containing as much as 2.0 percent sulfur in the raw state.It has been assumed generally that organic sulfur, being chemically combined with carbonaceous matter, is distributed throughout the coal matter and that it remains unchanged in the clean-coal part of the product during washing.Sulfur that may be washed out of the coal is that part that is combined with the iron in pyrite lenticles associated with the coal. In most of our coals it has been found that, besides the visible bands, lenses, and flakes of pyrite, extremely small and even microscopic particles of pyrite 4/ are distributed through the coal matter. Only the free, relatively coarse pyrite particles .are removed by conventional coal-washing devices, and usually most of the sulfur is still left in the product."

Dec 1, 1947

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By J. M. Mutmansky, L. Xu

"IntroductionSince the establishment of the star,just concentration of 2 mg/m3, a strong effort has made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines.Particular areas of success have been implementation of better coal-cutting strategy to control dust generation, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomski, 1983).While dust concentrations in mining sections have been dropping considerably, one problem area has been mining sections where quartz is a considerable portion of the airborne dust. The federal regulations require that quartz content must be held below 0.1 mg/m3 in the air regardless of the concentration of the total dust. This legislation limits the allowable dust concentration to a ""reduced standard"" of 10/ (% quartz) when the quartz content of respirable dust in the mine atmosphere is more than 5%. Today, approximately one-third of underground coal mining operations have designated areas with more stringent dust standards in place, and many mines experience considerable difficulty in meeting these standards (Jankowski, and Babbitt, 1989).It is well known that metal miners subjected to respirable dusts high in quartz have a higher incidence of silicosis than those exposed to dust low in quartz. However, the role of quartz in the development of coal workers' pneumoconiosis is still a highly controversial question, in spite of the large number of research projects devoted to this subject over the last 20 years. Because coal seams contain less quartz than metal ores and quartz often comes from sources outside the coal seam (e.g., roof and floor), it is difficult to relate studies that deal with the quartz content in coal seams and the incidence of coal workers' pneumoconiosis. Hamilton, Ogden, and Vincent (1983) have provided a plausible explanation for the incidence of the disease by hypothesizing that the quartz content does not affect the probability of developing pneumoconiosis until some threshold value (generally thought to be about 10%) is exceeded.The objective of the research studies summarized here was to obtain a better understanding of quartz occurrences in airborne coal mine dust by studying the variations of the quartz levels in different dust sizes and the relationship between the quartz content in airborne coal mine dust and the quartz content in the mined material. The implications of the results to control of dust in high-quartz sections will also be discussed."

Mar 1, 1992

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By E. D. Gardner

"It has only been in recent years that the proper ventilation of metal mires has received serious consideration. Increasing temperature and humidity with greater depth in some of the larger mines of the West prevented the efficient operation of the mines and made the installation of mechanical ventilation systems necessary. Doors that interfere with tramming are generally needed to control properly the mechanically induced air currents and are one of the inherent disadvantages of the system. In fact the necessity for the use of doors in the main haulageways has discouraged the installation of mechanical ventilation in some metal mines.A number of mining companies in Arizona are using ventilation doors which can be opened and shut mechanically by the motorman without leaving his seat or stopping his train, end thus interfere very little with the transportation of the ore. The Copper Queen Branch of the Phelps-Dodge Corporation at Bisbee introduced these ventilation doors and adapted them from those in use in the company's coal mine at Dawson, New Mexico. Other mining companies have installed the same type of door and it is now being used in a number of districts in Arizona.The doors at the Calumet and Arizona mine in the Bisbee district are representative of those in use. The doors at this mine are substantially built of 2-inch lumber, are air tight, are well placed and have two openings or passageways. The main door, which is used for the motor trains, is 5 feet wide by 6 feet high and is opened by compressed air and closed by a counterweight. At the side of the motor door is the man door, which is 16 inches wide by 5 feet high and is opened and closed by hand."

Aug 1, 1921

By C. A. Komar

Renewed interest in the underground gasification of coal evolves from comprehensive studies of earth fracture systems that indicate that the movement of fluids can be controlled in the coalbed. In particular, directional property studies of natural microfissure occurrence, permeability, ultrasonic velocity, tensile strength, and orientation of intervals of inherent rock weakness, together with geologic structure setting and fracture trace analysis, can predict the gaseous flow paths in the coalbed. Having this information, the dominant direction in which gases generated and/or liberated by heat would move can be determined so that appropriate well patterns can be developed. Together with advances made in drilling technology that permit long horizontal holes to be drilled through the coal seams, tests can be conducted to determine whether directional control will permit devolatilization of the coalbed and gasification of the remaining hot coke in a systematic manner to produce a low-Btu gas suited for the generation of electricity.

Jan 1, 1973

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By M. B. Cooke

 An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study now in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith and Cooke, which involved evaporation of e semple of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the steam bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is ex- cluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

May 1, 1925

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In previous reports 5 results were given of a manhole investigation carried out over a period from June 1929 to July 193C in cooperation with the Edison Electric Illuminating Co. of Boston. Mass., and during 1931 in cooperation with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co., to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by the Edison Electric Illuminating Co. and to develop methods of eliminating these hazards. These investigations have demonstrated that the detection, control, and elimination of combustible hazards in manholes can best be obtained by a close cooperation of the interested parties through a systematic and continuous inspection of manholes, under proper supervision.The investigation carried out during 1932 has been along lines similar to those conducted during 1929, 1930, and 1931 test crew consisting of two men, one an employee of the Consolidated Gas Co. and the other an employee of the Edison Electric Illuminating Co., was continuously employed during the year in the testing of gases in manholes served by the Edison system. The test crew was under the direct supervision of John Campbell, superintendent of the special service department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Consolidated Gas Co.As in the previous investigations, all tests were numbered. The test-data sheets, on which the information regarding the tests was recorded, were prepared in triplicate, ono copy going to the Edison Co., one to the gas company, and the third to the Bureau of Mines at Pittsburgh, Pa. These test-data sheets were then filed (1) according to the town, (2) the street location, and (3) the manhole number; in this way a complete record of each manhole tested was immediately available. A typical test-data sheet was given in the 1931 report. These data sheets were found to entirely satisfactory and no changes were made during the 1932 investigation. The procedure of sampling manhole atmospheres, shipment of the samples to Pittsburgh, and method of analysis has been the same as that described in the 1931 report and need not be repeated here. Likewise, there has been no change in the method of calculation of explosibility of the samples analyzed or the use of charcoal filter tests given in appendix A."

Jun 1, 1933

By William L. Crentz

This Investigation of the preparation characteristics of the coals in Armstrong County, Pa., is the third in a series of Bureau publications by counties appraising the practicability of upgrading marginal deposits to metallurgical standards. Earlier investigations covered the washing characteristics of the coals occurring in Cambria County, and the principal reserves remaining in Indiana County. In Armstrong County, the Upper Freeport bed is the major source of production, the Lower Kittanning bed being of secondary importance. The Lower Freeport bed is mined to some degree, but it is usually too thin and spotty in occurrence to support large-scale operations. The remaining production is taken from the Pittsburgh, Middle Kittanning, and Upper Kittanning beds, but the quantities are insignificant. Table 1 shows the county's coal production) by beds, during 1948. The coals of Armstrong County are not generally considered to be of metallurgical quality because of the high sulfur content. The raw coals usually analyze more than 2 percent sulfur, and more than 4 percent sulfur is not uncommon, especially in the Lower Kittanning bed.

Jan 1, 1951

By Sean Gallagher

Study Design. A split-plot experimental design was used to evaluate the influence of posture, trunk angle, and rotational velocity on peak torque output and myoelectric activity during maximal trunk extension maneuvers. Objectives. To determine whether the kneeling posture alters extension torque capabilities in isometric and isokinetic exercises as compared with standing. Also, to ascertain whether recruitment of trunk muscles is modified by such a postural change. Summary of Background Data. Factors such as workplace geometry may force workers to adopt awkward or unusual postures in the performance of manual tasks. An understanding of the limitations placed on strength in unconventional working postures is crucial to the proper design of jobs. Methods. Twenty-one healthy male subjects (mean age = 36 years 7 SD) performed 12 trunk extension exertions in standing and kneeling postures. Isometric tests were performed at 22.5°. 45°, and 67.5° of trunk flexion. isokinetic tests were done at three velocities: 30°/sec, 60°/sec, and 90°/sec. Electromyographic data were collected from eight trunk muscles to assess muscle recruitment under each condition. A prior; orthogonal contrasts were specified for analysis of both torque and electromyographic data. Results. The kneeling posture was associated with a 15% decrease in peak torque output when contrasted with standing; however, no concomitant change in trunk muscle activity was evident. Trunk hyperflexion (isometric tests) and increasing rotational velocity (isokinetic tests) were associated with reduced torque in both postures. Trunk muscle activity was primarily affected by changes in trunk angle and velocity of contraction. Conclusions. A reduced extensor capability exists in the kneeling posture, despite equivalent trunk muscle activity. The similar activation patterns in both postures suggest that the strength deficit does not result from alterations in trunk muscle function. Rather, it may be the consequence of a reduced capability to rotate the pelvis in the kneeling posture, due to a disruption of the biornechanical linkage of the leg structures. [Key words: electromyography, isokinetic, isometric, low back pain, posture. strength1 Spine 1997;22:1864-1872

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

Provide a means for reliable in situ stress change measurements in soft, friable geologic materials under high stress. Background Effective mine design requires a knowledge of changes in rock stress generated by a mining operation. In situ stress measurement can provide a means of obtaining this knowledge from an active mine for the ultimate purpose of design verification and analysis. The Bureau of Mines has designed and tested a device for measuring changes in rock stress-the borehole platened flatjack (BPF). It has found application in investigating stress anomalies due to geologic structures, stress concentrations from multiple seam interaction, and stress abutments from pillar retreat and longwall mining.

Jan 1, 1990

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By W. W. Adams

The extent to which coal mines have installed various types of haulage systems and mining machines is a subject about which there is little definite information available in convenient form for the country as a whole . A few State mine inspectors include in their annual reports such information for their respective States , but uniform data for the United States have not until recently been compiled . Several years ago the Bureau of Mines compiled from one of the standard mining directories * a statement showing the kinds of machines and haulage used in coal mines . The first statement was prepared from the 1918 edition of the directory in which detailed descriptions of coal mines were given . The information presumably related to the calendar year 1917. Similar statements have been compiled from the directories for 1919 , 1920 , and 1922 , the statement for 1921 having been omitted because the directory for that year did not become available . The latest statement is given below and is based upon the directory for 1922. It relates to conditions prevailing in 1921 , and covers a total of 7,088 coal mines . Of these , 5,064 mines . or more than 71 per cent , were using animal haulage . As compared with the total number of all classes of mines , those in the animal - haul age group constituted 71.4 per cent , the percentage having remained practically stationary during the past four years , although the actual number of mines in the group has increased . Rope haulage was reported by 1,066 mines , or 15 per cent of the total , representing a larger number of mines than in 1918 , but a decrease of 2 in the percentage for the group as compared with all classes of mines . Electric haulage was reported by 3,274 mines (46.2 per cent ) , and the number of motors in use was 11,265 . The percentage of mines in this class has not changed materially, but the actual number of mines has shown a gain of about 900 during the past four years . Compressed-air locomotives have not increased either in actual or relative number , the percentage for the past year being but 1.2 . The number of mines using storage- battery locomotives has increased from 3.6 per cent of the total shown four years ago , to 9.8 per cent for last year, the latest figures showing 693 mines with 1,428

May 1, 1922