Search Documents

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

By J. S. McNabb

"A search for manganese ore by core-drill exploration was carried out by the Bureau of Mines in the Philipsburg mining district in Granite County, Mont., in 1939 and 1940. This work was based on detailed studies of the manganese ore bodies of the district previously made by the Geological Survey.In 1949 further search for manganese in the district was deemed advisable. Diamond drilling was begun the following year as a joint program by the Geological Survey and the Bureau of Mines with the primary purposes of probing ore-leasing structures and extending the limits of known ore bodies. A secondary objective was to test a geologic theory based on a new conception of manganese-ore localization. The exploration targets were designated and the drilling results interpreted by the Geological Survey, and the Bureau of Mines was responsible for the drilling, sampling, and core handling. Improved drilling equipment and methods were utilized in an effort to obtain better core recoveries than resulted from the earlier drilling campaign.The Philipsburg mining district, Granite County, Mont., is 27 miles south of Drurrnnond, about 45 miles airline northwest of Butte, and 1 mile east of Philipsburg. During the course of the investigation patented lode-mining claims owned by the American Machine & Metals, Inc., the Contact Mines, Inc., and the Moorlight Mining Co. were diamond drilled.The district has been an important source of domestic manganese dioxide ore since local recognition of the mineral's importance during World War I. Peak annual output in 1918 of about 127,000 tons of manganese ore was utilized principally by the steel industry. A small but relatively steady output has persisted to the present to satisfy demands by battery manufacturers for battery-grade manganese dioxide.The known manganese deposits of the district are in sedimentary rocks of Paleozoic age. These rocks lie along a north-trending anticline traversed by a series of east-west tension veins. The east flank of the anticline terminates at a steep-dipping fault contact against a small granodiorite batholith.Replacement deposits of manganese oxides and carbonates occur locally in or closely associated with tension veins cutting calcareous rocks, or adjacent to the intrusive. Rhodochrosite has been a common accessory mineral in deposits valuable chiefly for lead, zinc, and silver. Some of the replacement deposits characteristically are irr2gular in outline, whereas others have fairly regular walls marking the limits of favorable beds."

Dec 1, 1955

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion-type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-showing low, erratic methane readings.

Jan 1, 1966

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world&apos;s mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By C. E. Augustine, P. Nicholls

"INTRODUCTION A layer of soot on the heating surface of a boiler decreases efficiency because it increases resistance to the flow of heat, with the result that the heat transfer to the water is lower and the temperature of the flue higher than they would be if the surface remained clean. The percentage of reduction in heat transfer depends on the position and area of the sooted. The percentage of reduction in heat transfer depends on the position and area of the sooted surfaces, the thickness of the most, until the percentage of the total heat absorbed by those surfaces when clean; thus it will vary with the type of boiler and in particular with the ratio of the area of the convection heating surface to the total area. Medium-size and large boilers usually are equipped with soot blowers, and tests have been published giving the increase in efficiency resulting from removal of the soot. Fuel savings up to,8 percent have been reported, but 4 to 5 percent is probably more conservatives. However, these savings may not be due wholly to a reduction the thermal resistance of the surfaces but may be due partly to improvement in the combustion because of better draft or more uniform flow of the gases. In addition, the deposits on the surface of boilers include as a clinker, and as the size of the boiler and the rate of burning increase very little or none will be soot.There are no corresponding test data on small boilers operated at low rates of burning. In stall boilers, deposits are much thicker, and it might be expected that the reduction in efficiency would be greater; in fact, statements have appeared suggesting that the decrease may be as high as 50 percent. This investigation was undertaken because the Bureau frequently receives requests for authoritative information on the effect of soot in small and other heating boilers."

Feb 1, 1935

By J. R. Thoenen

[Since the publication of the preliminary report on this subject in July, 1927, (The Wire Saw in Slate Quarrying, Preliminary Report, Serial No. 2820, by Oliver Bowles) the wire saw has been in constant daily operation at the quarry of the Colonial Slate Company. Luring this time between twenty end thirty successful cuts have been made varying in length from forty-five to ninety-two feet and in depth from six to ten feet. No accurate time records have been kept on these cuts but they have totaled over 12,000 sq. ft. of area and required 19,000 lineal fact During these cuts the average speed of cutting has risen from the 12.8 sq. ft. per hour obtained in the original recorded tests to between 15 and 20 sq. ft. per hour, with the present rate running very close to 20 sq. ft. per hour at this quarry.]

Jan 1, 1928

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

Estimate costs for projected uranium in-situ mining operations. Approach Develop a computer model and an associated data base which will allow users to supply data applicable to a specific mining site in order to estimate total capital and operating costs for a potential in-situ mining operation at the site. How the Model Works The model requires a minimal amount of input from the user. The data input must be known or estimated information about a potential in-situ mining operation. The user can also supply any additional project specifications. The computer model uses a process-engineering approach and determines through a discounted cash flow analysis the total capital and operating costs for the life of the project. This time-span measures from the start of the pilot-scale operation through to the site&apos;s restoration and reclamation. The model will determine the production cost per pound of material mined subject to the rate of return identified by the user. Conversely, it will also solve for the rate of return realized for the specific sales price per pound. [ ] Currently the model&apos;s data base can tai ns costs, rates, and specifications for Texas and Wyoming, the only states where commercial uranium in-situ mining is being conducted. However, this model can be used by anyone who is conducting in-situ leaching or who plans to leach uranium in-situ. At least part of any uranium deposit has a potential for in-situ mining.

Jan 1, 1982

By C. M. McCulloch

The natural vertical fracture system in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north-western West Virginia to N 57° W in southwestern Pennsylvania; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures. Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By Richard J. Mainiero, Michael J. Sapko, James H. Rowland III, Marcia L. Harris

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 @ 10-38 cm6 molecules-2 sec-1 for the rate equation -½d [NO]/dt = K @ [NO]2 @ [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By E. H. Denny

In discussing safety in Colorado metal mines there are two important points for metal -mining men to consider , namely , the direct and indirect cost of accidents and the possibility and means of preventing accidents . For statistics on Colorado metal - mine accidents , reference has been made to published reports of the United States Bureau of Mines on metal- mine accidents from 1919 to 1927. This period was considered because only with the year 1919 are complete figures on nonfatal accidents available and because these years represent postwar activities ; 1927 is the last year for which the U. S. Bureau of Mines has published accident statistics . During the nine -year period 1919 to 1927 , inclusive , 153 metal miners were killed by mine accidents in Colorado and 5,035 miners suffered lost - time injuries . The accidentfrequency rate of number killed per 1,000 300- day workers for this nine - year period was 4.68 as compared with the general average of 3.26 for all the metal mines of the United States for the same period . In other words , the fatality rate in the metal mines of Colorado for this nine- year period averaged 40 per cent higher than that of the metal- mining industry in the United States generally . In 1924 and 1926 the Colorado metal mines had a better accident record than the average of those of the United States , but 1927 was a bad accident year and the State Bureau of Mines figures for 1928 and 1929 showing respectively 18 and 23 men killed in and about the metal mines indicate a continuing relatively high death rate from accident . The cost of accidents to the miner for the period 1919 to 1927 can be estimated from the accident figures just given . The United States Bureau of Mines as well as other authorities assess 6,000 days lost time for every fatality and every permanent total disability . These authorities have also agreed that a permanent partial disability costs 800 days lost time to the worker over his working lifetime , that lost time injuries of less than 14 days average about 6 days lost time and lost time injuries not involving permanent disability but having loss of more than 14 days average 32 days lost time . On this basis the Colorado metal miners have suffered in nine years a gross loss of 1,214,146 days , or , at $5 per day , $6,070,730 . The miner receives about one -ninth of this amount in compensation so that the net loss to the metal miner in Colorado for this nine - year period was about $5,400,000 .

May 1, 1930

By George S. Rice

"Soon after the armistice, an investigation was conducted by the writer on the use of liquid oxygen for explosive purposes in Germany, so far as the conditions of such investigation wore permitted at the time. The results of this inquiry were published in Technical Paper 243, entitled ""Development of Liquid Oxygen Explosives during the War.""Recently, through the courtesy of Dr. C. L. Parsons, former chief chemist of the Bureau, who was visiting Germany, and Mr. Chester L. Benson, of the American Expeditionary Forces in Germany, data was obtained from the Deutsche Oxhydric A. G., Surth near Cologne, (one of the principal manufacturers of liquid oxygen installation) concerning the number of plants which bad been installed in Germany during the period following the armistice. An analysis of the figures obtained shows the following installations in different kinds of mining operations:"

Sep 1, 1920

By G. S. McCaa

Rock-dusting is an. effective means of preventing coal-dust from propagating an explosion in a coal mine, but it will not prevent gas from igniting-explosively and with much attendant damage locally. Ventilation must therefore be effective at all times, regardless of the employment of other explosion-prevention methods, if gas explosions are to be avoided. This paper describes a gas explosion which occurred in as bituminous mine that was well rock-dusted at the point of ignition and which exemplifies the value of rock-dusting, the necessity of maintaining effective ventilation, and the need of permissible rock-dusting machines receiving power from a permissible locomotive. Description of Explosion The mine in which this explosion occurred is developed on a panel system in a practically level seam; the panel entries are driven in pairs, and the air current intakes on the right entry and returns on the left entry. Near the mouth of the intake a door is placed to control the ventilation; board stoppings are placed in crosscuts, except the second from the face, in which a brattice cloth curtain is hung, the last crosscut is left open and line brattices conduct the air current from the last crosscut to the faces. In No. 7 entry the last cross-cut was 152 feet from the face, the line brattice being within 38 feet of this face, and the second crosscut was 250 feet outby the face of the back entry or return. Seven days prior to the explosion the intake and return entries were rock-dusted to within 38 feet of the face, and as the entry had advanced during the week, the rock-dusting was to be extended.

Jan 1, 1929

By Ad. Breyre

[Internal-combustion engines have been used in Belgian mines for a long tine. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted&apos; in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they were replaced later by electric or compressed-air motors. However, the number of gasoline locomotives continued to increase. Regulations governing the use of these locomotives soon were formulated and as early as 1920, when a now set of regulations was promulgated, the use of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have boon incorporated in the regulations.]

Jan 1, 1940

By L. C. IlsLey

"There are two general classes of accidents that prevail in and about mines, namely - (1) those that through the nature of mining work can only be lessened, and (2) those that by proper precaution can be eliminated altogether. Explosive accidents that ordinarily take place while explosives are being transported in and about mines belong to the second class, that is, by proper care all such accidents can in general be avoided.The following table gives a brief summary of several accidents and disasters that have occurred in the United States and indicates the need of universal preventive measures as a basic part of all State regulations.ACCIDENTS AND DISASTERS OCCURRING WHILE TRANSPORTING EXPLOSIVES.***"

Sep 1, 1923