Search Documents

By Albert W. Deurbrouck

Dense-medium cyclone tests in 4-and 8-inch-diameter units have shown the ability of cyclones to make sharp separations down to 100 mesh when washing coals of a finer top size than normally fed to dense-medium cyclones. The reduced top size of the feed apparently allows the finer size particles to report to the proper product by reducing the effect of very coarse particles in the congested separation zone of the dense-medium cyclone.

Jan 1, 1974

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

By R. W. Stahl

Increasing use of continuous miners, especially the boring type, has focused attention on the inadequacy of face ventilation in coal mines. The bulk of the machine, the rapid advance of working faces, and the increased liberation of methane from the larger expanse of freshly exposed coal surfaces have created ventilation problems that were unknown with conventional mining equipment. Ignition of gas, especially that caused by machine bits striking hard rock or pyritic inclusions, have increased at an alarming rate. As the mines penetrate beds under thicker cover at an ever-increasing rate of face advance, this problem will probably increase unless face ventilation is improved. A previous survey, described in Bureau of Mines Report of Investigations 5414, Auxiliary Ventilation of Continuous Miner Places, disclosed that auxiliary fans with tubing generally improved circulation of air and removal of gas at the face. The study here reported attempts to examine, face ventilation at various mines and to note any plan or innovation of. air coursing that industry might adopt to reduce the danger of gas ignition. ACKNOWLEDGMENT The mines visited were very cooperative in the study-and-generously supplied any data requested.

Jan 1, 1960

By Daniel C. Boteler

Data from 68 entrained-bed carbonization tests were treated statistically by the Bureau of Mines, and several useful relationships were developed among the major variables. Nine coals, ranging in rank from lignite A to high-volatile A bituminous, were carbonized in two entrained-bed carbonization pilot plants. The carbonizing reactors employed were vertically mounted cylinders, internally heated, refractory-lined, and 10 inches ID. The range of carbonization temperatures was from 825° to 1,600° F. Using a regression-analysis computer program, empirical equations were developed by which carbonization temperature, air-to-coal ratio, devolatilization of coal, char yield, and volatile matter content of product char may be predicted.

Jan 1, 1973

By C. W. Dwiggins

The Bureau of Mines characterized the chemical and physical properties of metallo-organic materials in petroleum to determine their effect on petroleum production and refining. The structures and physical properties of porphyrins and materials that normally contain metalloporphyrins such as crude oils and asphaltenes were investigated using elemental analysis, NMR analysis, absorption spectrometry, and small-angle X-ray scattering. Petroleum fractions greatly enriched in metalloporphyrins were obtained using asphaltene precipitation, liquid extraction, and large-scale liquid-solid chromatography. Selected fractions containing porphyrins were further purified by chromatographic methods, crystallization, and demetalation followed by chromatography. Nonporphyrin metals could not be appreciably concentrated from the bulk of the asphaltene.

Jan 1, 1969

By F. N. Kissell

The Bureau of Mines has successfully used sulfur hexafluoride (SF6) as a tracer gas to measure mine air flows under conditions where conventional methods have failed. SF6 was employed experimentally to measure accurately recirculation of return into intake air caused by leakage through an old stoped area, to check for potential leakage from an adjacent mine, to trace 10,000 cfm of “lost” air from an intake airway, and to measure transit air time through uranium mines. It proved useful as a means of accurately measuring airflow volumes in airways of large cross section and very low flow velocity, and in determining the recirculation resulting from underground cooling plants.

Jan 1, 1974

To improve the reliability of the Bureau developed bore-hole gage now widely used to determine the absolute state of stress in rock. Approach Use the knowledge gained by extensive field tests to design a more rugged and reliable Instrument using lighter and stronger materials. How It Works The original gage consisted of a stainless steel cylinder 1-3/8 Inches In diameter and 10-1/2 inches long. The new gage is made from titanium. This lighter material reduces the weight of the gage by 43 percent, which enhances the gage placement and depth of overcoring in vertical up? holes. For added strength, the titanium case and placement end are now threaded to the gage body instead of using screw fasteners. Three pairs of strain gaged transducers are positioned to measure the diametral deformation of a 1-1/2 diameter borehole at 60-degree intervals around the Inner surface of the borehole. Each transducer consists of a beryllium copper cantilever with a strain gage cemented on each side. These transducers are secured Into the gage body by a tapered shank for minimal creep. The transducers opposite each other are wired together to form a 4-arm external bridge circuit. A pair of transducers is referred to as a component. Any deformation of the borehole, which occurs during overcoring, is detected by pistons which translate the motion to the components. Each

Jan 1, 1982

By Charles Findlay, Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 cfm. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By Ani Chitaley

A new method has been developed for handling supplies in underground bituminous coal mines. A survey indicates industry wide implementation potential for the proposed method. Reduction of supply handling accidents' by as much as 73% and improvements in the productivity of face operations by at least 3% are anticipated benefits. The new method is based on the palletization of daily supplies and the use of a forklift for carrying out the handling tasks at the underground section. A prototype of the forklift has been delivered to the U.S. Bureau of Mines. The forklift has demonstrated several important features necessary for underground supply handling such as compactness, maneuverability, visibility, ease of control and auxiliary attachments for hoisting, carrying timber and pulling. Design improvements are recommended for future generation underground forklifts. These relate to higher speed, increased battery duty cycle, higher payload and modified traction/steering to eliminate plowing of soft mine floors.

Jan 1, 1983

By Robinson Newcomb

Gypsum is a form of hydrated calcium sulfate (CaS04.2H20) which is widely distributed over the earth's surface. The two varieties worked commercially are rock gypsum and incite. Rock gypsum, the variety commonly mined for commercial purposes, is a relatively soft mineral having a specific gravity of about 2.3 and weighing about 150 pounds per cubic foot. The chief producing States are New York, Michigan, and Iowa. Before being used the crude gypsum is ground and generally calcined. The predominant use of gypsum is for building purposes (the manufacture of plaster), for which calcined gypsum is required. Gypsum is also used as a retarder in Portland cement, as fertilizer, and for other purposes. GYPSUM MINING Crude gypsum is mined by two methods - underground and open-pit. Although the use of the former method predominates, open-pit mining increased in relative importance during the early twenties and contributed about two-fifths of the output during the period 1925-38.

Jan 1, 1940

By Alexander May

In its role to provide technology to prevent or limit adverse environmental impacts associated with mining or minerals processing, the Bureau of Mines has conducted research at its Tuscaloosa Research Center to asess the environmental impacts of phosphogypsum produced by the Florida phosphate industry. Over the years, stockpiles containing 335 million tons of phosphogypsun have accumulated and the industry continues to generate an additional 33 million tons a year. Samples from approximately 1,000 feet of drill core, obtained from nine stockpiles were characterized using chemical, X-ray diffraction, emission spectrographic, radiological, and physical means. The data developed indicated that phosphogypsum is not a corrosive or toxic hazardous waste as defined by Environmental Protection Agency criteria. Radium concentration averaged 21 picocuries per gram and its content was inversely related to particle sizes. Thirty-nine elements were detected in phosphogypsum; concentrations of these elements did not vary with depth within the stockpiles.

Jan 1, 1982

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By Madan M. Singh

This report presents the results of an investigation of inclined roof bolts, anchored over pillars, in room-and-pillar coal mines susceptible to shear failures of the roof. Although the field data do not support this contention, it is believed on the basis of analyses and other work that inclined roof bolts do offer potential under some circumstances.

Jan 1, 1978

By S. McGinn, G. Schnakenberg, D. Petrie, A. Bugarski, M. Grenier

As part of the Diesel Emissions Evaluation Program (DEEP) consortium, Noranda Inc. has undertaken a field project to evaluate the overall performance of the latest diesel particulate filter technology (DPF) at its Brunswick Mine in Bathurst, New Brunswick. Performance of the filtration systems is evaluated with respect to their ability to reduce tailpipe emissions and concentrations of diesel particulate matter (DPM) and noxious gases in mine air, efficiency of filter regeneration process, maintenance requirements, reliability, and acceptance. Four different particulate filter systems deployed on heavy production vehicles are subjected to an 18-month field evaluation. Over the evaluation period the vehicles will have accumulated approximately 4000 operating hours in production. This paper presents the results of testing conducted mid way through the 18-month field trials. The 400- meter section of the mine drift at 525-5 sub level, hereinafter referred to as the "isolated zone" was isolated between intake and exhaust fan systems and sealed with bulkheads against leakage. The isolated zone was ventilated at the rate required per CSA Standards and issued by CANMET for the engines tested. Four vehicles, two load-haul-dumps (LHDs) and two trucks, retrofitted with particulate filter systems were tested along with a new identical model LHD and truck equipped with exhaust systems consisting of a catalytic converter (DOC) and muffler. The test vehicles were operated individually inside the isolated zone for approximately 4 hours over simulated production duty cycles. Measurements of ambient concentrations of particulate matter, tailpipe emissions, and engine parameters were performed for each of the tested vehicles. The DPM samples for carbon were collected at the most up- stream end of the isolated zone, at the vehicle next to the operator, and at the most downstream or exhaust end of the isolated zone. The DPM samples were analyzed for total (organic and elemental) carbon using NIOSH Analytical Method 5040. Ambient concentrations of particulate matter at the exhaust end of the zone were also measured using Scanning Mobility Particle Sizer (SMPS), and real time PAH monitor (PAS 2000). Efficiency of the filters was also evaluated on a basis of tailpipe measurements performed using raw exhaust instruments the NanoMet and the UGAS. In addition, relevant engine parameters were obtained using Detroit Diesel Diagnostic Link (DDDL) and from exhaust backpressure and temperature measurements. Results from the tests proved conclusively that diesel particulate filters can significantly reduce the concentrations of air- borne DPM, but not without careful monitoring of both ambient and tailpipe emissions and not without careful attention with respect to maintaining the integrity of the DPF systems.

By Eric R. Bauer

This Bureau of Mines publication describes and illustrates the physical signs of excessive loading on mine roof supports, installations, and openings. It is designed to assist mine personnel in recognizing potentially hazardous ground conditions, by emphasizing the preliminary effects of developing unstable ground. Increased worker awareness can be expected to reduce the injuries and fatalities resulting from falls of roof, rib, and face.

Jan 1, 1985

By J. G. Groetsch

Municipal solid waste (MSW) contains about 8 pct ferrous metallics which are typically recovered by magnetic separators at municipal resource recovery facilities. At present, only about 182,500 ton/yr of MSW magnetics are being processed for remelting out of the -11 MMton/yr discarded. The Sn in MSW magnetics makes this material difficult to recycle to the steel industry. An electrolytic method using stannous fluoborate-fluoboric acid for removing Sn was evaluated. Optimum concentrations of Sn in the electrolyte and the effects of impurities such as Al, Cu, Fe, and Pb on Sn recovery from the electrolyte were evaluated. Operating parameters were 60 to 65 g/L fluoboric acid and 20 to 30 g/L Sn using stainless steel electrodes at a current density of 60 A/ft2. Tests were run with postconsumer scrap4 and MSW magnetics. Good results were obtained with MSW magnetics, after pretreatment by reshredding, magnetic separation, and air classification. The final Sn content of the MSW magnetics scrap was reduced from 0.18 to 0.017 wt pct. Heat and solvent treatments of MSW magnetics to remove coatings did not significantly improve Sn removal beyond that obtained with material that had only been mechanically pretreated.

Jan 1, 1984

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX's Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

Improve transmission of data from an underground mine monitoring system to a remote, mass-data storage system. Background Instrumentation systems in underground mines must operate under environmental extremes of dust and humidity, local electromagnetic/radio frequency (EM/RF) interference fields, and potentially explosive atmospheres. During a recent roof-bolt study performed by the Bureau of Mines, it was necessary to transmit a large quantity of data to a data storage system. Conventional wire cable transmission presented several limitations which often required special electrical isolation or physical protection. Because conventional wire cable presented certain problems, the Bureau of Mines investigated alternative means of data transmission. The research investigation led to the selection of fiber optic cable for data transmission applications. The fiber optic method of data transmission offers several advantages: ? Since the transmission medium consists of light waves, it is safe to use in gassy mines. Where applicable, MSHA permissibility standards for peripheral devices must be met. ? It is lightweight and rugged. ? It can operate up to 131000 feet (4km) without repeaters and without EM/RF field interference.

Jan 1, 1986

By B. I. Ferber

Toxic and explosive atmospheres are discussed, along with some of the instruments commercially available for their detection. No attempt has been made to evaluate the accuracy of anyone device. This circular has been prepared primarily to aid mine inspectors in selecting suitable instruments for underground gas detection.

Jan 1, 1972

By Raymond M. Stateham

Climatic conditions are compared with roof fall occurrence from April 1, 1972, to December 31, 1975, by the Bureau of Mines. These comparisons indicate that humidity has a strong influence on roof fall occurrence rates. Cubic regression techniques are used to develop best fit curves. Statistical analysis of these curves indicate that both are sinusoidal and exhibit positive correlation with each other. The sine waves have a period of 1 year with maximum and minimum inflection points in August and February.

Jan 1, 1978