Search Documents

By Michael M. Hamilton

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 37,542-acre portion of the 57,002-acre Riordan?s Well Wilderness Study Area (NV-040-166) in order to evaluate its mineral resources. The area studied is located in Nye County, NV, about 60 miles southwest of Ely, NV. Subeconomic mineral resources of limestone and sand and gravel were identified in the study area. The Troy and Irwin mining districts, 4 miles to the west, were active between 1868 and 1963, producing small amounts of gold, silver, lead, and tungsten from mines well outside the study area. Except for minor prospecting activity, most mining activity in the study area has been since 1980, consisting of claim locations and geochemical surveys.

Jan 1, 1987

By Melvin E. Poad

This Bureau of Mines report presents two phases of a research program to evaluate a single-entry system for longwall development. Organizations participating in the program; which began in July 1971, include the Bureau of Mines, the Mining Enforcement and Safety Administration, and the University of Utah, working under a cooperative agreement with Kaiser Steel Corp. at its Sunnyside mine in Utah. Part 1 of this report describes the present longwall mining practice, including a brief history, and discusses the advantages and disadvantages of a single-entry development system and its introduction in the United States. Part 2 of the report presents the research program; test design, instrumentation for ground and support evaluation, and the test results from the No. 2 mine. Subsequent reports will describe the research conducted in the No. 1 mine.

Jan 1, 1977

The object of this program was to design and build a self-contained system for remote monitoring of the atmosphere in mines. The system developed uses the mine pager phone line as the primary communication channel and also has the capability of using 208 Hz in the ELF band for wireless transmission through the earth. The depth for through-the-earth transmission is expected to be about 80 to 90 meters in high conductivity soil and is limited by the noise level in the ELF band-pass filters. The underground components of the TEM System are energized by mine power through a battery charger - storage battery power supply. In the event of mine power failure the battery capacity is more than sufficient for one week's operation with interrogations every four hours.

Jan 1, 1980

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

By A. D. Garman

The mining ordinance of Costa Rica dates from 1830. In spite of the numerous attempts to enact a new ordinance , it has been so much amended and reamended during the hundred years of its existence either expressly or , more often , by implication , and sometimes by Executive Decrees of which the validity has been called in question - that in most cases no one but a lawyer thoroughly conversant with Costa Rican mining practice could properly advise with reference to it . The present attempt at a digest of these laws is based on the 1929 edition of Bolandi and Johanning - the only source available in Washington . Apparently this edition has no official character , and the editors themselves often made surmises although one would think that definite facts would be available in Costa Rica where it was published .

Jul 1, 1930

By L. C. IlsLey

[In 1922 a conference of representative coal-mine operators, cable manufacturers, mining-machine manufacturers, and representatives of the United States Bur eau of Mines vas held at the Pittsburgh Experiment Station, regarding suitable cables for use with permissible raining machines. This conference recommended that the Bureau investigate rubber-sheathed trailing cables in order to obtain specifications for tests leading to approval for rise with mining machines. Effective until such time as an investigation could be made, the bureau asked the several manufacturers of approved mining machines to recommend cables for wise with their machines. In general the Cables recommended tentatively approved. Arrangements for the tests were completed in 1927. Concentric-type cables were investigated first, and Reports of Investigations, Serial No. 2909, covering the tests, was issued in January, 1929.]

Jan 1, 1929

By Eric E. Cather

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 5,100 acre (2,065 ha) Rubicon RARE II area (No. 5026) in the El Dorado National Forest (fig. 1). Work by the Bureau of Mines indicates that potential for mineral resources in the area is low. Samples from small gravel deposits along the Rubicon River and from favorable structures in the area contained smart amounts of economic minerals. A Tertiary river channel near the north area boundary contains gold values as much as $137.60 per cu yd ($180 per cu m) [(gold at $400 per troy oz ($12.86 per g)]. The channel does not cross the study area. Energy resource potential, including oil, gas, or geothermal, does not exist in this geologic environment.

Jan 1, 1982

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

By N. H. Snyder

Coal analyses help to describe the character of coal as it lies in the ground of as it may he delivered to the user Analyses of samples of coal collected from the face of the bed in mines are plentiful, but available analyses of delivered coal are relatively few, and there is a distinct difference between "mine samples" and "delivered samples.” Mine samples are collected actor drag to a standard method. 13 The sampler cuts a channel. 2 by 6 or 3 by 4 inches from roof to, floor in the face of the bed, and excludes from the sample all partings more than 3/8 inch thick, and any lenses or concretions of sulphur or other impurities more than 2 inches in maximum diameter and 2 inch thick. Analyses of mine samples form a permanent and scientific record of the coal bed at the point sampled, they ale important in determining the character of the coal in any given mine or district These analyses, when the samples are taken by a standard method, are valuable to the operator When compared with analyses of delivered coal they show him whether his mine is being worked efficiently or whether the coal is being properly prepared, which involves the ques¬tion ii Nether he has suitable mechanical appliances for separating the impurities sties. In the purchase of coal, mine samples may serve as a sufficient guide for the experienced buyer who has knowledge of the impurities in the bed, and the degree to which these are eliminated in mining and preparing the coal To the average purchaser, however, unacquainted with these details, dependence on mine samples may be misleading The quality of coal indicated by the base samples call rarely, if ever, be attained in the delivered coal Certain impurities that are eliminated from the formally prepared mine sample may not be eliminated by the miner Some of the roof and floor may also be included if these are soft or flaky When coal prices are high and competition is lessened it is easy for the miner and the management to lower the standards of preparation, and a return to rigid stand¬ards is always difficult. In sampling delivered coal the Bureau of Mines follows a definite procedure. 14 A sample of not leas than 1000 pounds is systematically

Jan 1, 1928

Objective A cable bolt can be a strain-measuring device as well as a supporting device in underground mines. Placing instruments on a cable bolt allows certain characteristics of a rock mass, such as high strain and load, to he evaluated during mining and provides a means for mining engineers and mine inspectors to forecast a potential roof fall. Background Thousands of cable bolts are installed in U.S. mines each year. Studies performed by NIOSH researchers show that support loads can exceed the yield point of the steel, which can result in unstable ground conditions that pose direct safety hazards for underground workers. Rock falls can also create secondary hazards, such as caved escape ways and blocked ventilation passages. Development of methods and tools to assist in the evaluation and selection of rock supports could reduce the number of unplanned rock falls significantly. Approach Instrumented cable bolts developed at NIOSH’s Spokane Research Laboratory were used along with existing ground control systems to monitor rock mass loads and movement Axial and shear loads on the cables are determined as these loads are transferred to strain gages embedded in the king wire. In longwall, room-and-pillar, or underhand cut-and-fill mines, rock mass loads and movements can be detected down to microstrains of stress or millimeters of movement. By detecting such small amounts of ground movement and support load, early intervention to prevent a roof fall is possible, and miner safety and health are increased. How it Works Up to 10 strain gages are embedded in the king wire at whatever locations a mine ground control engineer may specify. The gages m either be set in pairs in the same plane to detect shear or set at 90° angles to detect loading in three dimensions. The cables are up to 5 meters long if they arc to be grouted with resin or up to 15 meters: if they will be grouted with cement. They arc capable of holding m ultimate lend of 214 kN and produce reliable readings to 178 kN, as shown in the calibration curve. The cables are fitted with an instrument plug for monitoring the gages and a special head for insertion into the rock. A data acquisition system, such as a Vishay strain indicator box, Campbell Scientific, or Omnidata system, is required to obtain the data for load and displacement calculations.

Nov 1, 1998

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines' horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau's methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

By R. A. Kearns

To enable the mining industry to be kept informed as to the availability of equipment developed by mining equipment manufacturers in their constant endeavor to keep a step ahead of changes in mining techniques, the Bureau of Mines periodically issues lists of equipment approved subsequent to the last previous listing. The present list covers those approvals issued during calendar years 1953 and 1954. It supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953. The procedure established in Bulletin 543 of numbering items in each category consecutively to indicate the chronological order of the approvals has been continued in this circular. Information on approvals issued later than January 1, 1955 may be obtained by referring to Coal Age, a monthly magazine issued by the McGraw-Hill Publishing Co.

Jan 1, 1955

By D. G. RUNNER

Information Circular 6148R, " Selected Bibliography of Minerals and Their Identification ," was issued in June 1929 , revised in July 1937, and again in October 1938. The popularity of this circular , combined with the desire to make it more comprehensive , has occasioned the preparation of this compilation of references . Where possible , date of publication , publisher, current price , and number of pages are given, although prices are subject to change at intervals . The references are grouped under the following headings : minerals , gems , rocks , geology, geomorphology, engineering geology , prospecting, mining . engineering, microscopy, technical dictionaries , and miscellaneous . For ready reference, the authors ' names are arranged alphabetically under each grouping . This list is not comprehensive, but contains only those references in most common use and which are generally available in public college libraries .

Sep 1, 1949

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981

By Ivan F. Avery

PRODUCTION of carbon black decreased 4 percent in 1961. Output in the major producing States of Texas and Louisiana decreased 1 percent and 8 percent, respectively. Production of channel black continued downward, declining 10 percent in 1961 compared with 9 percent in 1960. Furnace black production also decreased 3 percent from 1960. Total domestic sales, however, increased 2 percent, Sales to most major consumers increased, but sales to the ink industry decreased 10 percent. Producer's stocks decreased 5,083,000 pounds during the year. Exports decreased 4 percent. SCOPE OF REPORT Carbon black is a very pure grade of quasi-graphitic carbon; particle diameters range from 50 to 5,000 angstrom units. Annual reports were submitted to the Bureau of Mines by operators of all commercial plants in the United States.

Jan 1, 1962

By Harold W. Lipper

HELIUM shipments in 1963 exceeded the volume shipped during the previous year for the 14th successive time. Shipments from Bureau of Mines plants were 627.3 million cubic feet, an increase of 5 percent over the volume shipped in 1962. Production from Bureau of Mines plants totaled 774.2 million cubic feet. The Bureau purchased 1,420 million cubic feet of helium in the helium conservation program and stored it underground for future use. Each of the five plants, financed and built by private industry for helium conservation, made deliveries during the year. Helium continued to playa key role in space, atomic energy, defense, and other research programs. Additional capacity for liquefying helium became available, and the first civilian helium-cooled nuclear-powered reactor in the United States began pre-operation testing.

Jan 1, 1964

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

The object of this program was to design and build a self-contained system for remote monitoring of the atmosphere in mines. The system developed uses the mine pager phone line as the primary communication channel and also has the capability of using 208 Hz in the ELF band for wireless transmission through the earth. The depth for through-the-earth trans- mission is expected to be about 80 to 90 meters in high conductivity soil and is limited by the noise level in the ELF band-pass filters. The underground components of the TEM System are energized by mine power through a battery charger - storage battery power supply. In the event of mine power failure the battery capacity is more than sufficient for one week's operation with interrogations every four hours.