Search Documents

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By Richard L. Rains

In 1992, the Bureau of Mines evaluated mineral resources of the 34,043-hectare Caribou City and 41,943-hectare Stump Creek study areas in southeastern Idaho. No resources were delineated. The areas had been proposed for wilderness. Rocks underlying the study area are part of the Idaho-Wyoming Thrust Belt. At Caribou Mountain they have been intruded by diorite-monzodiorite. Where the intrusive rocks contact calcareous members of the thrust belt, skarn bodies have formed that host metal deposits. Gold, both placer and lode, occurs in the Caribou City area, and salt occurs in the Stump Creek area. Production records show 73.5 kg (2,363 ounces) of placer gold were produced; however, field studies indicate more than 2,000 kg (67,000 ounces) probably were recovered. Minor amounts of lode gold, silver, and copper were recovered from the hard rock mines. Production of salt from the Stump Creek study area in the 1860's was used by emigrants on the Oregon trail and also shipped to various mining districts for use in silver recovery. Oil and gas were drilled for, but all holes are plugged and abandoned. There are no current leases. Examined workings consisted of 25 adits, 3 shafts, 50 prospect pits, and extensive placer workings all in the northern tip of the Caribou City area, Current BLM records show 168 placer and 146 lode claims; 14 claims are patented.

Jan 1, 1993

By D. Harrington

Every few weeks United States newspapers of 25 or 30 years age ran scare-heads telling of some mine disaster, which was a first-page attraction for a day or two and then was forgotton until another disaster occurred a few weeks later. Interspersed with these disasters were the so-called sniping mine accidents, causing the death of one or two mine workers. The summation of all types of mine fatalities usually exceeded 3,000 a year. In the period 1906-10, inclusive, there wore 84 major explosion disasters (or about 17 per year) in united States coal mines; the fatalities resulting from those disasters numbered 2,388 for the 5-year period. These frightful catastrophies helped to cause the total number of fatalities in our coal mines for the 5 years (including the fatalities from major explosions) to reach the enormous total of 13,288, an average of 2,658 per year. In addition, some hundreds of other typos of mining accidents swelled the annual fatality list to upwards of 3,000. This admittedly deplorable condition created so much Nation-wide comment that Congress was impressed with the necessity of having something done by the Federal Government with a view to trying to halt at least sonic of the excessive loss of life in our mines; in consequence, the Bureau of Mines was created and began to function in July 1910.

Jan 1, 1935

By R. R. May

A preliminary examination of the Houston strip-coal mine, situated on the Alaska Railroad at milepost 175 (61 rail miles north of Anchorage, Alaska) and a review of all available information resulting from early coal exploration activities in the area resulted in plans to investigate the coal-bearing formations at depth by means of diamond core drilling to indicate the existence of additional reserves of coal in close proximity to railroad transportation, where it would be quickly available to meet rapidly expanding military and civilian fuel requirements. From the date of mobilization of equipment, August 28, 1951, until date of suspension, August 18, 1952, 2,010 feet of diamond drilling was completed. Ten definable coal beds were cut, of which 2 appear to be persistent and minable over an area of approximately 1/2 square mile. Within this area the 2 minable beds contain approximately 5,000,000 tons of coal in place. Of the remaining beds, at least two others may be minable to the eastward near their projected outcrops; however, these and deeper beds (at least in the vicinity of the drill holes) lie beneath a zone of pressurized gas and brackish water. From a practical standpoint, continued development and utilization of the coal in this vicinity will depend on the operators' ingenuity in developing cheap mining methods and on diligent prospecting for strippable coal under the comparatively light glacial cover.

Jan 1, 1957

By E. C. Lane

This paper is a preliminary report of the results of the Bureau of Mines' twenty-second semiannual survey of motor gasoline marketed in the United States. A more detailed discussion of the whole survey is in preparation and will be published as a companion, report. The second paper, in addition to giving a more complete summary of the data included in this report, will present results of the determination of copper-strip core lion (method 530.22), color (method 10.11), sulphur content (method 520.11) evaporation residue (method 530.1), and gum content as given by the Bureau of Mines steam oven method.9 The retail price at the time the sample was taken and tax will also be stated for each sample. The present paper deals specifically with data relating to gravity, vapor pressure, and distillation. It has been the feeling of some investigators that the practice, followed in previous semiannual surveys, of grouping all types of motor fuel together without discriminating between "competitive price gasoline," benzol blends, Ethyl gasoline, "high-test" fuels, etc., has detracted from their usefulness because the data did not permit drawing conclusions in regard to any one type of fuel, and tended to obscure differences between fuels of the various types. Therefore, in order to remedy this condition, the samples of the present survey have been divided into two groups; one called "competitive-price gasoline" and a second group called "premium-price motor fuels."

Jan 1, 1930

By J. W. Thompson

MINERALS OWNERSHIP AND POSSESSION. The owner of minerals under a conveyance from the surface owner does not lose his right or his possession by mere nonusage of the minerals. McBeth v. Wetnight (Indiana), 106 Northeastern, 407, p. 410, October, 1914. QUIETING TITLE TO MINERALS-PLEADING. A complaint in an action to quiet title to minerals and to the min- eral rights in certain land is insufficient in the absence of a direct allegation of possession, although it avers that the plaintiff from the time of receiving the conveyance assessed the mineral interest for taxes each year and paid the taxes thereon and exercised various acts of ownership of such mineral interests, in that he caused test pits to be dug on the land for the purpose of exploring the minerals and ascertaining their quality and extent, in going upon the land and looking after them from time to time, and that he accompanied or caused his agents to accompany prospective purchasers of such mineral interests and exhibited the same to such prospective pur- chasers in efforts to sell them. Fowler r. Alabama Iron & Steel Co. (Alabama), 66 Southern, 672, p. 673, Novem- ber, 1914. SALE BY MARRIED WOMAN-VALIDITY. A conveyance by a married woman of the mineral rights in certain described land is void where she had previously conveyed the land to another grantee who had acquired title by adverse possession under the deed.

Jan 1, 1915

By R. Havens, B. K. Shilber

"INTRODUCTION In the course of the investigation of the occurrence of manganese deposits in the western United States, ore-dressing tests were made on three samples procured by Bureau of Mines engineers from two properties in southeastern Juah County, Utah, each of which is known by the name Black Jack. To avoid confusion, the tests will be described under the names of the owners Kendall-Duvall and the Empire Mines.None of the samples were amenable to ore dressing for the production of high-grade manganese sinter.Ores from the Kendall-Duvall deposit represent an interesting metallurgical phase of low-grade manganese occurrence, as the occurrence of manganese as silicate (braunite) automatically governs the extent to which they can be beneficiated by mechanical methods of treatment. As less than 50 percent of the total manganese was recoverable by complex methods of treatment in a 40- percent-manganese sinter, attempts were made to recover most of the manganese in a low-calcite, intermediate-grade product that might be acceptable for subsequent metallurgical treatment. By selective flotation of calcite and manganese, up to 68 percent recoveries were obtained in plus 20-percent manganese products..No encouragement can be given for successful ore-dressing of Empire ores as represented by samples received for testing, as no products were obtained that would meet minimum marketing specifications. Empire ore contained only 1 percent lime and might be high enough in grade (19 percent manganese) for direct hydrometallurgical treatment."

Nov 1, 1947

By Robert D. O'Brien

"INTRODUCTION The Miscellaneous Minerals Division of the War Production Board requested the Bureau of Mines to investigate the Gallatin corundum property as a possible source of corundum, which was in short supply due to the war. The Gallatin corundum property, also known as the ""Fuller mine"", the ""Montana Corundum mine"", and as the ""Old Qorundum mine"" was first examined by a Bureau of Mines engineer 2/ in July 1943. Bureau of Mines work on the property started October 11, 1943, was recessed May 5, 1944, and was resumed in October 1944 when the diamond-drilling program started. The project was completed February 7, 1945. The data obtained are given in this report.The Federal Geological Survey made a reconnaissance survey in the spring of 1943 and mapped the area the following autumn. The results of these surveys are contained in a memorandum report prepared in December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By Clyde E. Williams

[As a results of work conducted during the past three years, the Northwest Experiment Station of the Bureau of Mines, in cooperation with the University of Washington at Seattle, Washington, has developed a process for the production of sponge iron. Commercial operation of this process in a 3 to 4-ton scale has been so satisfactory that its use on a large scale (20 to 100 tons per day) can be safely considered. Description of Process. The process consists in passing a mixture of iron ore and coal through a rotating kiln heated at one end to a temperature sufficient to convert iron oxide to metallic iron, discharging, cooling, and separating the sponge iron from the residual coke and silicious material on a magnetic separator. Both the coal and the ore should be crushed to peso as 6-meth scream, tans producing particles finer then 1/12 of an inch. Seventy-five parts of coal or other carbonaceous material arc charged with every 100 parts of ore), This large amount of coal is required in order to supply sufficient carbon to maintain a strongly reducing atmosphere in the charge, but may be reduced to about 65 parts per 100 parts of ore by recovering and using tae carbon that remains in the discharge product. Large-scale operation and refinements in furnace design should lower this ratio to perhaps 56 or 60 parts of coal to 100 parts of ore.]

Jan 1, 1924

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 3 Program Description The computer program developed to simulate events in the case of fire in the mine is described in this section The description is divided into three parts. 1. Program Capabilities This part summarizes what inputs can be changed, what outputs can be obtained and demonstrates program flexibility through suggested uses.

Jan 1, 1976

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976

By F. A. Penning

A number of highly instrumented free fall tests were performed on an arrestment system for a man cage in a vertical shaft. Tests were conducted in the U.S. Bureau of Mines free fall test tower at the Colorado School of Mines. A single tooth safety dog was used to stop on 4x6-in. Keruing (Phillipine mahogany) wet and dry wood guides. The safety dog had a penetration depth of 1 in., an adjustable width from 1-1/2 to 2-1/4 in., and a tooth angle of 80 deg. Twenty-seven free fall tests were performed covering a range in weights from 3-1/2 to 10-1/2 tons, hoisting velocities from 850 to 1350 feet per minute. Average g loads were measured from a low of 0.6 to a high of 3.4. The electronic instrumentation included piezoelectric and seismic mass accelerometers, strain gages on structural and mechanical elements, load cells in the guides, and distance measuring. Computer analysis was used to correlate with experimental measurements used to calculate stress. A statistical analysis gave no indication that the velocity or area affected the wood crushing stress. The instrumentation revealed a chatter occurring during the stop as shown by the accelerometers, strain gages, and load cells. Additional work is required to analyze this newly discovered phenomenon. The chatter imposes loads much higher than the average g load.

Jan 1, 1980

By R. J. Fantel

To determine the availability of phosphate rock from domestic re- sources, the Bureau of Mines evaluated the potential production of phosphate rock from the demonstrated resources of 130 mines and deposits. The evaluation included an estimation of resources, engineering methods, and capital and operating costs, and an economic analysis to determine each operation's average total cost of production over the life of the mine, including a 15-pct discounted-cash-flow rate of return on all investments. Quantified but not evaluated in this report are substantial phosphate resources at the inferred and hypothetical resource levels. The 130 mines and deposits contain 6.4 billion tons of recoverable phosphate rock product, about 20 pct from producing mines. At total production costs of under $30 per ton in January 1981 dollars, about 1.3 billion tons of phosphate rock product is potentially available, over 90 pct from producing mines. This study suggests that production from low- cost, high-grade phosphate mines now in operation will decline during the next decade, and new higher cost, Lower grade mines will have to be developed to satisfy demand into the next century, In addition to the demonstrated resources evaluated in this study, 7 billion tons of inferred-level and 24 billion tans of hypothetical- level phosphate rock are potentially recoverable, which, in part, includes material containing high amounts of magnesium, Much of this material could likely become available in the near future.

Jan 1, 1983

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels'. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m (26.5 ft) above the miner's head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roof beam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

By Gregory P. Cole, Peter G. Kovalchika, Rudy J. Matetic, Adam K. Smith

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/nonmetal miners had a hearing impairment by age 501. Mine workers are exposed to additional noise levels underground due to the reflection of machine generated noise that would otherwise dissipate in an above ground setting. Determining the sound absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed, rather than reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of some of the materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes: a finite room, a diffuse field, and relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper will present a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients will be essential for determining and predicting potential overexposure to machine operators in different mine environments.

By Van H. Manning

PETROLEUM INVESTIGATIONS. The work of the petroleum division of the Bureau of Mines during the period of the war was under the supervision of Chester Naramore, chief petroleum technologist. In its petroleum investigations the bureau cooperated freely with other Government bureaus and acted as a source of information on petroleum matters. COOPERATIVE WORK ON INTERALLIED PETROLEUM COMMISSION. On July 15, 1918, Mr. Naramore and W. E. Perdew, chemical en- gineer of the bureau, left for London to act as representatives of the United States Fuel Administration and the United States Shipping Board on the Inter-allied Petroleum Commission. Numerous con- ferences were held with representatives from France, England, and Italy on specifications and requirements of the various allied Govern- ments for petroleum products, and for this purpose meetings were held in London, Paris, and Rome. EXAMINATION OF PETROLEUM FACILITIES IN FRANCE. The storage facilities and the transportation system in France were studied, and recommendations based on the information gained were made to the director of the oil division of the Fuel Administra- tion and to the chairman of the Shipping Board. Refinery plants in France were inspected, as well as filling stations and shipping facilities from ports in France and Italy to the various fronts and the petroleum base of the American Expeditionary Force at Romorantin. France. At the request of Ambassador Sharp, a re- port was prepared on the advisability of developing the petroleum resources in France.

Jun 1, 1919

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining, on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years

By Lloyd A. Morley, Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in/which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-roof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges. Explosion-proof enclosure techniques have been utilized in U.S.

Jan 1, 1974

By P. Kovalchik, S. Peng, G. Cole, R. Matetic

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90 percent of coal miners and 49 percent of metal/nonmetal miners had a hearing impairment by age 50 (Franks, 1997). Mine workers are exposed to additional noise levels underground due to the reflection of machine-generated noise that would otherwise dissipate in an aboveground setting. Determining the sound-absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed rather than being reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes a finite room, a diffuse field and a relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper presents a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients are essential for determining and predicting potential overexposure to machine operators in different mine environments.1