Search Documents

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

Provide respiratory protection for escape in a toxic or oxygen-deficient atmosphere with a device small and light enough to be belt-worn. Approach Combine a 10-minute, belt-worn respirator with a stored, larger, long-duration (60-minute) attachment that can be plugged into the 10-minute unit without removing the mouthpiece. How It Works The 10-minute device will be carried by the miner at all times, and the 60-minute canister or attachment will be stored near the miner. In the event of a disaster, the 10-minute device would be donned immediately. The miner would then proceed to the stored 60-minute unit and plug it into the 10-minute unit. For the 10-minute unit, a breathing circuit was developed in which air is passed through the KO2 bed twice per respiration. The 60-minute canister differs from the 10-minute unit in that air is drawn only once through the chemical bed per respira-

Jan 1, 1981

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan's toxicity,

Jan 1, 1982

By Kenneth B. Higbie

PRESIDENT LYNDON B. JOHNSON announced at midyear that the test flight of the A-It plane, the world's first super-sonic aircraft capable of flying 2,000 miles per hour, was made possible by "the mastery of the metallurgy 'and fabrication of titanium." Not all of the contributions made by the mineral industry in 1964 were acknowledged so widely. Yet the contributions were significant as the search continued for new and improved methods for providing metals and mineral products to meet the ever-expanding requirements of the world economy. This chapter reviews only a few of the metallurgical developments that resulted from U.S. and foreign research efforts. MINERAL BENEFICIATION Up-to-date theory 'and practice in the mineral ,Processing field in 1963 involved subjects such as autogenous grinding, high-intensity magnetic separation, and mill control by computers. These subjects were fully discussed at the Seventh International Minerals Processing Congress held in New York City during September.

Jan 1, 1965

By Jürgen F. Brune, William H. Schiffbauer

Communication problems are not new. Research in this area goes back as far as 7922 when the US Bureau of Mines performed experiments to detect radio signals from inside their experimental mine in Bruceton, Pennsylvania. Many improvements to mine communications have been made over the years but for any number of reasons the underground coal mining industry has been behind in implementing advances. Present communications systems far underground mines can be hard-wired or wireless. Both types of systems can fail when faced with fires, roof falls, explosions, and power or battery failure. Currently installed wireless communications systems usually employ a special antenna cable called a "leaky feeder" Fiber optic cables are also used in some applications to form a "backbone" for wireless transceivers. Through-the-earth (TTE) and wireless radio systems are less common. Except for TTE systems, most wireless systems require some wire-bound components, which are susceptible to failure during disasters as cable breakage interrupts communications.

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

By M. C. Irani, Maurice Deul, M. G. Zabetakis, T. G. Bobick

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By W. E. Webb, R. H. Church, W. G. Hopkins

The development of systems for location of miners who have become entrapped following a mine disaster has been one of the major research goals in the Bureau of Mines. This study details the preliminary development of such a system. Current technologies for locating trapped miners from the surface are either simple direction, finders or time difference pulse systems that have accuracy Limitations. Developing technologies using full vector field measurements at several receiving points are currently being studied. The necessity of measuring field strength with great accuracy can be a drawback in these systems. A system that operates with continuous wave radio signals, whose phase differences can be measured accurately even in weak signal conditions, greatly improves the location accuracy. A microcomputer would be used, in conjunction with the system, to gather and manipulate the data to automatically pinpoint the location of the trapped miner. Comparison of this system with existing technology indicates a favorable accuracy/complexity ratio for the phase difference of arrival technique.

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude oils from producing fields in the United States and has published a series of reports on different fields, including oil fields of Texas3. Production Data The Spindletop field was discovered in 1901 when the pay sand was found at deaths of about 800 feet. During the following twenty-five years a number of attempts were made to find a deep productive sand. All attempts sere failures until a roll drilled by the Yount Lee Oil Company found oil late in 1925. An intensive drilling campaign began at once, and the production of the Spindletop field increased to a daily average of 93,217 barrels in September, 1926; the present production is estimated at 66,000 barrels doily. Tile following table taken from the Oil and Gas Journal for February 10, 1927, shows the daily average and the total production by ninths for 1926.

Jan 1, 1927

By Vernon R. Miller

The Bureau of Mines developed and evaluated a detector-sorting device to separate the copper-bearing portion from the barren portion of native copper ores. Small-scale sorting tests were run on minus 1-inch plus 1/2-inch size materials from the following Michigan samples: Winona, Kingston, and Centennial ores, and "poor" rock from the Champion mine dump. Results showed that 60 to 85 pct of the copper was recovered in 9 to 19 wt-pct of the sorted fraction. About 90 pct of the copper recovered was obtained in the first pass through the sorter. For the Kingston and Centennial ores, combinations of sorter concentrates and fines generated during crushing, resulted in recoveries of 93 and 94 pct, respectively, of the total copper in the samples. The combined products constituted about 66 wt-pct of the total sample and allowed the balance to be discarded with only a 6 to 7 pct copper loss.

Jan 1, 1974

By Linda L. Chasko, Charles P. Lazzara, Ronald S. Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

By Richard L. Rains

The Bureau of Mines conducted a mineral investigation of the 29,000-acre Dixie Summit area near Elk City, Idaho, during the summer of 1989. At the Petsite mine a marginally economic, identified resource of 4.9 million tons with an average grade of 0.023 ounces gold per ton was delineated. Possible resources of gold, along with silver, copper, lead, and zinc, occur in at least eight other lode deposits. Placer gold may be recoverable by recreational-sized suction dredges in some stream drainages, Five lode mines in the study area have produced over 5,516 ounces of gold (placer gold production was not recorded), 4,757 troy ounces of sliver, 36,746 pounds of lead, and 3,800 pounds of copper. Current mining claims in or adjacent to the study area total 460 lode and 70 placer claims. There are two patented lode claims within the Dixie Summit study area.

Jan 1, 1991

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other volumes of the international studies of the Minerals Yearbook, it is clearly impossible to cite all sources of information used in its presentation, but some recognition seems due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of our counterpart agencies throughout the world. Information they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, we must begin by expressing our appreciation to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1993

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Ergonomics processes described in the literature have been associated mostly with manufacturing, financial, electronics, and office settings where working conditions tend to be rather constant and repetitive. The information presented in this document demonstrates, however, that an ergonomics process can also be implemented in a setting such as mining where working conditions frequently change and workers are periodically exposed to extreme weather conditions. This document describes how Bridger Coal Company implemented an ergonomics process at its Jim Bridger Mine from 2001 through 2004. The process developed by the Ergonomics Committee, the promotion of the process to management and employees, and the impacts of the process on working conditions at the mine are reviewed. Barriers overcome and lessons learned are also described. Quotes from Bridger Coal Company employees are included in the document to add a personal perspective. Other industries with working conditions similar to mining, such as construction and agriculture, may find this information useful.

Jan 9, 2006

By L. Nahai

COAL, salt, lapis lazuli, and construction materials such as lime, gypsum, slate and stone were the only mineral commodities produced in Afghanistan during 1963. Beryl has been produced sporadically. Small deposits of chromite and lead-zinc are known but remained unexploited because there were no domestic markets for the two commodities and transportation costs from Afghanistan to world markets were too high. Oil fields of sufficient magnitude to justify exploitation have not been discovered, but known natural gas reserves are substantial and have potential significance. There is evidence of large high-grade iron ore resources, but these are in an unfavorable location. The contribution of the mineral industry to the economy was small, although precise figures are not available. The reported value of mineral production in 1963 (excluding barite) was 181.6 million afghanis (about US$4 million). Employment in the industry, including cement plants and quarries, was estimated to be no more than about 2,000.

Jan 1, 1964

By Gary R. Gavan

This report presents the documentation and User's Manual for a data retrieval and report generation computer program. The program operates on a data base containing over 19,000 pieces of coal mine equipment in use in 1976.

Jan 1, 1979

By Carl F. Wingquist

Electrical resistance heating to effect thermal fragmentation of semiconductive rock was examined by the Bureau of Mines. Tests were carried out on copper-bearing ores of the Nonesuch Shale Formation in the laboratory and in the the field at White Pine, Mich. Fieldwork included primary and secondary breakage tests. Heating tests on in situ rock failed to produce thermal dam-age to an extent considered useful; however, boulders up to 30 ft3 were effectively broken by the method. Power input to the test rock was taken from a 50-kV, 5-amp dc power supply.

Jan 1, 1976

By J. M. Singer

Quenching distances for flames of methane-coal dust mixtures were determined with air and oxygen-enriched air. Coals used were Pittsburgh, Sewell, and Pocahontas No.3. Quenching distances were greater for flames of hybrid mixtures of coal dust and methane than for methane flames of corresponding stoichiometry. From the data of quenching distances and methane-coal dust concentrations was calculated the quenching equivalence, which is the increase in coal dust concentration required to maintain a given quenching distance value as the methane concentration decreases. These equivalences could be useful in identifying hazardous methane-coal dust mixtures in mines.

Jan 1, 1966