Search Documents

By Jeffrey M. Listak

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

Continuously monitor and record respirable dust levels underground by a reliable, sensitive, and fast-response device. Approach A light-scattering photometer, having a LED (Light Emitting Diode) light source and other significant improvements, has been designed and incorporated into a portable continuous monitor. How It Works The monitor continuously draws air into the sampling inlet through a cyclone that removes dust particles larger than respirable size. The dusty air enters the photometer vertically downward through a cylinder which is intersected by the optical system. (This cylinder appears as a circle in the drawing of the photometer.) The center of he column of dusty air intersects a beam of pulsing light from the LED, causing some of the light to be reflected, scattered, and refracted. Only the light that is scattered at an angle of about 700 from the light beam passes through a lens to the photodetector which generates an output voltage Signal proportional to the dust content in the air. This signal is detected, amplified, and converted to a digital readout directly in milligrams of dust per

Jan 1, 1979

This report describes the redesign, development and field demonstration of a remote shotcrete lining system, capable of operating in shafts and mines from 8 to 16 feet in diameter at depths up to 1000 feet. The original contractural scope of work outlining problems and remedial measures associated with a previous unit proved inadequate. Significant additional effort was necessary in order to fulfill the project objectives of producing a functionally reliable remote shotcrete lining system. Included with the engineering and technical description of the system, is a comprehensive technology package. Included with this material is ancillary equipment, materials selection procedures, mix-design data, quality control and assurance program, selection and training of personnel and the organizational aspects required to operate the entire system. The report concludes with details of a successfully completed borehole lining operation at the Nevada Test Site. An irregular 104 inch diameter borehole was lined at a rate of 4.8 feet per hour and 20 feet per hour respectively for 8-9 inch and a 2 to 3 inch shotcrete thickness.

Jan 1, 1983

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

6. Development of Mine Sealant Material Systems 6. 1 Introduction The preliminary evaluation of material systems described in Section 3 led to the selection of the following four promising systems for further development: System A: Aggregate, Fly Ash System System B: Aggregate, Fly Ash, Urethane Foam System System C: Aggregate, Bulkhead, Light Expansive Concrete System D: Aggregate, Self-Supporting Thick Slurry Preliminary laboratory tests indicated that the building of effective bulkheads from one borehole would be extremely difficult. Two extra boreholes would be required adding to the overall cost of the system and making the system less attractive. Tests with light expansive concrete showed that bulkheads would be required, the material would not support itself. As a result, further development of this system was terminated. Foam concrete was selected as the most suitable material to be developed into a self-supporting, rapid-setting slurry. A laboratory investigation of its use for mine sealing was conducted during this program; the results are summarized in Section 6. 5 and details of the laboratory program are presented in Appendix B.

Jan 1, 1973

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

China?s New Steel Complex Postponed. - The planned $5 billion Baoshan Steel Works near Shanghai is being laid aside for 6 months to a year, and may be abandoned altogether. The second phase of construction, in which Wean United, Inc., of Pittsburgh was a major participant, has definitely been cancelled. Over $1 billion had been committed to the 6 million-ton-per-year plant. U.S. Firm Develops South African Fluorspar. - The Armco Bronne Co. of Middletown, Ohio, plans to spend $27 million to develop a fluorspar mine in the Republic of South Africa, With fluorspar reserves at 20 million metric tons, the project is planned to produce 200,000 tons Per year of fluorspar for export starting in 1983. U.S.S.R. Resumes Sales of Titanium Sponge. - Against a background of increased U.S. titanium sponge supplies, the Soviet Union is offering limited quantities of this commodity to the U.S. market at approximately $10.00 per pound, down from $25.00 per pound last year.

Jan 1, 1981

By Larry G. Stolarczyk

This report deals with information regarding a new Medium Frequency (MF) Wireless Communication System for underground mines. This new telecommunication system works on low loss electromagnetic wave propagation modes which allow it to provide quality radio communications almost anywhere in a mine. Tests show the MF system can provide improved safety and managerial control, increased productivity, better organizational team-work and reduced maintenance cost; furthermore, MF's unique design allows for easy installation at a minimum cost. This paper covers the following: 1) MF design plan, 2) Overview of mine radio communications systems, 3) Preparations needed for designing an MF system, 4) MF equipment, 5) MF installation, 6) MF design considerations, 7) MF design specifica¬tions, and 8) Recommendations dealing with MF system. Experiments in four mines are illustrated to demonstrate the success and via¬bility of the MF system. The mines range from small (500 tons/day) to large (67,000 tons/day) capacity and represent several different mining methods. The MF Wireless Communication System represents an advancement in mining communication and the groundwork for other advanced mine systems.

Jan 9, 1984

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By Sidney Katell

Continuing the series of cost bibliographies which was initiated with the publication of Information Circular 7516 in October 1949, the present report covers the period from January 1959 through December 1959. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, were obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil. On Oct. 16, 1959 a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers became effective. This agreement provides for the publication of the annual bibliography under the sponsorship of both groups with the work load involved in the preparation divided equally between the two. As a result, the present report partially reflects the efforts of the members of the Association.

Jan 1, 1960

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

Identity the difficulties of establishing vegetation on mining-related wastes resulting from adverse chemical, physical, and biological properties; describe the ecological and soil factors affecting the relationship between mycorrhizal fungi (soil microorganisms) and plants; and evaluate the feasibility of establishing vegetation on mine waste by introducing mycorrhizae. Problems in Revegetation Successfully using vegetation to stabilize a situ disturbed by mining-related activities depends on knowing the chemical, physical, and biological characteristics of the site prior to, or at the time of, stabilization. The primary objectives of mine land reclamation are to minimize environmental degradation and to facilitate the re-establishment of a functional plant-soil system. Mining disturbances can significantly alter the physical, chem¬ical, and biological characteristic of a site, thus affecting plant establishment, survival, and growth. The physical disturbance caused by the removal and replacement of soil and overburden, together with the waste material from ore processing, affect the chemical, physical, and biological process within the disturbed soil or waste. Additionally, variability in soil properties results from differences in climate, topography, vegetation, and parent material of the site.

Jan 1, 1993

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972

By Lisa Steiner, Robin Burgess-Limerick

In 2004, there were 646 underground coal mines in the USA employing 37,445 miners. These mines reported 3556 injuries to MSHA that year - 17% were associated with bolting machines (593 injuries), 8% with continuous miners (283 injuries), and 4% each with Scoop/LHD (1 51 injuries), shuttle cars (134 injuries), and personnel transport (145 injuries). The use of the frequency of reported injuries for the prioritization of risk control strategies has limitations because of the tendency to underestimate the importance of relatively rare but high-consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggest the following hazards as the highest priority for elimination or control: • rock falling from supported roof • inadvertent or incorrect operation of bolting controls • handling continuous miner cable • collisions while driving LHD/Scoop, shuttle cars and personnel transport • rough road while driving or traveling in LHD/Scoop, SC & PT

By Frank E. Federspiel

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 47,000-acre Electric Peak study area (part of the formerly-designated RARE II Non-wilderness Recommended Area no. 1609) to evaluate its' identified mineral resources. The study area is in Powell and Jefferson Counties, YT, about 30 mi southwest of Helena and 30 mi north of Butte. Three lode localities within the study area contain an estimated 159,000 tons of identified subeconomic resources containing gold, silver, and accessory lead, copper, and zinc. Resources at those localities range from 10,000 to 134,000 tons with grades ranging from 0.04 to 0.32 oz/ton gold, 0.92 to 16.42 oz/ton silver, 0.14 to 79.65 percent lead, and as much as 0.41 percent copper and 0.68 percent zinc. One property also contains 0.15 percent antimony. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that further exploration may identify resources on seven additional study area localities.

Jan 1, 1988

By H. N. Smith

IN 1944 the Congress passed the Synthetic Liquid Fuels Act that authorized the Secretary of the Interior, acting through the Federal Bureau of Mines, to conduct basic research and construct and operate demonstration plants to produce synthetic liquid fuels from coal, oil shale, and other substances. As a basis for the oil shale investigations to be undertaken in this country, the progress of foreign countries in developing and using oil shale as a source of liquid fuels was studied by the technical missions of the Federal Bureau of Mines. Oil shale mines, retorting plants, and refineries were visited; geological information on the nature and occurrence of the foreign oil shales was obtained; and samples of the oil shales were collected where possible. Samples collected by these missions or acquired by other means came from Australia, Brazil, Canada, France, Manchuria (China) , New Zealand, Scot-land, Spain, Sweden, Thailand, and Union of South Africa. These countries represent a large part of the locations where oil shale developments have taken place. The major omissions are the Estonian, German, and Russian developments.

Jan 1, 1959

By Lloyd A. Morley

This report details the continuation of mine power systems transient research under USBM Grant G0155003. The purpose of the work, which commenced under Grant G0133077, is the elimination of safety hazards created by transients" and the objective is to provide knowledge about transients existing in a-c and d-c coal mine power systems. The report chapters cover theoretical background, instrumentation, and experimental investigations. The instrumentation discussion scans measurement problems and considerations plus the development of a low-cast peak-detector. Transient data from in-mine measurements are presented and include high-voltage distribution and d-c trolley systems. Extremely unique field exercises are described involving actual power equipment connected on the surface to duplicate typical underground coal mine system arrangements. Here, transients on high-voltage distribution resulting from vacuum circuit breaker operations could be observed under controlled conditions, and work centered around how surge capacitors effect transients. Using the in-mine and staged transient data, specific conclusions and recommendations are made with emphasis on high-voltage distribution.

Jan 1, 1977

By Steven J. Page, John A. Organiscak

Prolonged exposure to airborne respirable coal mine dust is responsible for coal workers' pneumoconi¬osis (CWP): Furthermore, miners who show evidence of higher radiographic categories of simple CWP are at increased risk of developing progressive massive fibro¬sis (PMF). As of 1990, there were nearly 130,000 coal miners in the United States. "' This excludes mines that produce less than 10,000 tons annually and the anthracite coal mines. Estimates indicate that at age 58, an average of 7/1000 U.S. workers and 89/1000 U.K workers will have developed PMF(2-1) Health research studies have iden¬tified that the risk of developing and the severity of CWP arc directly related to (1) the amount of respirable dust exposure and (2) the coal rank.,'- The rank of coal is its stage of formation in the series peat, lignite, sub-bituminous, bituminous, and anthra¬cite (in order of increasing rank). The rank of coal can also be represented by the com¬mercially important characteristics specified by its proximate analysis: fixed carbon, vol¬atile matter, mineral matter, and moisture content.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX C - HOISTING SYSTEMS - AVAILABLE EQUIPMENT C 1 - Introduction A survey has been made of available hoisting equipment which has applications for use in metal and non-metal mine emergency escape hoist systems. The information was gathered from a number of sources, including representatives in the USBM and MESA, mine operators, personal visits and telephone interviews with manufacturers, field visits to inspect equipment, advertisements, catalogues and indices of manufacturers. Wherever possible, technical specifications and prices were checked out with the manufacturer, or supplier. The sections on individual sub-systems and components, such as automatic control systems, winches and controls, are not intended to be all encompassing surveys. Rather a reasonable number of representative units in each category are discussed. The sample is large enough to provide a general picture of the kind of equipment available, including the abilities and limitations and a reasonable price range. The survey has been divided into six categories 1. Complete Hoisting Systems A Above ground installations B Below ground installations 2. Hoist Assemblies ^(Man-rated) 3. Hoists (not Man-rated)

Jan 1, 1976