Search Documents

By Edward L. McHugh, Charles Sabine, Jami Dwyer, David G. Long

Slope failure accidents were responsible for about 12% of U.S. surface mine fatalities between 1995 and 2003. Small surface movements on a mine highwall may be precursors of failure that, if detected, could provide sufficient warning to enable workers and machinery to be withdrawn to safety. Radar interferometry offers the necessary precision to detect these movements. Radar has some advantages over other methods in its ability to cover large surface areas for true two-dimensional monitoring day and night under almost any weather condition. Radar’s active transmit/receive mode of operation provides for more direct sampling than do passive optical methods that depend on solar illumination. Improvements in microprocessor speeds and capacities have led to the development of a number of small, portable, ground-based systems; such systems are now being deployed at several locations around the world. As part of an ongoing study of monitoring technologies, researchers from the National Institute for Occupational Safety and Health and Brigham Young University, Provo, UT, cooperated to assess the feasibility of using interferometric radar to monitor mine slope stability. Field tests of a device incorporating prototype equipment were successful in that small, centimeter-scale displacements on rock slopes were detected.

Jan 4, 2006

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By Harold M. Smith

This report presents a complete qualitative picture of knowledge of the composition of petroleum as of April 1965. The material is presented in detai 1 on two imaginative maps--one, the Hydrocarbon Hemisphere, depicts the hydrocarbons that have been identified in petroleum; the other, the Heterogeneous Hemisphere, shows the sulfur, nitrogen, and oxygen compounds that have been found. All compounds are placed on the maps according to boiling point. The accompanying text illustrates by structural formulas the several types of hydrocarbon and nonhydrocarbon compounds identified, presents some quantitative data, and points out the possible geochemical significance of a number of the compounds. The possibilities of the Petroleum World of the future are discussed as a function of needed research.

May 1, 1965

By William D. Mayercheck

The U.S. Bureau of Mines is conducting research aimed at providing technology for a low-cost, high-recovery, environmentally acceptable mining system to recover the vast thin-seam coal reserves existing in the mountainous areas of the Appalachian region in the Eastern United States. As part of this research, the Bureau is evaluating new techniques to address these coal resources. This report summarizes the results of a worldwide technical search on thin-seam coal mining, the formulation of various methodologies for mining mountaintop thin seams, and the implementation and status of a physical model test program to validate and further develop the most promising concept-the "roof-fall-tolerant" mining system.

Jan 1, 1990

By Harold M. Smith

This report presents a complete qualitative picture of knowledge of the composition of petroleum as of April 1965. The material is presented in detail on two imaginative maps--one, the Hydrocarbon Hemisphere, depicts the hydrocarbons that have been identified in petroleum; the other, the Heterogeneous Hemisphere, shows the sulfur, nitrogen, and oxygen compounds that have been found. All compounds are placed on the maps according to boiling point. The accompanying text illustrates by structural formulas the several types of hydrocarbon and nonhydrocarbon compounds identified, presents some quantitative data, and points out the possible geochemical significance of a number of the compounds. The possibilities of the Petroleum World of the future are discussed as a function of needed research,

Jan 1, 1966

By Harold M. Smith

This report presents a complete qualitative picture of knowledge of the composition of petroleum as of April 1965. The material is presented in detail on two imaginative maps--one, the Hydrocarbon Hemisphere, depicts the hydrocarbons that have been identified in petroleum; the other, the Heterogeneous Hemisphere, shows the sulfur, nitrogen, and oxygen compounds that have been found. All compounds are placed on the maps according to boiling point. The accompanying text illustrates by structural formulas the several types of hydrocarbon and nonhydrocarbon compounds identified, presents some quantitative data, and points out the possible geochemical significance of a number of the compounds. The possibilities of the Petroleum World of the future are discussed as a function of needed research,

Jan 1, 1966

By Byron S. Kutscher

This report summarizes the program to develop and construct an improved light-scattering dust monitor (ILSDM). This improved light-scattering dust monitor, which operates on the forward light scattering principle, provides instantaneous measurements of airborne dust concentrations in units of mg/m. The program was divided into two phases. Phase I involved the design of the ILSDM which was reviewed by the Bureau of Mines. Phase II included the fabrication of a prototype ILSDM based upon the design developed during Phase I. After completion, the ILSDM was delivered and demonstrated at the Bureau of Mines. A description of the final ILSDM design, operating instructions, maintenance instructions and recommendations for additional work are also included in this report.

Jan 1, 1980

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By A. Livingston

This paper on mining practice at the Fresnillo silver mines is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Two classes of ore are produced at Fresnillo. A low-grade oxidized silver ore; end a complex-base sulphide are containing gold, silver, lead, zinc, and copper. This paper is confined to a discussion of operations relating to the production of oxidized silver ores. To date, more than 10 Million tons of this ore rave been mined. The present (June, 1931) daily production is 2,000 tons of ore, and approximately 600 men are employed in the mining operations.

Jan 1, 1932

By Robert M. Cox

The objective of this study was to determine if significant relationships exist between coal mine roof stability and the time roof is left unsupported. Additional factors such as geology, opening geometry, and mining methods were also studied: to determine their relative influence on mine roof stability. The results of the study indicate that geologic factors such as shear zones (either joints or faults) and changes in roof rock lithology were the principal factors governing mine roof stability. The time lapse factor appeared to be of critical importance when poor mine roof conditions are encountered. The study pointed up the need for improved and permissible rock mechanics instrumentation for use in coal mine investigations.

Jan 1, 1974

By T. C. Shelton

The Bureau of Mines Contract No. H0101706 with Virginia Polytechnic Institute and State University was a part of a broad-scale investigation directed toward applied problems in mine safety and particularly toward preventing accidents and fatalities resulting from falls of roof and ribs in coal mines. Under the auspices of the Chemical Stabilization Program, Bureau of Mines, Spokane Mining Research Center, Spokane, Washington, the broad objective of the Contract was to conduct research for the purpose of studying the behavior of large engineering structures. Contract No. H0101706 consisted of two related but distinct tasks. TASK I was to make "Barodynamic Analysis of Large Mine Models," and TASK II was "Preparation of Undisturbed Rock Specimens.?

Jan 1, 1974

By Chas. F. Jackson

The work of the mining division is divided between seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal minim section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following pages the objectives and type of work of each section will be summarized briefly and the active problems listed. The work done during the calendar year 1936 will also be summarized.

Jan 1, 1937

By B. D. Hanson

An interactive computer program has been developed by the Bureau of Mines which enables the user to identify the effect of cutting system changes on relative dust generation for longwall shearer drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. The user can change one or more of these parameters at a time to determine their effect on relative dust generation, cutting forces, and/or cost. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs. This program is a more comprehensive version of the relative dustiness index (REDI) program described in Bureau Report of Investigations 8979.

Jan 1, 1988

By George R. Ingham

This paper is one of a buries being prepared by the Bureau of Mines on mining methods and costs at various mines in the United States, and is a description of the mining practice at Ajo, Ariz., where the New Cornelia Branch of the Phelps Dodge Corporation mines copper ore from an open pit, and operates a concentrator for the treatment of the ore thus mined. ACKNOWLEDGMENTS The authors wish to express their appreciation to M. Curley, manager of the New Cornelia Branch of the Phelps Dodge Corporation, for his review of this paper and permission to publish it. They also wish to acknowledge the assistance given by W. C. Lawson, assistant engineer, in the preparation of the paper.

Jan 1, 1932

By R. L. Soderberg

Large open stopes mined by vertical crater retreat or sublevel s are sometimes backfilled with uncemented sand to support the stope walls and alleviate rock bursts. The failure of bulkheads in two different mines prompted a research project at the Bureau of Mines to prevent a recurrence of these failures. A series of laboratory tests with drains and sand filters was conducted to measure the bulk-head pressures when adequate drainage was maintained. Results showed that bulkhead pressure was reduced to near zero while drains were in operation, as compared to full hydrostatic pressure when drains were blocked or drainage was restricted. A relatively simple, free-draining bulkhead was shown to be adequate.

Jan 1, 1985

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By Marvin S. Seppanen

Computer programers are often required to make modifications to unfamiliar Fortran routines. This Bureau of Mines report describes a computer program designed to aid the programer in such a situation by reorganizing: Fortran routines. This reorganization includes a sequential renumbering of the routine's statement numbers, a sequential renumbering, and relocation of format statements, an alphanumeric reordering of dimensioned and typed variables, a uniform pattern of text spacing, and a sequential numbering of the records in the final Fortran routine. The computer program has been extensively tested by the author and has proved to be a valuable tool for reorganizing Fortran routines developed under contract and later utilized by the Bureau, and for preparing routines for publication.

Jan 1, 1975

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985