Search Documents

By A. E. Wells

A critical study of the wet Thiogen process for extracting sulphur from the smoke of smelters is one of several investigations related to the general smelter-smoke problem that are being conducted under the direction of the Bureau of Mines. Part of the work done in the pyrometallurgical section of the cooperative metallurgical exhibit of the Bureau of Mines at the Panama-Pacific International Exposition during 1915 related to this investigation, and at the expiration of the exposition, the work was continued in the labora- tories of the Bureau of Mines in the Hearst Memorial Mining Building of the University of California, Berkeley, Cal., where a mining experiment station of the bureau has been established under the cooperative agreement with the University of California. Early in the spring of 1915, when plans were being made to co- operate with several metallurgical interests, the Thiogen Co. proposed to the Bureau of Mines that, along with the studies of various pro- posed methods for eliminating sulphur dioxide from smelter smoke, there should be included a study of the wet Thiogen process. In the study as outlined it was proposed to determine whether it would be technically and commercially feasible to use the, process for the recovery of elemental sulphur from the sulphur dioxide in waste smelter gases. Although there had been no large-scale work with the process, either in the laboratory or at a smelter, representatives of the metallur- gical and mining industry had shown considerable interest in the proposed method, and the desire had been expressed that a better knowledge of the possibilities of the process should be obtained. Thus, cooperation with the Thiogen Co. seemed justified by the in- terests of the metallurgical industry, and by the conservation promised by the recovery of a product of market value from what is otherwise a waste, and in some instances a serious nuisance. In accepting the responsibility for directing this investigation, the officials of the Bureau of Mines were necessarily free to conduct the work in the manner they considered necessary to determine the facts. It was also understood that any information obtained was to be made available to all who might be interested and might be printed in a Bureau of Mines report. To cover the cost of laboratory equipment and supplies, and the payment of salaries of assistants, other than Bureau of Mines employees, the Thiogen Co. in May, 1915, deposited with the cooperative metallurgical exhibit fund a sum considered sufficient to warrant starting the laboratory investi- gation. The origin and organization of this fund has been described by Clevenger and the author." In outlining the program for this investigation it was hoped that ultimately a small complete plant would be erected and the investi- gation center around the operation of the plant. However, pre- liminary to the erection of the plant, a laboratory study of the proc- ess was considered necessary, as the technical features of the process could be determined, it was believed, as satisfactorily on a smaller scale as on the scale first proposed. However, it was realized at the time that it would not be possible to determine so satisfactorily or definitely the commercial possibilities of the process on the scale of work adopted as in the larger operating plant. With this fact in mind it was planned that, if the study of the technical features on a laboratory scale gave sufficient promise of the process being commer- cially feasible, an operating unit should, if possible, be constructed later, and that more definite information concerning the commercial prospects should be determined. The investigations were started in June, 1915. In June and July work was confined entirely to small-scale laboratory tests, in which a careful study of the chemical reactions involved was made. In August, tests on a larger scale were started, and these were con- tinued until December, small-scale tests being made at the same time. On December 1, 1915, all work on the Thiogen process was discon- tinued temporarily, as the close of the exposition necessitated moving the laboratories. Work on the Thiogen process was started again in January, 1916, in the laboratories of the new mining experiment sta- tion at Berkeley, Cal., and was continued during the spring of 1916 until a point was reached where it was felt that the essential parts of the process had been carefully covered, and that some definite state- ments concerning the technical features and possibilities of the process, as given in this report, were warranted.

Jan 1, 1917

By Thomas J. Fisher, Christopher C. Jobes, Edward F. Fries

This report (Software Safety 2.2) is the third in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended or use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and non networked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety .• 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the Safety File is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be don and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treaty of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 9, 2001

By Joseph H. White

In its investigations looking to the improvement of health condi- tions and the increase of efficiency in the mining industry, the Bureau of Mines, in cooperation with the Bureau of Public Health, is studying sanitary conditions in and about mines with the intent of pointing out how those conditions that are a menace to the health of the miner may be most efficiently removed or remedied. An out- line of sanitary betterment work at mining villages in the Birming- ham district of Alabama has already been published by the bureau," and in this bulletin are presented suggestions on the planning of mining towns and the construction of miners' houses. The bulletin does not pretend to be a treatise on the so-called "housing problem," and mentions sociologic issues only incidentally. It is assumed that the influence of proper shelter on health is understood and that not a lack of appreciation so much as a lack of knowledge of the best remedies is responsible for many of the undesirable conditions that exist at mining towns. The purpose of this bulletin is to supply facts on the building of well-lighted, well- ventilated, warm, attractive, and economical houses for miners, these houses being assumed to be units of an industrial village or town the building and management of which are under the control of a corporation, so that special conditions hold which do not apply to houses built and owned by individual miners. From this it is not to be inferred that the company-controlled town is the best system or the only one in vogue. The discussion of this side of the subject in all its phases is too involved to be included in this paper. One element in favor of the company-controlled town is its possible immediate responsiveness. Hence this assumption. Also the assumption is made that a-new isolated town is being built, and hence the selection of the site, the arrangement of the streets, and the situation of the houses are discussed before the house itself is treated, for one of the most important factors in obtaining an economical sanitary house is a well-selected town site. Many of the suggestions, however, may be applied in improving conditions in existing towns, in building new houses in old towns, or in repairing old houses. Emphasis must be laid on the fact that as a rule a mining village has a shorter life than a manufacturing town. Economy is emphasized frequently because the discussion is predi- cated upon the assumption that the miner himself is to pay for all that he gets. House rent will doubtless be expected to bring in a reasonable return on all money invested in streets, sidewalks, water supply, sewer system, and houses; in other words, the town is to be run on a business and not on a paternal or charitable basis. "Fair and reasonable" precludes, of course, the idea of excessive returns. Some companies do not consider it good policy to realize as high a rate of interest as an independent realty company would be war- ranted in realizing. Under some circumstances part of the town improvements might be charged as "expense of the industry," that is, to the consumer. The isolation of a mining town introduces a unique responsibility. As the miners are practically obliged to rent the company houses, the officials of the company ought to scrutinize all expenditures in- volved so that house rent may be reduced to a minimum. In a way the town builders are placed in the position of trustees. They deter- mine, within certain limits, what proportion of a man's wages shall be spent on house rent. This consideration should restrain fanciful and unnecessarily expensive building; the other extreme should like- wise be avoided. True economy should be distinguished from cheap- ness. Ugly, insanitary, uncomfortable shacks should not be built even if, because of their cheapness, there is a demand for them from tenants. The obligation of the industry to society as a whole as well us to the tenant ought to forbid this. A cheerful, strong, healthy, virile race will not rise out of the filth and squalor of cheap hovels. An insanitary environment often does its damage slowly and silently; vitiated air does not, like mine gas, announce its deadly work by an explosion. As Talbot⚫ says: Health depends in part on freedom from infection. The probability of obtain- ing that freedom will be greatly increased by maintaining the body at a high state of vigor, or "vitality," as it is popularly called. This implies the promo- tion of all agencies which have to do with the physical well-being as well as with the control of sources of infection. Many men realize that in building houses for their workmen they are invested with a peculiar responsibility that must be wielded wisely, and in large developments they call into consultation the land- scape architect, the sanitary engineer, and the building architect, as well as the mining engineer.

Jan 1, 1914

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners' training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry (Morbidity and Mortality Week Report, 2001; NIOSH, 2002). Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year (NIOSH, 1999). Mine safety and health professionals have long recognized training as a critical element of an effective safety and health program. Federal regulations (30 CFR, Parts 46 and 48) require mine operators to provide initial safety and health training to all new miners, as well as a minimum of 8 hours of refresher training each year. The time and money being spent to train U.S. miners is substantial, and so there is a strong and steady demand for new and better mine training materials and methods. A growing concern among mine safety professionals regards the training of new workers. A major change in the mining workforce is anticipated within the next decade. In major segments of mining, especially coal, relatively few workers have been hired since the 1970's. Thus, as an entire cohort of miners in the current workforce nears retirement, the replacement of these employees will require an influx of new workers. New miners may be young people who lack the ability to recognize and respond to mining hazards in an appropriate manner. They may also have had different educational experiences than their older counterparts. Many safety professionals believe that these two cohorts require different approaches to training. The papers in this report should help prepare mine trainers for the changes about to occur in the workforce and acquaint them with strategies they can use to enhance the effectiveness of their training. The first three papers present basic principles for teaching adults. The five remaining papers are intended to illustrate how these principles can be applied to the development and imple¬mentation of effective training for miners. Below is an overview of these papers. 1. Kowalski and Vaught review the process and principles of adult learning. The learning model they present includes a discussion of goals, content, delivery, assessment, and remediation. Adults are viewed as active learners, experienced-based, expert in their own right in specific areas, independent, real-life centered, task-centered, problem-centered, solution-driven, skill-seeking, self-directing, and internally and externally motivated. Basic aspects of curriculum development are briefly reviewed. For further information about adult learning, see Camm and Cullen's paper. 2. Mallett and Reinke's first paper discusses issues related to training new miners who have recently or will soon be entering the mining workforce. These new generations of miners have different learning style preferences and training needs than Baby Boomers and other older miners. Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these young new workers. This paper provides information that will help mine trainers communicate across the generation gap. 3. Mallett and Reinke's second paper provide an overview of training evaluation. Trainers and decision-makers are given a framework for planning and assessing training evaluation strategies. The authors present Kirkpatrick's (2001) model of evaluation categories and discuss how to start an evaluation plan and various ways to collect data. They do not provide detailed instruction in evaluation methodologies, but give trainers a review of the things they need to consider when developing an evaluation plan. A good evaluation plan can inform revisions to a training course, assess trainee learning, and/or answer managers' questions about program effectiveness. 4. Brnich, Derick, Mallett, and Vaught discuss a technique for incorporating worker participation into fire prevention and safe equipment operation training. This technique involves development of short (5 to 7 minutes) videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner's workplace. An example of one of these training modules is presented, along with the results of an evaluation performed on its effectiveness at improving miners' understanding of what types of information they should be sure to communicate during a mine emergency. 5. Wiehagen, Conrad, Friend, and Rethi discuss on-the-job training (OJT) as a method for teaching miners safety and production skills. Much of the training is done by experienced workers. This paper describes how small investments can help improve the effectiveness of on-the-job training. Effective on-the-job training involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. This paper addresses organizational considerations supporting structured on-the-job

Jan 1, 2002

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

By R. V. Higgins

"INTRODUCTION When nations throughout the world are pitted against each other in a war in which petroleum plays a major role, scientist and engineers of the petroleum industry must give serious thought to ways and means for recover¬ing greater percentages of oil from natural reservoirs than in the past. Petroleum and its products are vital to highly mechanized modern warfare, and the victorious nations will be those whose armies, navies, and air forces are supplied with adequate fuel oil, gasoline, and lubricants until the war is won.Efficient recovery of oil from underground reservoirs depends on many interrelated techniques; evaluation of the producing performance of wells upon the basis of their productivity indexes is one such tool. Oil wells usually yield oil at a maximum rate when first ""brought in"". The rate of production begins to decline soon after the first oil is delivered to the tanks, and although part of the decline usually can be attributed to natural reduction of reservoir pressure as oil and as are withdrawn from the reservoir, a larger proportion frequently is caused by greater saturation of water and as in the producing formation about wells and clogging of the pores of the sands by silt, organic salt, and insoluble hydrocarbons. If the maximum quantity of oil is to be recovered from reservoir sands and rocks by wells, it is then imperative that the ability of wells to produce oil be watched closely and all adverse influences that affect the case with which oil can flow to wells be corrected if possible."

Sep 1, 1942

By H. B. Hill

The Salt Flat field, formerly called the Joe Bruner field, is located northeast of the town of Luling in Caldwell County, Tex. This field, which is a fault structure, approximately parallels and is about 5 miles east of the Old Luling field. The proved area is approximately 1,280 acres, on which 332 producing wells (September, 1930) have been drilled. The majority of the wells are producing from the Edwards limestone at an average total depth of 2,700 feet. A few wells are producing from the Austin chalk or from other formations above the Edwards limestone. The Wilcox formation is exposed, and the fault trace in places is scarcely evident. The strike of the structure is approximately N. 20 to 45° The displacement of the fault is probably 200 to 500 feet. The discovery well was completed in the Austin chalk by the Lutex Oil Co. during April, 1928. In October, 1926, the Sun Oil Co. completed the discovery well in the Edwards pay. This well was an important discovery, as it indicated the potential oil possibilities of the Edwards limestone in echelon fault structures. The discovery led to the development of the third fault field in the Edwards limestone and opened up a large area for future prospecting.

Jan 1, 1931

By Shail J. Butani

In 1986, the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 yr; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. coal mining workforce from March through September 1986. A companion report, Information Circular (IC) 9193, "Characterization of the 1935 Metal and Nonmetal Mining Workforce:' provides similar information for the U.S metal and nonmetal mining industry.

Jan 1, 1988

By Joan Weinberg

Real output expanded at a 3.0% rate worldwide in 1987, a slightly lower pace than the 3.2% rate in 1986. The decline was accounted for largely by slower growth in the U.S.S.R. and the East European countries, as well as in the developing countries (table 1). According to the International Monetary Fund, output of industrial countries output grew 3.1% and rose most strongly in Japan, the United Kingdom, and Canada (table 2). U.S. economic growth remained at 2.9%, the same as in 1986. Consumer and government spending declined in industrial countries, while gross fixed investment: rent increased. This increase in fixed investment expenditures could be attributed partly to lagged results of some 1986 developments: the fall in oil prices, declining interest rates, and exchange rate changes. The U.S. budget deficit, as well as the large external deficits and surpluses among major industrial countries, hindered further growth .2 A report from the Organization for Economic Cooperation and Development (OECD) indicates that the impact of the October stock market crash was short-lived because it hit economies that were growing strongly, anyway.3 The growth of output in the developing countries slowed in 1987; however, output declined in the fuel-exporting developing countries. These countries have been adversely affected by weakness in oil prices and the depreciation of the U.S. dollar. The weighted average of inflation rates in industrial countries--as measured by the [ ] GNP deflator, was 2.9% in 1987, down from 3.4% in 1986. Prices rose 3.0% in the United States, up from 2.6% the previous year. Inflation for 1988 is expected to remain slightly higher in the United States than in Japan and the Federal Republic of Germany because of recent exchange rates changes and the elimination of slack productive capacity and labor in the U.S. economy. Prices in developing countries as a whole rose more than 10 percentage points in 1987. Higher import prices, caused by

Jan 1, 1988

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By Richard F. Hewlett

Computing average grade and tonnage either for an entire ore deposit or for individual blocks of ore is a continuing problem in mining. As part of a research program, investigating application of statistical techniques to mine sampling, Bureau of Mines engineers at the Denver Mining Research Center have made extensive use of an electronic digital computer for developing mine sampling theory, simulation of ore deposits, and analysis of mine sample and assay data. This report is one of a series describing use of the digital computer for rapid solution of computing problems in the mining industry.3 4 Development of a computer program to compute ore reserves by the commonly used triangular method was necessary so that results could be made available for analysis within hours.

Jan 1, 1963

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Joel N. Van Sant

The rapidly expanding economy of the West, with its growth of heavy industry, and increased steel production, is primarily responsible for the refractory clay industry's concern over the adequacy of the clay supply in States of the Great Plains and Rocky Mountains. Hence, the investigation by the Federal Bureau of Mines of the occurrence and use of refractory clays in North Dakota, South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona has been encouraged by the major consumers and producers of this commodity. The Wyoming investigation is a part of the national program devised to close gaps in the domestic supply of specific types of clays to determine their characteristics and properties and to provide information that will assist the refractory-clay industry. Forty-two locations of clay-bearing rock in 17 areas in Wyoming were examined (fig. 1). Location 3 was not examined during this survey. Its description was taken from an earlier report. Locations 20, 21, and 22 were previously reported but were, also, examined by the Bureau. No samples were collected from these locations because field examination indicated that the shales were not refractory grade. The Hulett, Aladdin, and Newcastle areas are discussed in the section on the Black Hills district; the other 14 areas are described separately.

Jan 1, 1961

By Allen L. Frank

The uranium mine environment is characterized by airborne radon-222 and its daughter products to which miners are exposed through breathing and by gamma and X rays from the uranium-235 and uranium 238 chains to which the miners are exposed externally. The nature of the radon-daughter concentrations and the methods used to define and measure the exposures are explained through an extensive review of the literature. An improved passive track-etch dosimeter for personal use is proposed which has a measurement range of about 30-400 WLH with a 95% confidence interval to ~25% for individual detector measurements in relatively stable mine air. Some measurements of these dosimeters adapted to environmental use are also presented. A program of development for enhancement of dosimeter sensitivity and greater accuracy of measurement is outlined. Extensive gamma-ray survey measurements were made in two Colorado and three New Mexico mines. Follow-up personal miner dosimetry with LiF TLDs was done at the mine with the highest exposure rates, The average miner exposure rate measured was 4.27 mR per day, or 9.3 of the maximum permissible level averaged over 13 weeks. Comparisons are made with previous mine surveys and their value in estimating miner exposure is discussed. Some depth-dose measurements made using Lucite as the absorber are evaluated.

Jan 1, 1978

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By James N. Bayne

An examination and analysis of Landsat digital data in the monitoring of surface mines in selected counties of South Carolina.

Jan 1, 1979

7133. Clewell, D. H. The Gravimeter. Prec. and Trans. Texas Acad. Science 1941, Austin, Tex., vol. 25, 1942, pp. 86-88. Static gravimeters, unastatized and. astatized, are considered to be the most practical for oil exploration. One gravimeter is described using a beam whose moment about a pivotal axis is elastically balanced. Magnetic or electric fields are deemed unsatisfactory for balancing gravitational force because they cannot easily be kept constant. The gravimeter described is capable of detecting a change in altitude of 3 inches and a change in latitude of about 150 feet. V. S.

Jan 1, 1944

By Paul M. Tyler, R. M. Santmyers

Platinum and its allied metals osmium, iridium, rhodium , palladium, and ruthenium are the most costly of the better-known metals and combine properties that make them unique among the elements . For a number of isolated uses substitutes have been found which are cheaper and quite as satisfactory ; but none will replace platinum in many of its varied uses , and there is a large and growing demand for purposes for which no economical substitutes are known . As this paper is being written the supply of platinum tends further to increase as a result of the exploitation of newly developed resources and the expansion of production from older sources . In obedience to economic law prices have declined steadily . Buyers , always reluctant to commit themselves on a falling market , have maintained a waiting attitude , and consumption trends are not clearly indicated . Should platinum again approach the price of gold , the natural tendency would be to use more of the metal . In recent years , however , the industrial and scientific uses of platinum have become subordinate to its consumption in jewelry . In matters of personal adornment the popular whim and not practical utility is the dominant factor in demand , and it does not follow that lowered prices will stimulate demand . The substitution of white gold and certain plated goods for platinum may be checked by cheaper platinum , but a fickle public that turned from gold to platinum when platinum became the more costly metal can not with certainty be expected to buy more platinum jewelry because more of the metal than formerly may now be had for the same price . The dearth of platinum during and for some years after the World War had a profound effect upon prices , and this in turn wrought important changes in the field of consumption . When prices advanced the chemical industry, formerly the leading consumer of platinum, was forced to economize in its consumption of the metal and to substitute other metals whenever it could . Somewhat similar conditions resulted in the electrical industry and in the use of platinum in dentistry . Some of these former outlets are permanently closed , and others may be reopened now that platinum prices have receded to pre-war levels , but despite the general expansion of industrial and scientific activity since 1913 the demand for platinum outside the jewelry trade has suffered a net decline . Since the metallurgy of platinum is relatively simple the reason for its high price is its relative scarcity in the earth's crust . An interesting speculation set forth by certain geologists attributes the extraordinarily high density of the interior of the earth in part to the presence of iron alloyed with substantial amounts of platinum and other related metals . In support of this hypothesis it may be said that platinum is often found in meteorites , and known deposits in the earth's crust are all of deep - seated origin . However , even if there were a high concentration of platinum in the interior of the earth it would be next to impossible at the present state of our knowledge to make it available , and the world would continue to depend for its supply on deposits found within minable depths below the surface . For many years before 1914 the world obtained its supply of platinum metals primarily from Russia , which before the war produced as much as 300,000 troy ounces in a year , or approximately 95 per cent of the world output . Despite fluctuations due to internal political disturbances Colombia managed to account for 3 to 4 per cent , leaving the rest of the world to furnish the remaining 1 to 2 per cent .

Feb 1, 1931

By Paul M. Tyler

According to Lindgren , the economic importance of pegmatites stems from the fact that they represent the principal natural storehouse of two classes of mineral products : (1 ) common minerals in exceptional size and purity and ( 2 ) several of the rarest minerals , which are not commercially available from other types of deposits . Most pegmatites can be described simply as coarse- to very coarsegrained granites . Pegmatite includes coarse -textured igneous rocks of any composition , such as syenitic , alkali syenitic , dioritic , or gabbroitic ; but basic pegmatites are far less common than those that are associated with acid rocks and correspond approximately to the mineral composition of ordinary granite . Moreover , only a very few basic pegmatites can be considered as economic sources of useful minerals . Whereas , in ordinary granitic rocks the individual minerals usually measure 1/8 to 1/4 inch across , in pegmatites they are characteristically over 1 inch and often more than 12 inches in diameter . Although some of the constituents of the pegmatite may be only a fraction of an inch in length , single crystals more than 10 feet long are by no means unusual , and some crystals are enormous . A whole quarry was operated in the Urals within a single crystal of feldspar . Huge quartz crystals are quite common although usually imperfect . Muscovite plates 10 feet in diameter have been mined in India , and the Purdy mica mine in Canada contained a mica crystal measuring 6.5 by 9.5 feet and weighing nearly 7 tons , which supplied more than $20,000 worth of trimmed mica sheet . A loglike crystal of spodumene in the Etta mine in the Black Hills of South Dakota was 42 feet long . Giant crystals of beryl weighing several tons apiece have been mined from several properties . Because so many rare minerals are found in substantial concentration only in pegmatites , it is a common fallacy to suppose that pegmatites are always enriched in rare elements . Traces of most of these elements , of course , are found in almost all igneous rocks , and they reappear in the sediments derived from igneous rocks . It does not follow , however , that all or even most pegmatites contain higher percentages of rare elements than other granitic rocks . Geological evidence points to the probability that notable concentrations of rarer minerals or elements in pegmatites are more or less fortuituous , such additions often being ascribed to events subsequent to the original emplacement of the main body of the pegmatite . Most pegmatites consist principally of potash , feldspar , and quartz . Even mica , although commonly present , is not an essential constituent . Probably

Feb 1, 1950