Search Documents

By M. C. McCall

When electric current of any appreciable magnitude flows from a power line into the earth, a change sometimes takes place in the conditions of resistivity immediately surrounding the electrode or medium of contact. If the conducting medium is composed of moist earth or clay the effect is to increase rapidly the resistance. If the conducting medium is coal or a coal bed, the effect is one of slowly decreasing resistance as the coal is carbonized, If, however, the flow of current is not enough to carbonize the coal, it will dry slowly, with a resultant increase in resistance. Measuring ground resistance, or impedance, with conventional commercial ground testers does not always indicate the current that will flow in the earth circuit from a direct-current or an alternating-current power circuit. The exact reason for this has not been determined however, it is thought to be due to the comparatively minute currents used for such testing. A typical ground, tester used by the authors for this work indicated a maximum current of 25 milli-amperes. The frequency of this testing current also has an effect on the readings in all probability. While the possibilities of the effects of varying frequencies has by no means been fully explored in this investigation, there are very definite indications that the impedance of a circuit through a section of earth will vary in some inverse relationship to the frequency of the applied voltages. This is evident at ordinary power-line frequencies ns well as at higher frequencies up to 200 kilocycles, which was the highest frequency available for tests in this investigation. This report is written in the hope that it will stimulate further investigation of the possibilities suggested for communication and the development of safety devices for increased electrical safety in coal mining.

Jan 1, 1952

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By G. S. Scott

The Bureau of Mines is engaged in research to assess the hazards associated with the handling, storage, and use of combustible gases, vapors, and. liquids encountered in mines and in industry. As a part of this general pro-gram, numerous limits of flammability and ignition temperatures are being investigated for a wide variety of combustible materials, and methods are being developed to minimize the explosion hazards of these combustibles. The Bureau receives numerous requests for information on the explosion hazards of specified combustible mixtures under various conditions of use. This information circular has been prepared to assist those who may have similar requests. Destined primarily for the layman with a limited technical knowledge of the subject, it considers rather briefly the numerous factors that enter into the general problem of gaseous explosions and their prevention.

Jan 1, 1951

By Phillip N. Yasnowsky

This Bureau of Mines report examines the percentage depletion allowance rate structure in relation to several criteria that are indicative of U.S. mineral import dependence. These criteria are the minerals considered as strategic and critical for stockpiling purposes, the ratio of reserves to forecast cumulative demand (1976-2000) for selected minerals, and the U.S. net import reliance as a percentage of apparent consumption (1978), also for selected minerals in general, it was Found that there does exist a direct, although not perfect, relationship between the percentage depletion allowance rates and the degree of import dependence as indicated by these three criteria. The higher percentage rates tend to he associated with those minerals for which the United States is, or will likely he, heavily dependent on foreign sources. In addition, a basic discussion of the mineral depletion allowance is provided, including numerical examples illustrating the computation of the allowance under several assumptions. Also, the percentage depletion allowance rates for individual minerals are tabulated.

Jan 1, 1980

By James W. Ballard, H. H. Schrenk

"The X-ray method of quantitative determination is advantageous because it permits determination of compounds rather -than ions or elements; for example, the direct determination of quartz in silicates,4/,5/,6/ The method also takes into account the finest particles of a sample, which may be lost in wet chemical methods because of solubility or in petrographic methods because of limitation of the microscope. The sample is usually reduced to a powder and is easily prepared,7/ only a few milligrams of material being necessary. The sample and its chemical composition are not destroyed and may be used for further analysis by X-ray diffraction or by other methods.This paper presents in detail some of the more essential problems that arise in the application of X-ray diffraction to quantitative chemical analysis, Photometric measurements are discussed in connection with line intensities and the choice of X-ray film. The internal standard method, successfully used in spectrographic analysis, is applied.Copper K-alpha X-rays from a demountable research-type X-ray tube were used with a camera of 20 centimeters radius with a cast-lead-slit collimating system. A combination of a tilted wedge and a lead-slit collimating system permitted irradiation of a large amount of sample with X-rays. This tended to minimize errors due to possible inhonogeneity of the sample, to decrease the time of exposure, and to keep the lines on the X-ray film to a minimum width. There was sufficient dispersion of the lines for satisfactory analysis of most samples. Power was furnished the tube by a. source of constant high potential consisting of a synchronous motor generator furnishing 500-cycle power to a 100-kv. transformer, rectifying valves, and a condenser filter circuit. The X-ray tube was operated as a gas-type tube at 35 kv, and 20 ma,, the exposure times varying from 1 to 2 hours. The constant output of X-rays from the tube, indicated bar an exposure meter built for the purpose, was satisfactory.The recording microphotometer8/has been described. It was found preferable to a nonrecording instrument for measuring blackening of lines above a background on X-ray films. This background, which usually occurs, is sometimes complicated by numerous peaks from lines of complex diffraction patterns. is microphotometer record of the pattern, therefore, facilitates the location of the background 'and the measurement of the heights of the peaks and thus contributes to the accuracy of a determination."

Jun 1, 1946

By Wing G. Agnew, Paul L. Russell

"INTRODUCTION During the past few years, the development of millisecond-delay electric blasting caps has made possible a more flexible control over timing the firing of individual charges in blasting, The use of these caps has proved especially productive in quarry blasting and in numerous construction operations, but their use in underground mining is developing more slowly, although in some cases, as the solution to a difficult breaking problem, they have been well-received. When used in metal-mine drifts, the general objection is that the broken rock is thrown too far. In nearly all cases, however, use of millisecond-delay caps results in better fragmentation of the rock and a lower powder consumption per ton of rock broken.Prom 1949 to 1952, several series of experiments were conducted at the Mount Weather, Va., Experimental mine in conjunction with driving a 6- by 10-toot ventilation raise. 3/4/ The raise-round experiments in this 238-foot shaft, using millisecond-delay electric blasting caps in various drill-round patterns, are the subject of this report.SUMMARY AND CONCLUSIONSAll rounds discussed in this report were drilled in the hard rock (epidosite and greenstone) of the ventilation raise at Mount Weather Experimental mine (figs. 1 and 2). The drill-round patterns varied from 28- to 32 holes and from a V-cut design to one having no cut boles at all. With the exception of the first two rounds, all blasting was done with millisecond-delay electric blasting caps. In all rounds 60-percent ammonia gelatin dynamite was used and holes were stemmed with two cartridges of sand stemming."

Apr 1, 1953

By P. D. Kovscek

High-pressure streams of water, known as water jets, can be used to improve the cutting efficiency of mechanical bits. During prior testing by the Bureau of Mines, the cutting performance of a longwall shearer, equipped for water-jet-assisted cutting, was evaluated. The performance of the shearer did not improve while using water jet assist because the pressure of the water delivered to the rock surface was inadequate. The study, described in this report, resulted in a determination of the major cause of water pressure loss on the shearer, and an evaluation of the techniques for increasing the water pressure at the rock surface. The results show that the major pressure loss, which occurred between the nozzle and rock surface, is directly affected by the amount of fluid turbulence that develops just upstream from the nozzle. Preventing a sudden change in the direction of the flow channel can increase the stagnation pressure as much as 400 pct. Smoothing the surface of the flow channel in the shearer bit block would increase the stagnation pressure delivered to the rock surface by 35 pet.

Jan 1, 1989

By J. M. Mutmansky, L. Xu

"This paper outlines the results obtained when sampling twenty underground coal mine sections, each in a different mine. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a rather detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons on the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines that contain only diesels used for outby utility haulage. Particulate in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be achieved from the limited data collected in this study, the data indicates that more detaile~ study of particulates in diesel mines is needed so that some idea of the particulate loadings in diesel mines can be achieved."

Jan 1, 1988

By Thomas M. Nasiatka

Tests with a high-pressure water jet were conducted in the steeply pitching Roslyn No. 5 bituminous coalbed in the Roslyn No. 9 mine, Roslyn, Wash., to determine the feasibility of extracting coal from pillars and from a solid coal face in development without drilling and blasting. During pillar mining, using a hand-held monitor, the best results were obtained with a 0.150-inch- diameter nozzle, a water pressure of 3,500 psi, and a flow rate of 38.5 gpm.3 The rate of mining and productivity were 0.74 ton per minute and 16.6 tons per man-shift, respectively. During development mining, using a monitor mounted on a roof jack, the best results were obtained with a 0.148-inch-diameter nozzle, a water pressure of 4,500 psi, and a flow rate of 40.0 gpm. In one section of the mine where the coal was relatively hard, the rate .of mining and productivity were 0.10 ton per minute and 5.7 tons per man-shift, respectively in another section of the mine where the coal was relatively soft, the rate of mining and productivity were 0.51 ton per minute and 8.3 tons per man-shift, respectively. The tests showed that hydraulic mining methods were more productive than conventional mining methods in pillar mining. In development the productivity of hydraulic mining depended primarily upon the coal hardness. Compared with conventional methods, hydraulic mining methods were less productive where the coal was relatively hard and equally as productive where the coal was relatively soft.

Jan 1, 1963

By P. C. Good

Work was done to determine conditions necessary for efficient electrodeposition of aluminum from fused chloride electrolytes. Aluminum was deposited from a molten chloride salt electrolyte over a temperature range of 150° to 750° C. At lower temperatures in a heat-resistant glass cell, aluminum was deposited on stainless steel and on aluminum cathodes. The deposit was recovered in the form of light, feathery dendrites that could not be consolidated. At 750° C, molten aluminum was deposited at cathode current efficiencies as high as 90 to 100 percent on titanium diboride cathodes and in molten aluminum cathodes. Nitride-bonded silicon carbide was the best cell material, although porcelain was also used. The electrolyte consisted of a mixture of sodium and potassium chlorides in 1 to 1 mole ratio, containing aluminum chloride in concentrations ranging from 2 to 30 weight-percent in cells holding up to 1,000 grams of electrolyte. Generally favorable results were attained in studies made at temperatures greater than the melting point of aluminum.

Jan 1, 1966

By Jr. Norman

The Bureau of Mines investigated the thermoelectric properties of yttrium selenides and tellurides from room temperature to 900° C. X-ray crystallographic data were determined for the yttrium-selenium and yttrium-tellurium compounds that were orthorhombic with a cubic substructure. The yttrium selenides and tellurides exhibited semimetallic to insulator conduction properties with figures of merit of 10-9 to 10-4 °C-1. The mono-selenide and monotelluride behavior was partially degenerate; unsatisfied bonds were the source of the large number of charge carriers. The higher stoichiometry selenide compounds were intrinsic semiconductors) but with high electrical resistivities. A critical defect or impurity ionization energy for carrier activation appeared to exist in the majority of telluride compounds. Mobility and energy band determinations are required to interpret completely the observed effects in most of the compounds studied.

Jan 1, 1966

By Stephen P. Holt

In the fall of 1946 and spring of 1947 the Bureau of Mines put down five inclined diamond-drill holes totaling about 3,100 feet of bore to test for the possible eastward extension of the Royal Princess ore deposit in Jo Daviess County, Ill. Attention of the .Bureau was first directed to this property by the Illinois State Geological Survey. The history of production of the Royal. Princess mine and reports as to the size and nature of the deposit were considered justification for investigating the trend of the mineralization. This report describes the work done by the Bureau of Mines and presents the data obtained.

Jan 1, 1948

By Frank C. Andreuzzi

The Division of Environmental Activities, U.S. Bureau of Mines, conducted a solid waste demonstration project on a burning coal refuse bank. The primary objective of this project was to develop and evaluate an efficient method of extinguishing burning coal refuse and moving it. A series of tests were performed using water monitors and related apparatus to quench the burning material and, at the same time, using earth-moving equipment to transport, spread, and compact the extinguished material. The method found to be most effective consisted of water-quenching the surface material to a workable depth, ripping, and removing the quenched material with a bulldozer and tractor-scraper. The total cost was estimated to be $0.44 per cubic yard.

Jan 1, 1970

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By Martin H. Rogoff

The presence of antibiotic materials extractable with polar organic solvents was demonstrated in coals of various ranks. Since these antibiotics occur in low concentrations, 200 pounds of a high-volatile C coal was extracted with acetone at room temperature to obtain sufficient material for detailed study. The biologically active materials in the extract were concentrated by extracting with aqueous sodium hydroxide. The fractions soluble in sodium hydroxide inhibited bacterial cultures when present in concentrations comparable to those at which other antibiotics are active (5 µg/ml). Steam distillation of the extracts did not yield highly active materials, contrary to the finds of other investigators. Mass spectrometry of the extract indicated, mainly, the presence of 6-ring compounds in the region of mass 324 to 392. The predominance of 3-ring aromatic systems found by ultraviolet analysis suggests compounds such as biphenanthryl or similar structures. The activity of the hydroxide- soluble material decreased markedly when the phenolic hydroxyl groups were transformed into trimethylsilyl ethers. Hydrolysis of the ethers yielded a product having the same activity as the original material, which indicates that phenolic compounds are largely responsible for the antibiotic activity observed.

Jan 1, 1963

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

By Robert R. Stein

Occupational noise caused by the rock drills used in mining was investigated by the U.S. Bureau of Mines. Using a large reverberation chamber and an automated drill test fixture (ADTF), the sound power levels of mining drills were measured to determine if there are types of drills that are advantageous from a noise production standpoint. Test results show that while there are not large variations among types of drills, there are still some choices that could produce a positive effect on overall noise exposure. It is also shown that lower noise exposures are possible using larger drills because of higher production rates and better operator positioning.

Jan 1, 2010